Voorbeeld Preview - NEN · TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN ISO/TR 20173...
Transcript of Voorbeeld Preview - NEN · TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN ISO/TR 20173...
Nederlandse praktijkrichtlijn
NPR-CEN-ISO/TR 20173
(en) Welding - Grouping systems for materials -
American materials (ISO/TR 20173:2009,IDT)
Vervangt NPR-CEN-ISO/TR 20173:2006
ICS 25.160.20
oktober 2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Dit
do
cum
ent
mag
sle
chts
op
een
sta
nd
-alo
ne
PC
wo
rden
gei
nst
alle
erd
. Geb
ruik
op
een
net
wer
k is
alle
en.
toes
taan
als
een
aan
vulle
nd
e lic
enti
eove
reen
kom
st v
oo
r n
etw
erkg
ebru
ik m
et N
EN
is a
fges
lote
n.
Th
is d
ocu
men
t m
ay o
nly
be
use
d o
n a
sta
nd
-alo
ne
PC
. Use
in a
net
wo
rk is
on
ly p
erm
itte
d w
hen
a su
pp
lem
enta
ry li
cen
se a
gre
emen
t fo
r u
s in
a n
etw
ork
wit
h N
EN
has
bee
n c
on
clu
ded
.
NPR-CEN-ISO/TR 20173
Als Nederlandse praktijkrichtlijn is aanvaard: - CEN ISO/TR 20173:2009,IDT - ISO/TR 20173:2009,IDT
Normcommissie 341008 "Lassen en verwante processen" Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation.
Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute.
Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht.
Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven.
©2009 Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) 2 690 390, Fax (015) 2 690 190
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
TECHNICAL REPORT
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
CEN ISO/TR 20173
October 2009
ICS 25.160.20 Supersedes CEN ISO/TR 20173:2005
English Version
Welding - Grouping systems for materials - American materials (ISO/TR 20173:2009)
Soudage - Systèmes de groupement des matériaux - Matériaux américains (ISO/TR 20173:2009)
Schweißen - Werkstoffgruppeneinteilung - Amerikanische Werkstoffe (ISO/TR 20173:2009)
This Technical Report was approved by CEN on 15 September 2009. It has been drawn up by the Technical Committee CEN/TC 121. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T É E U R O P É E N D E N O R M A LI S A T I O N EUR OP ÄIS C HES KOM ITEE FÜR NOR M UNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
Ref. No. CEN ISO/TR 20173:2009: E
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
CEN ISO/TR 20173:2009 (E)
2
Contents Page
Foreword ..............................................................................................................................................................3
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
CEN ISO/TR 20173:2009 (E)
3
Foreword
This document (CEN ISO/TR 20173:2009) has been prepared by Technical Committee ISO/TC 44 "Welding and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TR 20173:2005.
Endorsement notice
The text of ISO/TR 20173:2009 has been approved by CEN as a CEN ISO/TR 20173:2009 without any modification.
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Reference numberISO/TR 20173:2009(E)
© ISO 2009
TECHNICAL REPORT
ISO/TR20173
Second edition2009-10-01
Welding — Grouping systems for materials — American materials
Soudage — Systèmes de groupement des matériaux — Matériaux américains
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
ISO/TR 20173:2009(E)
PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT © ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.
ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
ISO/TR 20173:2009(E)
© ISO 2009 – All rights reserved iii
Contents Page
Foreword............................................................................................................................................................ iv 1 Scope ..................................................................................................................................................... 1 2 American grouping system for materials........................................................................................... 1 Bibliography ..................................................................................................................................................... 58
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
ISO/TR 20173:2009(E)
iv © ISO 2009 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
In exceptional circumstances, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example), it may decide by a simple majority vote of its participating members to publish a Technical Report. A Technical Report is entirely informative in nature and does not have to be reviewed until the data it provides are considered to be no longer valid or useful.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TR 20173 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding.
This second edition cancels and replaces the first edition (ISO/TR 20173:2005), which has been technically revised.
Requests for official interpretations of any aspect of this Technical Report should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete listing of these bodies can be found at http://www.iso.org.
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
TECHNICAL REPORT ISO/TR 20173:2009(E)
© ISO 2009 – All rights reserved 1
Welding — Grouping systems for materials — American materials
1 Scope
This Technical Report provides an American grouping system for materials for welding purposes, classified in accordance with the grouping system of ISO/TR 15608:2005[1].
It may also apply for other purposes, such as heat treatment, forming, and non-destructive testing. Types of steels are listed in accordance with the grouping system of ISO/TR 15608:2005[1], Table 1.
This Technical Report covers grouping systems for the following standardized materials:
⎯ steel;
⎯ aluminium and its alloys;
⎯ nickel and its alloys;
⎯ copper and its alloys;
⎯ titanium and its alloys;
⎯ zirconium and its alloys;
⎯ cast irons.
2 American grouping system for materials
See Tables 1 and 2.
Table 1 — American grouping system for ferrous material
ASTM/ASME ASME/AWS
Specification No. Type or grade UNS
No. P or MNo.
GroupNo.
ISO/TR 15608:2005[1]
group Nominal composition
AS 15 5-490 — 1 — 1.1 C
AS 15 7-430 — 1 — 1.1 C
AS 15 7-460 — 1 — 1.1 C
AS 15 7-490 — 1 — 1.1 C
A/SA 36 — K02600 1 1 11.1 C-Mn-Si
A/SA 36 — K02600 1 1 11.1 C-Mn-Si
A/SA 53 Type E, Gr. A K02504 1 1 11.1 C
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
ISO/TR 20173:2009(E)
2 © ISO 2009 – All rights reserved
Table 1 (continued)
ASTM/ASME ASME/AWS
Specification No. Type or grade UNS
No. P or MNo.
GroupNo.
ISO/TR 15608:2005[1]
group Nominal composition
A/SA 53 Type E, Gr. B K03005 1 1 11.1 C-Mn
A/SA 53 Type F — 1 1 11.1 C
A/SA 53 Type S, Gr. A K02504 1 1 11.1 C
A/SA 53 Type S, Gr. B K03005 1 1 11.1 C-Mn
A/SA 105 — K03504 1 2 11.1 C
A/SA 106 A K02501 1 1 1.1 C-Si
A/SA 106 B K03006 1 1 11.1 C-Mn-Si
A/SA 106 C K03501 1 2 11.1 C-Mn-Si
A 108 1015 CW G10150 1 1 1.1 C
A 108 1018 CW G10180 1 1 1.1 C
A 108 1020 CW G10200 1 1 1.1 C
A 108 8620 CW G86200 3 3 4.1 0.5Ni-0.5Cr-Mo
A 131 A — 1 1 1.1 C
A 131 AH32 — 1 2 1.2 C-Mn-Si
A 131 AH36 — 1 2 1.2 C-Mn-Si
A 131 B — 1 1 1.1 C-Mn-Si
A 131 CS — 1 1 1.1 C-Mn-Si
A 131 D — 1 1 1.1 C-Mn-Si
A 131 DH32 — 1 2 1.2 C-Mn-Si
A 131 DH36 — 1 2 1.2 C-Mn-Si
A 131 DS — 1 1 1.1 C-Mn-Si
A 131 E — 1 2 1.1 C-Mn-Si
A 131 EH32 — 1 2 1.2 C-Mn-Si
A 131 EH36 — 1 2 1.2 C-Mn-Si
A/SA 134 SA283, Gr. A — 1 1 1.1 C
A/SA 134 SA283, Gr. B — 1 1 1.1 C
A/SA 134 SA283, Gr. C K02401 1 1 1.1 C
A/SA 134 SA283, Gr. D K02702 1 1 1.1 C
A/SA 134 SA285, Gr. A K01700 1 1 1.1 C
A/SA 134 SA285, Gr. B K02200 1 1 1.1 C
A/SA 134 SA285, Gr. C K02801 1 1 11.1 C
A/SA 135 A — 1 1 1.1 C
A/SA 135 B — 1 1 11.1 C
A 139 A — 1 1 1.1 C
A 139 B K03003 1 1 1.1 C
NPR-CEN-ISO/TR 20173:2009
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
NEN Standards Products & Servicest.a.v. afdeling KlantenserviceAntwoordnummer 102142600 WB Delft
Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via www.nen.nl/normshop
Gratis e-mailnieuwsbrievenWilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen,
normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze
e-mailnieuwsbrieven. www.nen.nl/nieuwsbrieven
Gegevens Bedrijf / Instelling
T.a.v. O M O V
Klantnummer NEN
Uw ordernummer BTW nummer
Postbus / Adres
Postcode Plaats
Telefoon Fax
Factuuradres (indien dit afwijkt van bovenstaand adres)
Postbus / Adres
Postcode Plaats
Datum Handtekening
NEN Standards Products & Services
Postbus 50592600 GB Delft
Vlinderweg 62623 AX Delft
T (015) 2 690 390F (015) 2 690 271
www.nen.nl/normshop
RetournerenFax: (015) 2 690 271
E-mail: [email protected]
Post: NEN Standards Products
& Services,
t.a.v. afdeling Klantenservice
Antwoordnummer 10214,
2600 WB Delft
(geen postzegel nodig).
Voorwaarden• De prijzen zijn geldig
tot 31 december 2016,
tenzij anders aangegeven.
• Alle prijzen zijn excl. btw,
verzend- en handelingskosten
en onder voorbehoud bij
o.m. ISO- en IEC-normen.
• Bestelt u via de normshop een
pdf, dan betaalt u geen
handeling en verzendkosten.
• Meer informatie: telefoon
(015) 2 690 391, dagelijks
van 8.30 tot 17.00 uur.
• Wijzigingen en typefouten
in teksten en prijsinformatie
voorbehouden.
• U kunt onze algemene
voorwaarden terugvinden op:
www.nen.nl/leveringsvoorwaarden.
preview - 2016
Bestelformulier
Normalisatie: de wereld op één lijn.
Stuur naar:
Ja, ik bestel
€ 161.21__ ex. NPR-CEN-ISO/TR 20173:2009 en Lassen - Groepsindelingen voor
materialen - Amerikaanse materialen