Handleiding boekenhouder 1.6

http://designforeveryone.howest.be/

http://creativecommons.org/licenses/by-nc-sa/3.0/nl/

BOEKENHOUDER 1.6


Maarten Van Overbeke / Jasmien Decancq

2 hours and 5 minutes€ 80

http://boekenhouder2012.blogspot.com/


ASSEMBLY MANUAL



BILL OF MATERIAL- 1 MDF sheets (2440x500x12mm): € 15- 1 Plexiglas sheet (600x450x6mm): € 5- 2 Locking spring clips: € 0.10- mouthpiece: € 4.50- ALU extrusion profile(100xØ10mm): 1.5 €- adhesive magnetic tape: 4,45 €- double-sided tape: 4,99 €- anti-slip plastic: 3 €- acrylic foam double sided tape: 2.99 €- nylon wire: 2.45 €

BOEKENHOUDER 1.6

Tools: metal saw, hand drill, drill bit Ø2.5mm,sandpaper 180 grit, cutter knife

Standard parts: 2 Locking spring clips

Tailored parts: MDF and Plexiglas sheet

1DESCRIPTION Search for someone

who has a laser cutting machine. Buy theplexiglas and mdf sheet. Dowload file_plexiglasand file_mdf, those are available on our blog.Put them on a USB-stick and deliver it to personwith the laser cutter machine. A few days lateryou will receive your lasered parts.

BOEKENHOUDER 1.6

Technical plan: part files on our blog

Duration time lasering: 1 hour

Laser cutting machine

Standard parts: no

Tailored parts: mouth piece, 2 reading sheets, 2 sided parts, intermediate piece, 2 small parts and one slide part. Action cost: 30 €

2 BOEKENHOUDER 1.6

DESCRIPTION Rub all of the MDF

surfaces with sandpaper until they are smoothenough, so you will not harm yourself while youassemble the product.

Technical plan: no

Duration time: 15 minutes

Sandpaper 180 grit

Standard parts: no

Tailored parts: 2 sided parts, 1 intermediate piece and 2 small parts Action cost: no

3DESCRIPTION Indicate the positioin

of the tape with a pencil. Cut the adhesivemagnet tape into pieces and glue it onto thewood.

BOEKENHOUDER 1.6

Technical plan: no


Magnetic tape

Standard parts: no

Tailored parts: intermediate piece

Action cost: no

4DESCRIPTION Cut the adhesive

magnet tape to the correct length and paste itonto the end of the Plexiglas strip.

BOEKENHOUDER 1.6

Technical plan: no


Magnetic tape

Standard parts: no

Tailored parts: 2 reading sheet

Action cost: no

5DESCRIPTION Cut the double-sided

tape to the correct length and paste it onto theheat shrink thick wall.

BOEKENHOUDER 1.6

Technical plan: no


Dubble-sided tape

Standard parts: no

Tailored parts: no

Action cost: no

6DESCRIPTION Stick it onto the MDF

wood.

BOEKENHOUDER 1.6

Technical plan: no


Double-sided tape

Standard parts: no

Tailored parts: 2 MDF small parts

Action cost: no

7DESCRIPTION Cut the aluminium

extrusion profile with a metal saw. The length ofthis tubes is about 60mm.

BOEKENHOUDER 1.6

Technical plan: no


Metal saw

Standard parts: ALU extrusion profile(100xØ10mm):Tailored parts: no

Action cost: no

8DESCRIPTION Take your hand drill

with a drill bit size 2.5mm. Drill two holes intothe tubes. At both sides at a distance of 10mm.

BOEKENHOUDER 1.6

Technical plan: no


Hand drill, drill bit 2.5mm

Standard parts: ALU extrusion profile

Tailored parts: no

Action cost: no

9DESCRIPTION Cut the nylon wire at a

length of minium 500mm.

BOEKENHOUDER 1.6

Technical plan: no

Duration time: 30 seconds

Cutter knife

Standard parts: nylon wire

Tailored parts: no

Action cost: no

10DESCRIPTION Tie the nylon wire

through the hole of the aluminium extrusionprofile. Do the same with the other end of thewire.

BOEKENHOUDER 1.6

Technical plan: no

Duration time: 1 minute

No

Standard parts: ALU extrusion profile

Tailored parts: no

Action cost: no

11DESCRIPTION Cut the anti-slip plastic

at a length of 50mm and width of 8mm.

BOEKENHOUDER 1.6

Technical plan: no


Cutter knife, ruler

Standard parts: anti-slip plastic

Tailored parts: no

Action cost: no

12DESCRIPTION Cut 2 strips of double-

sided tape at a length of 10mm and width of6mm. Depending on which size of tape you use.

Attention!We use an acrylic foam tape double-sided tapebecause of it’s sustainability.

BOEKENHOUDER 1.6

Technical plan: no


Cutter knife, ruler

Standard parts: acrylic foam double-sided tape

Tailored parts: no

Action cost: no

13DESCRIPTION Stick the two cutted

parts of acrylic foam tape on each side of thelaser cutted mouthpiece, as shown on thepicture. On top of that, you stick the anti-slipplastic.

Attention!There has to be some space in between theanti-slip plastic and the laser cuttedmouthpiece, this ensures more grip onto thepaper.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: no

Tailored parts: laser cutted mouthpart, parts of page 11 and 12Action cost: no

14DESCRIPTION Buy a mouthpiece and

cut the edges from it. This provides morecomfort for the user.

BOEKENHOUDER 1.6

Technical plan: no


Cutting knife

Standard parts: mouthpiece

Tailored parts: no

Action cost: no

15DESCRIPTION Put the rubber

mouthpiece onto the laser cutted mouth piece.

BOEKENHOUDER 1.6

Technical plan: no


Cutting knife

Standard parts: Plexiglas mouth piece and rubbber mouthpieceTailored parts: no

Action cost: no

16DESCRIPTION Once the mouthpiece

has been assembled you can start with thebookreader. Take the intermediate MDF partand slide it into one sided MDF part.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: No

Tailored parts: one sided mdf part and the intermediate mdf partAction cost: no

17DESCRIPTION Take the other sided

part and slided it into the intermediate part.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: No

Tailored parts: one sided mdf part and the intermediate mdf partAction cost: no

18DESCRIPTION Take the slide MDF

part and slide it into the appropriiate holes, onthe back of the bookreader.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: No

Tailored parts: slide MDF part

Action cost: no

19DESCRIPTION Take the small MDF

parts and slide them into the appropriiate holes,in the intermediate MDF part.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: No

Tailored parts: 2 small MDF parts

Action cost: no

20DESCRIPTION Slide the cutted

aluminium extrusion tube into the cutted holeand insert the locking spring clip. Do the same atthe other side.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: No

Tailored parts: 2 small MDF parts, 2 locking spring clips and 2 alu extrusion tubes with nylon wire

Action cost: no

21DESCRIPTION Lay the Plexiglas book

reader sheets onto the magnetic strip.

BOEKENHOUDER 1.6

Technical plan: no


No

Standard parts: No

Tailored parts: 2 Plexiglas bookreader sheets

Action cost: no

22DESCRIPTION Open your book and

lay it onto the nylon wire. Next, set the bookreader sliders onto the appropriate distance.

BOEKENHOUDER 1.6

Technical plan: no


Book

Standard parts: No

Tailored parts: No

Action cost: no

23DESCRIPTION Hang up the

mouthpiece between the intermediate part andthe book. This ensures that the reader doesn’thave to put the mouthpiece continuously intohis mouth while reading.

BOEKENHOUDER 1.6

Technical plan: no


Book

Standard parts: No

Tailored parts: No

Action cost: no

24 BOEKENHOUDER 1.6

TECHNICAL ADDENDUM



Material: MDF wood File: Inter_mdf.pdf

#UNITS: 1 Boekenhouder 1.6

HOWEST Date: 04/06/2012

Intermediate part

Material: MDF wood File: Side_mdf.pdf

#UNITS: 2 Boekenhouder 1.6


Side part

Material: MDF wood File: Small_mdf.pdf

#UNITS: 2 Book Holder 1.6


Small part

Material: MDF wood File: Slide_mdf.pdf



Slide part

Material: Plexiglas File: Reader_plexiglas.pdf



Book reader

TEAM CONTACTS



[email protected] +32 4 75 47 81 50

[email protected] +32 4 85 25 29 87

KYLIE.BIESBROUCK @HOWEST.BETEL +32 4 76 41 30 95



Handleiding boekenhouder 1.6

Business

Transcript of Handleiding boekenhouder 1.6