Netwerk Case Study - Typepad · 2014-06-11 · Cisco Small Business SG 200-50 ... Remove the static...
Transcript of Netwerk Case Study - Typepad · 2014-06-11 · Cisco Small Business SG 200-50 ... Remove the static...
Abdellah El Ghrich Yassine Benayyoub
Netwerk Case Study
1
Inhoudstafel
Inleiding ................................................................................................................................................... 3
Probleemstelling ...................................................................................................................................... 4
Doelstelling .............................................................................................................................................. 4
Netwerk installatie .................................................................................................................................. 5
Plan ........................................................................................................................................................ 13
Kosten .................................................................................................................................................... 14
Cisco Small Business SG 200-50 .................................................................................................... 14
ISP .......................................................................................................................................................... 15
Literatuurlijst ......................................................................................................................................... 16
Bijlage .................................................................................................................................................... 16
Configure the hostname of the switch as Switch1. ............................................................................... 17
Set the privileged EXEC mode password to cisco .................................................................................. 17
Set the privileged EXEC mode secret password to class ....................................................................... 17
Configure the console and virtual terminal lines to use a password and require it at login. ............... 17
Enter the interface configuration mode for VLAN 1. ............................................................................ 17
Configure the FastEthernet 0/0 interface with the IP address 192.168.1.1/24. ................................... 17
Configure the Serial 0/0/0 interface with the IP address 192.168.2.1/24. Set the clock rate to 64000.
............................................................................................................................................................... 17
Perform basic configuration of router R2 ............................................................................................. 18
Configure the FastEthernet 0/0 interface with the IP address 192.168.3.1/24. ................................... 18
Remove the static route to 192.168.3.0. .............................................................................................. 18
Enable RIP v2 routing and advertise the participating networks. ......................................................... 18
Remove the static route to 192.168.1.0 ............................................................................................... 18
Enable RIP v2 routing and advertise the participating networks. ......................................................... 18
To allow the switch port FastEthernet 0/1 to accept only one device, configure port security as
follows: .................................................................................................................................................. 18
View the show mac-address-table options ......................................................................................... 18
Disable unused ports ............................................................................................................................. 19
Examine the spanning-tree tables on each switch ................................................................................ 19
Determine the options that can be configured for the Spanning Tree Protocol by issuing this
command: .............................................................................................................................................. 19
By default, the port priority of an interface is 128. Lowering this value will ensure a specific interface
becomes the Root Port:......................................................................................................................... 20
Configuring, Verifying, and Troubleshooting VLANs ............................................................................. 20
Creating VLANs and Assigning Ports...................................................................................................... 22
2
Configuring a Trunk Port to Connect Switches...................................................................................... 23
To allow connectivity within multiple VLANs across multiple switches, trunking can be configured.
Without trunking, each VLAN requires a separate physical connection between switches ............ 24
Implementing EIGRP .............................................................................................................................. 25
Configuring and Verifying Single Area OSPF .......................................................................................... 26
3
Inleiding
Wij hebben de opdracht gekregen om een nieuwe netwerk te maken voor het school. Wij
mogen zelf kiezen voor wie we veranderingen maken. De bedoeling daarvan is dat we een
goed gestructureerde plan maken om er voor te zorgen dat wanneer andere technicus komen
dat ze dit natuurlijk zonder problemen kunnen alles terug vinden.
Onze klant is Sean up een jonge onderneming van ongeveer 300 mensen. Zij hebben het
gebouw gekocht voor een totaal van 1,5 miljoen euro. Zij hebben ons gecontacteerd om de
netwerk plan te tekenen en alle materiaal daarvoor te zoeken.
Zij willen dat alle computers met elkaar kunnen communiceren omdat in dit bedrijf is iedere
afdeling verbonden aan elkaar. Dus onze taak is om de beste plan te tekenen en ervoor zorgen
dat iedereen met elkaar kan communiceren.
Het gebouw heeft 8 verdieping en per verdieping werken er ongeveer 40 personen. Het hangt
af van de afdeling zelf. Er werd aan ons gezegd dat we zelf mogen kiezen over hoe we te werk
gaan. Wat het bedrijf wilt is het eindresultaat en met de juiste prijs op het markt.
Ze zijn dus naar het juiste plaats gekomen.
4
Probleemstelling
Sean up heeft een nieuwe gebouw gekocht en heeft geen idee op welke manier hun netwerk
zal werken. Daarom hebben ze ons gecontacteerd om dit probleem op te lossen. Wij hebben
la carte blanche met andere woorden wij zijn vrij om zelf te kiezen wat er gaat gebeuren. Zij
hebben per verdiep 40 pc die elke dag gebruikt moeten worden behalve de weekend. Die
computers moeten met elkaar kunnen communiceren. Want het bedrijf werkt op vele projecten
tegelijkertijd en hebben alle afdeling iets te maken met de andere.
Dit wil zeggen dat er ongeveer 300 computers elke dag zullen gebruikt worden. En dat de
netwerk bandbreedte vol zal zijn. Die computer moeten ook op internet kunnen geraken.
Mensen van de administratieve afdeling moeten ook op alle verdieping kunnen printen. Want
die hebben geen vaste plaatsen en staan af en toe in verschillende verdieping per dag.
Doelstelling
Onze doel is er voor zorgen dat alle computers op het internet kunnen en dat ze allemaal
tegelijkertijd documenten kunnen delen. Wij moeten ervoor zorgen dat onze plan perfect wordt
getekend om geen stoornissen te hebben. Wij zullen voor een ISP zoeken die de beste prijs
in de markt heeft. En die ook natuurlijk 24/24 beschikbaar is als er een probleem zou ontstaan.
Natuurlijk dit zou niet kunnen gebeuren dankzij ons goede werk.
5
Netwerk installatie
Onze netwerk hebben wij in 9 verschillende VLAN’s gedeeld waarbij elke VLAN’s met de
verdiepingen van het gebouw corresponderen. Wij zijn op een gelijkaardige manier als de
“bottom-up” design tewerk gegaan voor het maken van onze netwerk.
Eerst hebben wij de IP-adressen en de subnetmasks aan de host’s toegegeven door erop te
dubbelklikken en vervolgens door op de Desktop tab te klikken.
Nu kunnen wij hierin specifiek de Ip-address van onze host en subnetmask ingeven.
6
Verdieping Network SubnetMask
8 192.168.8.0 /24 7 192.168.7.0 /24 6 192.168.6.0 /24 5 192.168.5.0 /24 4 192.168.4.0 /24 3 192.168.3.0 /24 2 192.168.2.0 /24
Nu wij klaar zijn met ingeven van onze ip-addressen en subnetmasken gaan wij de switchen
instellen. Elke switch correspondeert met een verdieping zodanig dat latere
netwerkbeheerders gemakelijk hun weg kunnen vinden als zij het structuur van de netwerk
willen veranderen.
Eerst en vooral moeten wij een straight through kabel tussen onze host en switch aansluiten.
Nu dit gedaan is kunnen wij beginnen met het configureren van onze switch, dit doen wij
dankzij de command line.
7
Wat moeten wij nu precies configureren op onze switch ?
VLAN’s aanmaken
VLAN’s aan poorten ingeven
Trunk
VLAN’s aanmaken:
Switch(config)#vlan 7
Switch(config-vlan)#name Verdieping7
Switch(config-vlan)#exit
Switch(config)#interface vlan 7
%LINK-5-CHANGED: Interface Vlan7, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan7, changed state
to up
VLAN’s aan poorten aansluiten:
Switch(config)# interface fastethernet 0/17
Switch(config-if)#switchport access vlan 7
Switch(config-if)#switchport mode access
Switch(config-if)#end
Nu wij de VLAN’s hebben aangemaakt en die aan de poorten hebben ingegeven gaan wij nu ervoor
zorgen om de Cross-over kabel tussen de switch en de Multilayer Switch te trunken.
TRUNK:
S1(config)#interface fa0/1
S1(config-if)#switchport mode access
S1(config-if)#switchport mode trunk
S1(config-if)#end
We zijn klaar met het configureren van de switchen, we kunnen eindelijk met de Multilayer Switch aan
de slag gaan.
(Niet vergeten om de command “ip-routing” op uw multilayer switch te doen)
TRUNK
8
Wat moeten wij erop Configureren?
VLAN’s ip-addressen ingeven
Trunking kabels
Default-gateway van de hosten instellen
VLANS’s ip-addressen ingeven:
Switch(config)#interface vlan8
Switch(config-if)#ip address 192.168.8.1 255.255.255.0
Switch(config-if)#no shutdown
Switch(config-if)#exit
Switch(config)#interface vlan7
Switch(config-if)#ip address 192.168.7.1 255.255.255.0
Switch(config-if)#no shutdown
Switch(config-if)#exit
Trunking kabels:
Default Gateway van de hosten instellen:
Nu wij klaar zijn met het ingeven van ip-addressen aan de multilayerswitch kunnen wij nu de
defaultgateway naar de multilayerswitch sturen. Dit is veel beter dan alles naar de router sturen omdat
het effeciënter en beter is voor de router.
TRUNK
Stemt overeen met de ip-addres die
wij aan vlan 8 hebben ingegeven.
9
We kunnen perfect nu tussen de verdiepingen pingen:
Wat moeten wij nu instellen om de verdiepingen van 4 tot en met 1 te pingen?
Om de verdiepingen te kunnen pingen zullen wij routers moeten instellen tussen onze twee multilayers
switchen. Zij zullen ervoor zorgen dat de hosten die op verdiepingen 8 -> 5, de hosten op de
verdiepingen 4 -> 1 zullen pingen.
Vooraleer wij de serial kabels tussen de routers kunnen aansluiten moeten wij ze eerst in de router
zelf insteken.
Kies voor WIC-1T (dit zijn de seriele
connecties)
(Vergeet niet uw router eerst te uitschakelen)
10
Nu de routers geconfigureerd zijn met de nodige hardware gaan we nu de seriale verbindgen tussen
hun aansluiten. We zullen een serial DTE kabel gebruiken zodanig dat wij de clock rate van de routers
kunnen configureren.
Met één ip-address hebben wij genoeg om de 3 routers aan te sluiten:
Subnetting
We gaan de ip-address 192.168.20.xx gebruiken voor de routers met een subnetmask van
255.255.255.252 (/30)
We hebben nu alles om onze router perfect te kunnen configureren.
Verbindingen
192.168.20.1/30 192.168.20.2/30 192.168.20.5/30 192.168.20.6/30 192.168.20.9/30 192.168.20.10/30
Router0(config-if)#interface serial 0/0/0
Router0(config-if)#ip address 192.168.20.1 255.255.255.252
Router0(config-if)#clock rate 64000
Router0(config-if)#no shutdown
Router1(config-if)#interface serial 0/0/0
Router1(config-if)#ip address 192.168.20.2 255.255.255.252
Router1(config-if)#no shutdown
Alles is nu klaar maar waarom kunnen wij niet pingen ?
We moeten een routing-protocol kiezen (in ons geval OSPF) om de netwerken te verbinden.
Routers communiceren door middel van protocollen, zoals het Internet Protocol. Daarnaast
worden er protocollen gebruikt voor het routeren van pakketten door het netwerk.
11
Implementatie van OSPF op de routers:
We zullen op elke router en Multilayer Switch hun OSPF routing proces moeten instellen.
Vergeet niet dat elke netwerk in de area 0 moet zijn.
Router0(config)#router ospf 1
Router0(config-router)#network 192.168.20.0 0.0.0.3 area 0
Router0(config-router)#network 192.168.20.4 0.0.0.3 area 0
Router0(config-router)#network 192.168.30.0 0.0.0.255 area 0
Router0(config-router)#end
Router0(config)#router ospf
Router0(config-router)#log-adjacency-changes
Router0(config-router)#default-information originate
Router0(config-router)#end
Router2(config)#router ospf 1
Router2(config-router)#network 192.168.20.0 0.0.0.3 area 0
Router2(config-router)#network 192.168.20.8 0.0.0.3 area 0
Router2(config-router)#end
Router2(config)#router ospf
Router2(config-router)#log-adjacency-changes
Router2(config-router)#default-information originate
Router2(config-router)#end
Router0(config)#router ospf 1
Router2(config-router)#network 192.168.31.0 0.0.0.255 area 0
Router2(config-router)#network 192.168.20.8 0.0.0.3 area 0
Router2(config-router)#network 192.168.20.4 0.0.0.3 area 0
Router0(config-router)#end
Router0(config)#router ospf
Router0(config-router)#log-adjacency-changes
Router0(config-router)#default-information originate
Router0(config-router)#end
Implementatie van OSPF op de Multilayer Switch:
Switch#(config)#router ospf 1
Switch#(config-router)#network 192.168.30.0 0.0.0.255 area 0
Switch#(config-router)#network 192.168.5.0 0.0.0.255 area 0
Switch#(config-router)#network 192.168.6.0 0.0.0.255 area 0
Switch#(config-router)#network 192.168.7.0 0.0.0.255 area 0
Switch#(config-router)#network 192.168.8.0 0.0.0.255 area 0
Switch#(config-router)#end
Switch#(config)#router ospf
Switch#(config-router)#log-adjacency-changes
Switch#(config-router)#default-information originate
Switch#(config-router)#end
12
We komen aan het einde van onze technische gedeelte, alles werd perfect ingesteld en gaan
nu zien of wij tussen de hosten van verschillende verdiepingen kunnen pingen.
13
Plan
1ste en 2de verdiep 3de verdiep 4de en 5de verdiep
6de verdiep 7de verdiep 8ste verdiep
14
Kosten
Material Hoeveelheid Prijs Cisco Small Business SG 200-50 48 poort
8
€ 483.95
Cisco WS-C3750G-24TS-E1U Catalyst 24 Port PoE 4 SFP Enh Multilayer 1RU Ethernet Switch 24 Poort
2
€ 502.20
Cisco router: 2911 Integrated Service Router
3
€ 1071.00
TOTAAL:
€ 8089
Dit is het totale van de materiaal die er moet betaald worden. Dit zijn niet de totale kosten want er
moet nog de kosten van de ISP bij komen en de kosten van de dienst die wij geleverd hebben.
Aantaal werknemers Uurloon Aantal uren
1 € 50/uur 240
1 € 50/uur 240
TOTAAL: € 24000
15
ISP
Belgacom Pro
Fibernet XL
Internet 100 Méga
België Gratis België Gratis België Gratis Hulpdienst Binnen 5 uur Binnen 1 dag Binnen 2 dagen
Download: 30 Mbps
120 Mbps
200 Mbps
3G internet: 2GB
Geen
Geen
62 , 75 /maand
64.95/maand
39,90€/maand
Wij komen nu aan onze totaal kostprijs van dit project. Het heeft voor de onderneming € 32089
gekost om alles te kunnen installeren en doen werken. Natuurlijk komt er nog een extra kost
“ISP” zij moeten € 63 per maand betalen. Natuurlijk dit is de kost voor het eerste jaar. Na het
tweede jaar kunnen ze voor € 5000 per jaar onze diensten gebruiken. Als er een probleem zou
ontstaan dan zijn wij binnen de uur beschikbaar om de problemen op telossen.
16
Literatuurlijst
Cisco router
http://www.centralpoint.be/fr/routeurs/cisco/2911-integrated-service-router-art-cisco2911-k9-
num-
315432/?utm_source=google&utm_medium=cpc&utm_campaign=productlistingads&gclid=CjgKEAjw
2dqcBRC2q-LXjpfxjnQSJAAeYF5L70p1Xmg-jpnzRrVhX0FpRcBHDShIoZfHj5imB5CEOvD_BwE
ISP vergelijking
http://www.astel.be/operateurs/Belgacom/Pack-Comfort-Telephone-HappyTime-XL-International-
Internet-Partout-TV
Multylayer switch
http://www.alibaba.com/product-detail/Cisco-WS-C3750G-24TS-E1U-Catalyst_1126082079.html
Switch 48 ports
http://www.ldlc.be/fiche/PB00109450.html
Bijlage Portfolio Netwerk 3
Router(config)#interface Fa0/0
Router(config-if)#ip address 10.10.10.1 255.255.255.248
Router(config-if)#no shutdown
17
Configure the hostname of the switch as Switch1. Switch>enable
Switch#configure terminal
Switch(config)#hostname Switch1
Set the privileged EXEC mode password to cisco Switch1(config)#enable password cisco
Set the privileged EXEC mode secret password to class Switch1(config)#enable secret class
Configure the console and virtual terminal lines to use a password and
require it at login. Switch1(config)#line console 0
Switch1(config-line)#password cisco
Switch1(config-line)#login
Switch1(config-line)#line vty 0 15
Switch1(config-line)#password cisco
Switch1(config-line)#login
Switch1(config-line)#end
Enter the interface configuration mode for VLAN 1. Switch1(config)#interface vlan 1
Switch1(config-if)#ip address 192.168.1.5 255.255.255.0
Switch1(config-if)#no shutdown
Switch1(config-if)#exit
Switch1(config)#ip default-gateway 192.168.1.
R1(config)#banner motd + ************************************************** Authorized Users Only! ************************************************** +
Configure the FastEthernet 0/0 interface with the IP address
192.168.1.1/24. R1(config)#interface fastethernet 0/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no shutdown
Configure the Serial 0/0/0 interface with the IP address
192.168.2.1/24. Set the clock rate to 64000. R1(config-if)#interface serial 0/0/0
R1(config-if)#ip address 192.168.2.1 255.255.255.0
R1(config-if)#clock rate 64000
R1(config-if)#no shutdown
Create a static route to enable R1 to reach the network attached to the R2 Fa0/0 interface. Use the next hop interface on R2 as the path to this network.
18
R1(config)#ip route 192.168.3.0 255.255.255.0 192.168.2.2
Perform basic configuration of router R2 R2(config)#interface serial 0/0/0
R2(config-if)#ip address 192.168.2.2 255.255.255.0
R2(config-if)#no shutdown
Configure the FastEthernet 0/0 interface with the IP address
192.168.3.1/24. R2(config-if)#interface fastethernet 0/0
R2(config-if)#ip address 192.168.3.1 255.255.255.0
R2(config-if)#no shutdown
R2(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.1
Remove the static route to 192.168.3.0. R1(config)#no ip route 192.168.3.0 255.255.255.0 192.168.2.2
Enable RIP v2 routing and advertise the participating networks. R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#network 192.168.1.0
R1(config-router)#network 192.168.2.0
Remove the static route to 192.168.1.0 R2(config)#noip route 192.168.1.0 255.255.255.0 192.168.2.1
Enable RIP v2 routing and advertise the participating networks. R2(config)#router rip
R2(config-router)#version 2
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.3.0
To allow the switch port FastEthernet 0/1 to accept only one device,
configure port security as follows: Switch1(config)#interface fastethernet 0/1
Switch1(config-if)#switchport mode access
Switch1(config-if)#switchport port-security
Switch1(config-if)#switchport port-security mac-address sticky
Switch1(config-if)#end
View the show mac-address-table options View the options that the show mac-address-table command has available. Switch1(config)#show mac-address-table ?
Set up a static MAC address on FastEthernet interface 0/4. Use the address that was recorded for PC2 in Step 9. The MAC address 00e0.2917.1884 is used in this example statement only. Switch1(config)#mac-address-table static 00e0.2917.1884 vlan 1
19
interface fastethernet 0/4
On interface FastEthernet 0/4, set the port security maximum MAC count to 1. Switch1(config-if)#switchport port-security maximum 1
In the event of a security violation, the interface should be shut down. To make the port security shut down, enter the following command: Switch1(config-if)#switchport port-security violation shutdown
Check the port security settings. Switch1#show port-security
Disable unused ports Disable any ports not being used on the switch. Switch1(config)#interface range Fa0/2 – 3
Switch1(config-if-range)#shutdown
Switch1(config-if-range)#exit
Switch1(config)#interface range Fa0/5 – 24
Switch1(config-if-range)#shutdown
Switch1(config)#interface range gigabitethernet0/1 - 2
Switch1(config-if-range)#shutdown
Examine the spanning-tree tables on each switch SwitchA show spanning-tree
Determine the options that can be configured for the Spanning Tree
Protocol by issuing this command: SwitchB(config)#spanning-tree ?
Set the priority of the switch to 4096.
20
SwitchB(config)#spanning-tree vlan 1 priority 4096
SwitchB(config)#exit
(config-if)#spanning-tree port-priority priority
console(config)# spanning-tree priority (VALEUR ENTRE 0 et 61440 par incréments de 4096)
By default, the port priority of an interface is 128. Lowering this value will ensure a specific interface becomes the Root Port: Switch(config)#int fa0/10 Switch(config-if)#spanning-tree port-priority 50 (dat is voor de kabel boss)
Configuring, Verifying, and Troubleshooting VLANs
21
S1(config)#interface vlan1
S1(config-if)#ip address 172.16.1.2 255.255.255.0
S1(config-if)#no shutdown
S1(config-if)#exit
S1(config)#ip default-gateway 172.16.1.1
Create and name two additional VLANs on S1. S1(config)#vlan 20
S1(config-vlan)#name fred
S1(config-vlan)#exit
S1(config)#vlan 30
S1(config-vlan)#name wilma
S1(config-vlan)#exit
Assign interfaces to VLANs. Assign S1 port Fa0/2 to VLAN 20 and ports Fa0/3 – Fa0/8 to VLAN 30. S1(config)#interface fastethernet 0/2
S1(config-if)#switchport mode access
S1(config-if)#switchport access vlan 20
S1(config-i f)#exit
S1(config)#interface range fastethernet 0/3 - 8
S1(config-if-range)#switchport mode access
S1(config-if-range)#switchport access vlan 30
S1(config-if-range)#end
S1#show vlan
S1#show vlan brief
S1#show vlan id 30
22
S1#show vlan name fred
Reassign S1 port Fa0/3 to VLAN 20. S1(config)#interface Fa0/3
S1(config-if)#switchport access vlan 20
S1(config)#end
S1#show vlan
Creating VLANs and Assigning Ports
Configure Switch 1 with the VLAN 1 IP address of 172.16.1.2/24. Switch1(config)#interface vlan1
Switch1(config-if)#ip address 172.16.1.2 255.255.255.0
Switch1(config-if)#no shutdown
Switch1(config-if)#exit
Create VLAN 10, named Faculty, and VLAN 20, named Students. Switch1(config)#vlan 10
Switch1(config-vlan)#name Faculty
Switch1(config-vlan)#exit
Switch1(config)#vlan 20
Switch1(config-vlan)#name Students
Switch1(config-vlan)#exit
23
Configure Switch 1 with thedefault gateway address of 172.16.1.1. Switch1(config)#ip default-gateway 172.16.1.1
Configure Switch 1 to place interfaces Fa0/5 and Fa0/6 in VLAN 10. Switch1(config)#interface Fa0/5
Switch1(config-if)#switchport mode access
Switch1(config-if)#switchport access vlan 10
Switch1(config-if)#interface Fa0/6
Switch1(config-if)#switchport mode access
Switch1(config-if)#switchport access vlan 10
Switch1(config-if)#exit
Configure Switch 1 to place interfaces Fa0/7 and Fa0/8 in VLAN 20. Switch1(config)#interface Fa0/7
Switch1(config-if)#switchport mode access
Switch1(config-if)#switchport access vlan 20
Switch1(config-if)#interface Fa0/8
Switch1(config-if)#switchport mode access
Switch1(config-if)#switchport access vlan 20
Switch1(config-if)#end
Configuring a Trunk Port to Connect Switches
S1(config)#interface fa0/1
S1(config-if)#switchport mode access
24
S2(config)#interface fa0/1
S2(config-if)#switchport mode access
To allow connectivity within multiple VLANs across multiple switches, trunking can be
configured. Without trunking, each VLAN requires a separate physical connection
between switches
S1(config)#int Fa0/1
S1(config-if)#switchport mode trunk
S1(config-if)#end
S2(config)#int Fa0/1
S2(config-if)#switchport mode trunk
S2(config-if)#end
(Main#show ip interface brief)
On R1, configure RIP version 2 as the routing protocol and advertise the appropriate networks: R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#network 172.16.1.0
R1(config-router)#network 172.16.3.0
From the R3 router to the host simulating the Internet, create a static route to network 0.0.0.0 0.0.0.0,
using the ip route command. This will forward any unknown-destination address traffic to the PC
simulating the Internet by setting a Gateway of Last Resort on the R3 router.
25
R3(config)#ip route 0.0.0.0 0.0.0.0 209.165.201.2
R3 will advertise this route to the other routers if this command is added to its RIP configuration: R3(config)#router rip
R3(config-router)#default-information originate
Implementing EIGRP
On Gateway, configure EIGRP as the routing protocol with an autonomous system number of 100, and advertise the appropriate networks. Gateway(config)#router eigrp 100
Gateway(config-router)#network 10.0.0.0
Gateway(config-router)#network 10.0.0.4
On Branch1, configure EIGRP as the routing protocol with an autonomous system number of 100, and advertise the appropriate networks: Branch1(config)#router eigrp 100
Branch1(config-router)#network 10.0.0.0
26
Branch1(config-router)#network 10.0.0.8
Branch1(config-router)#network 172.16.0.0
Branch1(config-router)#network 172.16.1.0
Branch1(config-router)#network 172.16.2.0
Branch1(config-router)#network 172.16.3.0
On each of the three routers, remove automatic summarization to force EIGRP to report all subnets. A sample command is given for Gateway. Gateway(config)#router eigrp 100
Gateway(config-router)# no auto-summary
On Branch2, configure manual summarization to force EIGRP to summarize only the 172.17.0.0 and 172.17.1.0 subnets Branch2(config)#interface s0/0/0
Branch2(config-if)#ip summary-address eigrp 100 172.17.0.0 255.255.252.0
Branch2(config)#interface s0/0/1
Branch2(config-if)#ip summary-address eigrp 100 172.17.0.0 255.255.252.0
Configuring and Verifying Single Area OSPF
Configure an OSPF routingprocess on router R1. Use OSPF process number 1and ensure that all networks are in Area 0. R1(config)#router ospf 1
R1(config-router)#network 192.168.1.128 0.0.0.63 area 0
R1(config-router)#network 192.168.15.0 0.0.0.3 area 0
27
R1(config-router)#end
R1(config)#router ospf 1
R1(config-router)#log-adjacency-changes
R1(config-router)#end
Configure an OSPF routing process on router R2. Use OSPF process number 1 and ensure that all networks are in Area 0. R2(config)#router ospf 1
R2(config-router)#network 192.168.0.0 0.0.0.255 area 0
R2(config-router)#network 192.168.15.0 0.0.0.3 area 0
R2(config-router)#end
R2(config)#router ospf 1
R2(config-router)#log-adjacency-changes
R2(config-router)#end
Configuring OSPF authentication is a two-step process. First, it is enabledon arouter for an area, and then it is configured on the interfacesin that area. a. Enable MD5 authentication in Area 0 onboth routers. R1(config)#router ospf 1
R1(config-router)#area 0 authentication message-digest
R2(config)#router ospf 1
R2(config-router)#area 0 authentication message-digest
Enable OSPFauthentication on S0/0/0 of R1. R1(config)#interface s0/0/0
R1(config-if)#ip ospf message-digest-key 10 md5 secretpassword
Enable OSPFauthentication on S0/0/0 of R2. R2(config)#interface s0/0/0
R2(config-if)#ip ospf message-digest-key 10 md5 secretpassword
28
Configure serial and loopback interfaces on Router 3. R3(config)#interface s0/0/1
R3(config-if)#ip address 200.20.20.1 255.255.255.252
R3(config-if)#clock rate 64000
R3(config-if)#no shutdown
R3(config-if)#interface lo0
R3(config-if)#ip address 138.25.6.33 255.255.255.255
R3(config-if)#exit
On Router 3, configure a default route toboth the 192.168.0.0 and the 192.168.1.0 networks. R3(config)#ip route 192.168.1.0 255.255.255.0 200.20.20.2
R3(config)#ip route 192.168.0.0 255.255.255.0 200.20.20.2
Configure loopback, FastEthernet, and serial interfaces on Router 1 and Router 2. R1(config)#interface loopback 0
R1(config-if)#ip address 192.168.31.11 255.255.255.255
R1(config-if)#interface serial 0/0/0
R1(config-if)#ip address 192.168.1.1 255.255.255.252
R1(config-if)#clock rate 64000
R1(config-if)#no shutdown
R1(config-if)#interface fa 0/0
29
R1(config-if)#ip address 192.168.1.129 255.255.255.192
R1(config-if)#no shutdown
R2(config)#interface loopback 0
R2(config-if)#ip address 192.168.31.22 255.255.255.255
R2(config-if)#interface serial 0/0/0
R2(config-if)#ip address 192.168.1.2 255.255.255.252
R2(config-if)#no shutdown
R2(config-if)#interface serial 0/0/1
R2(config-if)#ip address 200.20.20.2 255.255.255.252
R2(config-if)#no shutdown
R2(config-if)#interface fa 0/0
R2(config-if)#ip address 192.168.0.1 255.255.255.0
R2(config-if)#no shutdown
Configure OSPF routing on each router. Use OSPF process number 1 and ensure that all networks are in Area 0. R1(config)#router ospf 1 R1(config-router)#network 192.168.1.128 0.0.0.127 area 0
R1(config-router)#network 192.168.1.0 0.0.0.3 area 0
R2(config)#router ospf 1
R2(config-router)#network 192.168.0.0 0.0.0.255 area 0
R2(config-router)#network 192.168.1.0 0.0.0.3 area 0
On R2 only, enter a static default route. R2(config)#ip route 0.0.0.0 0.0.0.0 200.20.20.1
Propagate the gateway of last resort tothe other routers in the OSPF domain. At the configure router
prompt on R2, enter default-information originate.
R2(config-router)#default-information originate