Post on 05-Jul-2015
BOEKENHOUDER 1.6
http://designforeveryone.howest.be/
Maarten Van Overbeke / Jasmien Decancq
2 hours and 5 minutes€ 80
http://boekenhouder2012.blogspot.com/
ASSEMBLY MANUAL
http://designforeveryone.howest.be/
BILL OF MATERIAL- 1 MDF sheets (2440x500x12mm): € 15- 1 Plexiglas sheet (600x450x6mm): € 5- 2 Locking spring clips: € 0.10- mouthpiece: € 4.50- ALU extrusion profile(100xØ10mm): 1.5 €- adhesive magnetic tape: 4,45 €- double-sided tape: 4,99 €- anti-slip plastic: 3 €- acrylic foam double sided tape: 2.99 €- nylon wire: 2.45 €
BOEKENHOUDER 1.6
Tools: metal saw, hand drill, drill bit Ø2.5mm,sandpaper 180 grit, cutter knife
Standard parts: 2 Locking spring clips
Tailored parts: MDF and Plexiglas sheet
1DESCRIPTION Search for someone
who has a laser cutting machine. Buy theplexiglas and mdf sheet. Dowload file_plexiglasand file_mdf, those are available on our blog.Put them on a USB-stick and deliver it to personwith the laser cutter machine. A few days lateryou will receive your lasered parts.
BOEKENHOUDER 1.6
Technical plan: part files on our blog
Duration time lasering: 1 hour
Laser cutting machine
Standard parts: no
Tailored parts: mouth piece, 2 reading sheets, 2 sided parts, intermediate piece, 2 small parts and one slide part. Action cost: 30 €
2 BOEKENHOUDER 1.6
DESCRIPTION Rub all of the MDF
surfaces with sandpaper until they are smoothenough, so you will not harm yourself while youassemble the product.
Technical plan: no
Duration time: 15 minutes
Sandpaper 180 grit
Standard parts: no
Tailored parts: 2 sided parts, 1 intermediate piece and 2 small parts Action cost: no
3DESCRIPTION Indicate the positioin
of the tape with a pencil. Cut the adhesivemagnet tape into pieces and glue it onto thewood.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 minutes
Magnetic tape
Standard parts: no
Tailored parts: intermediate piece
Action cost: no
4DESCRIPTION Cut the adhesive
magnet tape to the correct length and paste itonto the end of the Plexiglas strip.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 minutes
Magnetic tape
Standard parts: no
Tailored parts: 2 reading sheet
Action cost: no
5DESCRIPTION Cut the double-sided
tape to the correct length and paste it onto theheat shrink thick wall.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 2 minutes
Dubble-sided tape
Standard parts: no
Tailored parts: no
Action cost: no
6DESCRIPTION Stick it onto the MDF
wood.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 5 minutes
Double-sided tape
Standard parts: no
Tailored parts: 2 MDF small parts
Action cost: no
7DESCRIPTION Cut the aluminium
extrusion profile with a metal saw. The length ofthis tubes is about 60mm.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 5 minutes
Metal saw
Standard parts: ALU extrusion profile(100xØ10mm):Tailored parts: no
Action cost: no
8DESCRIPTION Take your hand drill
with a drill bit size 2.5mm. Drill two holes intothe tubes. At both sides at a distance of 10mm.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 5 minutes
Hand drill, drill bit 2.5mm
Standard parts: ALU extrusion profile
Tailored parts: no
Action cost: no
9DESCRIPTION Cut the nylon wire at a
length of minium 500mm.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 30 seconds
Cutter knife
Standard parts: nylon wire
Tailored parts: no
Action cost: no
10DESCRIPTION Tie the nylon wire
through the hole of the aluminium extrusionprofile. Do the same with the other end of thewire.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 1 minute
No
Standard parts: ALU extrusion profile
Tailored parts: no
Action cost: no
11DESCRIPTION Cut the anti-slip plastic
at a length of 50mm and width of 8mm.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 1 minute
Cutter knife, ruler
Standard parts: anti-slip plastic
Tailored parts: no
Action cost: no
12DESCRIPTION Cut 2 strips of double-
sided tape at a length of 10mm and width of6mm. Depending on which size of tape you use.
Attention!We use an acrylic foam tape double-sided tapebecause of it’s sustainability.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 1 minute
Cutter knife, ruler
Standard parts: acrylic foam double-sided tape
Tailored parts: no
Action cost: no
13DESCRIPTION Stick the two cutted
parts of acrylic foam tape on each side of thelaser cutted mouthpiece, as shown on thepicture. On top of that, you stick the anti-slipplastic.
Attention!There has to be some space in between theanti-slip plastic and the laser cuttedmouthpiece, this ensures more grip onto thepaper.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 5 minute
No
Standard parts: no
Tailored parts: laser cutted mouthpart, parts of page 11 and 12Action cost: no
14DESCRIPTION Buy a mouthpiece and
cut the edges from it. This provides morecomfort for the user.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 3 minute
Cutting knife
Standard parts: mouthpiece
Tailored parts: no
Action cost: no
15DESCRIPTION Put the rubber
mouthpiece onto the laser cutted mouth piece.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 5 seconds
Cutting knife
Standard parts: Plexiglas mouth piece and rubbber mouthpieceTailored parts: no
Action cost: no
16DESCRIPTION Once the mouthpiece
has been assembled you can start with thebookreader. Take the intermediate MDF partand slide it into one sided MDF part.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
No
Standard parts: No
Tailored parts: one sided mdf part and the intermediate mdf partAction cost: no
17DESCRIPTION Take the other sided
part and slided it into the intermediate part.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
No
Standard parts: No
Tailored parts: one sided mdf part and the intermediate mdf partAction cost: no
18DESCRIPTION Take the slide MDF
part and slide it into the appropriiate holes, onthe back of the bookreader.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
No
Standard parts: No
Tailored parts: slide MDF part
Action cost: no
19DESCRIPTION Take the small MDF
parts and slide them into the appropriiate holes,in the intermediate MDF part.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
No
Standard parts: No
Tailored parts: 2 small MDF parts
Action cost: no
20DESCRIPTION Slide the cutted
aluminium extrusion tube into the cutted holeand insert the locking spring clip. Do the same atthe other side.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
No
Standard parts: No
Tailored parts: 2 small MDF parts, 2 locking spring clips and 2 alu extrusion tubes with nylon wire
Action cost: no
21DESCRIPTION Lay the Plexiglas book
reader sheets onto the magnetic strip.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
No
Standard parts: No
Tailored parts: 2 Plexiglas bookreader sheets
Action cost: no
22DESCRIPTION Open your book and
lay it onto the nylon wire. Next, set the bookreader sliders onto the appropriate distance.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
Book
Standard parts: No
Tailored parts: No
Action cost: no
23DESCRIPTION Hang up the
mouthpiece between the intermediate part andthe book. This ensures that the reader doesn’thave to put the mouthpiece continuously intohis mouth while reading.
BOEKENHOUDER 1.6
Technical plan: no
Duration time: 10 seconds
Book
Standard parts: No
Tailored parts: No
Action cost: no
24 BOEKENHOUDER 1.6
TECHNICAL ADDENDUM
http://designforeveryone.howest.be/
Material: MDF wood File: Inter_mdf.pdf
#UNITS: 1 Boekenhouder 1.6
HOWEST Date: 04/06/2012
Intermediate part
Material: MDF wood File: Side_mdf.pdf
#UNITS: 2 Boekenhouder 1.6
HOWEST Date: 04/06/2012
Side part
Material: MDF wood File: Small_mdf.pdf
#UNITS: 2 Book Holder 1.6
HOWEST Date: 04/06/2012
Small part
Material: MDF wood File: Slide_mdf.pdf
#UNITS: 2 Book Holder 1.6
HOWEST Date: 04/06/2012
Slide part
Material: Plexiglas File: Reader_plexiglas.pdf
#UNITS: 2 Book Holder 1.6
HOWEST Date: 04/06/2012
Book reader
TEAM CONTACTS
http://designforeveryone.howest.be/
VANOVERBEKE.MAARTEN@GMAIL.COMTEL +32 4 75 47 81 50
JASMIENDECANCQ@GMAIL.COMTEL +32 4 85 25 29 87
KYLIE.BIESBROUCK @HOWEST.BETEL +32 4 76 41 30 95
http://designforeveryone.howest.be/