Nederlandse NEN-ISO 128-34 · Nederlandse norm NEN-ISO 128-34 (en) Technische tekeningen - Algemene...

Nederlandse

norm

NEN-ISO 128-34 (en)

Technische tekeningen - Algemene principes voor de weergave - Deel 34: Aanzichten op werktuigbouwkundige tekeningen (ISO 128-34:2001,IDT)

Technical drawings - General principles of presentation - Part 34: Views on mechanical engineering drawings (ISO 128-34:2001,IDT)

februari 2001 ICS 01.100.20

Als Nederlandse norm is aanvaard: - ISO 128-34:2001,IDT

Normcommissie 400 007 "Technisch Productdocumentatie" Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation.

Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute.

Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht.

Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven.

©2001 Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) 2 690 390, Fax (015) 2 690 190

Voorbeeld

Preview

Dit document is een voorbeeld van NEN / This document is a preview by NEN

Dit

do

cum

ent

mag

sle

chts

op

een

sta

nd

-alo

ne

PC

wo

rden

gei

nst

alle

erd

. Geb

ruik

op

een

net

wer

k is

alle

en.

toes

taan

als

een

aan

vulle

nd

e lic

enti

eove

reen

kom

st v

oo

r n

etw

erkg

ebru

ik m

et N

EN

is a

fges

lote

n.

Th

is d

ocu

men

t m

ay o

nly

be

use

d o

n a

sta

nd

-alo

ne

PC

. Use

in a

net

wo

rk is

on

ly p

erm

itte

d w

hen

a su

pp

lem

enta

ry li

cen

se a

gre

emen

t fo

r u

s in

a n

etw

ork

wit

h N

EN

has

bee

n c

on

clu

ded

.

Voorbeeld

Preview


Reference numberISO 128-34:2001(E)

© ISO 2001

INTERNATIONALSTANDARD

ISO128-34

First edition2001-01-15

Technical drawings — General principles ofpresentation —

Part 34:Views on mechanical engineering drawings

Dessins techniques — Principes généraux de représentation —

Partie 34: Vues applicables aux dessins industriels

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


ISO 128-34:2001(E)

PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall notbe edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading thisfile, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in thisarea.

Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameterswere optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely eventthat a problem relating to it is found, please inform the Central Secretariat at the address given below.

© ISO 2001

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronicor mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member bodyin the country of the requester.

ISO copyright officeCase postale 56 � CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail [email protected] www.iso.ch

Printed in Switzerland

ii © ISO 2001 – All rights reserved

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


ISO 128-34:2001(E)

© ISO 2001 – All rights reserved iii

Contents Page

Foreword.....................................................................................................................................................................iv

1 Scope ..............................................................................................................................................................1

2 Normative references ....................................................................................................................................1

3 Terms and definitions ...................................................................................................................................1

4 Types of lines and their application.............................................................................................................2

5 Local views.....................................................................................................................................................2

6 Adjacent parts and contours ........................................................................................................................3

7 Intersections...................................................................................................................................................4

8 Square ends on shafts ..................................................................................................................................6

9 Interrupted views ...........................................................................................................................................6

10 Repeated features..........................................................................................................................................7

11 Enlarged features...........................................................................................................................................8

12 Initial outlines.................................................................................................................................................8

13 Bend lines.......................................................................................................................................................8

14 Slight inclines or curves ...............................................................................................................................9

15 Transparent objects ......................................................................................................................................9

16 Movable parts...............................................................................................................................................10

17 Finished parts and blanks ..........................................................................................................................11

18 Parts made from separate, equal elements ..............................................................................................11

19 Surface pattern.............................................................................................................................................12

20 Fibre and rolled directions..........................................................................................................................12

21 Parts with two or more identical views .....................................................................................................12

22 Mirror-image parts .......................................................................................................................................13

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


ISO 128-34:2001(E)

iv © ISO 2001 – All rights reserved

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISOmember bodies). The work of preparing International Standards is normally carried out through ISO technicalcommittees. Each member body interested in a subject for which a technical committee has been established hasthe right to be represented on that committee. International organizations, governmental and non-governmental, inliaison with ISO, also take part in the work. ISO collaborates closely with the International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.

Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this part of ISO 128 may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.

International Standard ISO 128-34 was prepared by Technical Committee ISO/TC 10, Technical productdocumentation, Subcommittee SC 6, Mechanical engineering documentation.

This first edition is based on ISO 128:1982, clause 5, and replaces the rules specified in that clause.

ISO 128 consists of the following parts, under the general title Technical drawings — General principles ofpresentation:

� Part 1: Introduction and index

� Part 20: Basic conventions for lines

� Part 21: Preparation of lines by CAD systems

� Part 22: Basic conventions and applications for leader lines and reference lines

� Part 23: Lines on construction drawings

� Part 24: Lines on mechanical engineering drawings

� Part 25: Lines on shipbuilding drawings

� Part 30: Basic conventions for views

� Part 34: Views on mechanical engineering drawings

� Part 40: Basic conventions for cuts and sections

� Part 44: Sections on mechanical engineering drawings

� Part 50: Basic conventions for representing areas on cuts and sections

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


INTERNATIONAL STANDARD ISO 128-34:2001(E)

© ISO 2001 – All rights reserved 1

Technical drawings — General principles of presentation —

Part 34:Views on mechanical engineering drawings

1 Scope

This part of ISO 128 specifies rules for the presentation of views additional to those of ISO 128-30 and applicableto mechanical engineering drawings that follow the orthographic projection methods specified in ISO 5456-2.Attention has also been given to reproduction requirements, including those of microcopying according toISO 6428.

2 Normative references

The following normative documents contain provisions which, through reference in this text, constitute provisions ofthis part of ISO 128. For dated references, subsequent amendments to, or revisions of, any of these publicationsdo not apply. However, parties to agreements based on this part of ISO 128 are encouraged to investigate thepossibility of applying the most recent editions of the normative documents indicated below. For undatedreferences, the latest edition of the normative document referred to applies. Members of ISO and IEC maintainregisters of currently valid International Standards.

ISO 128-20:1996, Technical drawings — General principles of presentation — Part 20: Basic conventions for lines.

ISO 128-24:1999, Technical drawings — General principles of presentation — Part 24: Lines on mechanicalengineering drawings.

ISO 128-30:—1�, Technical drawings — General principles of presentation — Part 30: Basic conventions for views.

ISO 129-1:—2), Technical drawings — Indication of dimensions and tolerances — Part 1: General principles.

ISO 5456-2:1996, Technical drawings — Projection methods — Part 2: Orthographic representations.

ISO 6428:1982, Technical drawings — Requirements for microcopying.

ISO 10209-1:1992, Technical product documentation — Vocabulary — Part 1: Terms relating to technicaldrawings: general and types of drawings.

3 Terms and definitions

For the purposes of this part of ISO 128, the terms and definitions given in ISO 10209-1 apply.

1� To be published.2) To be published. (Revision of ISO 129:1985)

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


ISO 128-34:2001(E)

2 © ISO 2001 – All rights reserved

4 Types of lines and their application

The basic types of lines referred to in this part of ISO 128 are specified in ISO 128-20. General rules and basicconventions for their application on mechanical engineering drawings are specified in ISO 128-24.

5 Local views

Provided presentation is unambiguous, a local rather than a complete view of symmetrical parts is permitted. Localviews should be drawn in third angle projection, regardless of the arrangement used for the general execution ofthe drawing. Local views shall be drawn with continuous wide lines (type 01.2) and connected to principal views bylong dashed dotted narrow lines (type 04.1). Examples are shown in Figures 1 to 4.

Figure 1 — Local view of journal

Figure 2 — Local view of groove

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


ISO 128-34:2001(E)

© ISO 2001 – All rights reserved 3

Figure 3 — Local view of hole

Figure 4 — Local view of groove

6 Adjacent parts and contours

Where parts adjacent to an object are presented, they shall be drawn with long dashed double-dotted narrow lines(type 05.1). The adjacent part shall not hide the principal part, but may be hidden by it (see Figure 5 and Figure 6).Adjacent parts in cuts and sections shall not be hatched.

Figure 5 — Bounded adjacent part

NEN-ISO 128-34:2001 en

Voorbeeld

Preview


NEN Standards Products & Servicest.a.v. afdeling KlantenserviceAntwoordnummer 102142600 WB Delft

Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via www.nen.nl/normshop

Gratis e-mailnieuwsbrievenWilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen,

normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze

e-mailnieuwsbrieven. www.nen.nl/nieuwsbrieven

Gegevens Bedrijf / Instelling

T.a.v. O M O V

E-mail

Klantnummer NEN

Uw ordernummer BTW nummer

Postbus / Adres

Postcode Plaats

Telefoon Fax

Factuuradres (indien dit afwijkt van bovenstaand adres)

Postbus / Adres

Postcode Plaats

Datum Handtekening

NEN Standards Products & Services

Postbus 50592600 GB Delft

Vlinderweg 62623 AX Delft

T (015) 2 690 390F (015) 2 690 271

www.nen.nl/normshop

RetournerenFax: (015) 2 690 271

E-mail: [email protected]

Post: NEN Standards Products

& Services,

t.a.v. afdeling Klantenservice

Antwoordnummer 10214,

2600 WB Delft

(geen postzegel nodig).

Voorwaarden• De prijzen zijn geldig

tot 31 december 2016,

tenzij anders aangegeven.

• Alle prijzen zijn excl. btw,

verzend- en handelingskosten

en onder voorbehoud bij

o.m. ISO- en IEC-normen.

• Bestelt u via de normshop een

pdf, dan betaalt u geen

handeling en verzendkosten.

• Meer informatie: telefoon

(015) 2 690 391, dagelijks

van 8.30 tot 17.00 uur.

• Wijzigingen en typefouten

in teksten en prijsinformatie

voorbehouden.

• U kunt onze algemene

voorwaarden terugvinden op:

www.nen.nl/leveringsvoorwaarden.

preview - 2016

Bestelformulier

Normalisatie: de wereld op één lijn.

Stuur naar:

Ja, ik bestel

€ 79.70__ ex. NEN-ISO 128-34:2001 en Technische tekeningen - Algemene

principes voor de weergave - Deel 34: Aanzichten op werktuigbouwkundige

tekeningen

Nederlandse NEN-ISO 128-34 · Nederlandse norm NEN-ISO 128-34 (en) Technische tekeningen - Algemene...

Documents

Transcript of Nederlandse NEN-ISO 128-34 · Nederlandse norm NEN-ISO 128-34 (en) Technische tekeningen - Algemene...