LG t7018aeep5
-
Upload
imthiyas-ahmed -
Category
Documents
-
view
216 -
download
0
Transcript of LG t7018aeep5
-
8/11/2019 LG t7018aeep5
1/37
Automatic Washing Machine
Owners Maintenance Manual
Note:
Please read this manual carefully before repairing your set.
Retain it for future reference.
Quote this information when you require maintenance.
Model: T7080)18AEEP5
1
-
8/11/2019 LG t7018aeep5
2/37
Contents
1. Safety Information. 3
2. Specification5
3. Features and Technical Instructions6
4. Identification of Parts. 10
5. Installation Guide. 11
6. Circuit diagram14
7. Washing program. 14
8. Introduction of Each Operation Button. 15
9. Dismantle Guide. . 17
10. Running Test. 22
11. Trouble shooting. . 23
12. Care and Maintenance. 26
13. Disassembly diagrams and parts list. 34
WarningSafety instruction! Unplug before maintenance
This maintenance manual is intended for professional maintenance
staff only.
Non-professional maintenance staffs are not allowed to disassemble
or maintain the machine.
2
-
8/11/2019 LG t7018aeep5
3/37
1.Safety information Read carefully
For your safety, the information in this manual must be followed to prevent property damage,personal injury. Save these instructions.
The following symbols are used for classification/Instruction of error use and content ignorance,
which would cause damage or injury.
Warning: possible serious damage or death when violating identity
matters.
Notice: possible minor serious damage or product operation when violating
identity matters.
Classification/Instruction with following symbols for people to obey. For example:
Marks which informs people of drawing attention to possible danger operation.
Marks which informs people of electric shock under certain condition.
Marks which informs people of fire under certain condition.
Marks which informs people of cracks under certain condition.
Warning
Electric shock1. Do not plug with wet hands.2. Keep power plug clean and do
not remove dust with damp cloth.
Electric shock1. Only use 3-core power outlet
with 220V and current more
than 5A.
2. Properly ground washer to
conform with all governing
codes and ordinances
Electric shock1. Do not attempt to repair or
replace any part of this
appliance except professional
maintenance staff.
2. Power cord is connectedwith Y-Shape. If it isdamaged, replace it byprofessional staff or callafter-service hotline.
3
-
8/11/2019 LG t7018aeep5
4/37
Safety information (Read carefully)
Warning
Fire or Electric Leakage1. Do not place any heat source or
open flame (such as anti-mosquito
incense, candle, cigarette, etc.)
around your washer.
Fire ,electric leakage or
short-circuit
1. Do not water on your appliance
when cleaning.
Fire or Short-circuit
1. Unplug this appliance from the
power supply after use.
2. Do not pull power cord when
unplugging.
3. Do not use when power plug
looses.
4.Do not bendbind or press the
power cord.
5. Keep your appliance free of
outdoors or wet areas.
6. Do not use your appliance on a
carpeted floor.
Explosion1. Do not add explosive substances
(such as wax, oil, paint, gasoline,etc.) to the washer. Do not
place these substances around
your washer. \
Personal Injury
1.Do not allow children to play
on ,with or inside this appliance
Personal Injury1.Never reach into washer while it
is moving
2.Wait until the machine has
completely stopped before
opening the lid and touching the
laundry
Warning
Deformation1.The temperature of washing
should be below 40 under
WARM.
2. Do not climb or hold weight on
the washer.
Damage1. Do not keep water in the washer
in case of freezing.
Vibration
1.Do not wash waterproof
clothes(such as rain cape, feathers
dressshower curtain or sleeping
bags) .
4
-
8/11/2019 LG t7018aeep5
5/37
3. Specifications
Model T70(80)18AEEP5
Power supply 220V~, 50HZ
Input power WASH POWER 430W, SPIN POWER 240W
Capacity 6.5(7.5)kg
Size (mm) 540540910 (935)
(LWH)
Water level 10 LEVEL
Water usage 148L(high water level, JET SPRAY and RINSE for 1 time)
Water tab pressure 0.3kgf/cm~8kgf/cm
Washing model Improving turbo drum washing , intelligence sense
Control model FUZZY logic control
SPIN speed 730-800RPM
Program FUZZY(NORMAL), WOOL, QUICK WASH, JEANS, TUB CLEAN, FAVORITE,
SILENT, SMART CLEANING,
Filter 2
Softener Automatic
PC board displays Yes
Accessories
Water supply hose(2) Drain hose(1) Rat-proof base(1) Bolt(1)
5
-
8/11/2019 LG t7018aeep5
6/37
3. Feature and technique instruction
3-1. DD Centrifugal Washing
WASH PROCESS
WASH PRINCIPLE
Soils
Centrifugal flow crossTub rotates
Drive tub to rotate directly through
DD motor. Stream crosses through
laundry and injects from the top of
tub.
Laun
STR
The stream takes away stains on the laundry
3-2.DD Inverter DC Motor
DD Inverter DC Motor sets magnet on rotor and winds coils on stator, whose current is
controlled by sensor and control chips instead of traditional brush.
6
-
8/11/2019 LG t7018aeep5
7/37
Structure of DD Inverter DC Motor
`
Rotor
Motor
Sensor moduleCoil
Stator
Magnet
Working Principle
Motor speed is controlled by the signal width of pulse.
Oscillogram
(Low rotate speed )
Narrow pulse width
(Low rotate speed)
Oscillogram
(High- rotate
speed )
Broad pulse width
(High- rotate speed )
7
-
8/11/2019 LG t7018aeep5
8/37
-
8/11/2019 LG t7018aeep5
9/37
3-5. Safety Reed Switch
This reed switch system may differ from the old one. The reed switch is in PC board module
and works through contacting with magnets inside lid switch. It would not work until lid is
closed and current is passed through.\
Do not place any magnetic object on the machine, which may lead to operation error.
3-6. Intelligence perception
Seven intelligence perception including unbalance, measurement, water level, door openness,
water temperature , water hardness and detergent density
Unbalance perception may differ from that of old models. It percepts unbalance through
motor rotate speed of DD motor sensor under SPIN and abnormal operation.
3-7.10 Section level
10 section water level
The water level can be adjusted manually with a cycle of
[789101234567] according to requirements as
the button is pressed.
Water
level/detergent
Water level
9
-
8/11/2019 LG t7018aeep5
10/37
-
8/11/2019 LG t7018aeep5
11/37
5-2. Connecting Water Supply Hose
Connecting Water Supply Hose to the machine
Check to see if there is a black rubber seal inside the
connector. If not, it would cause water-leakage.
Hose
Rubber seal
Inlet valve
Connect the water supply hose to inlet valve of the
washing machine vertically.
Connect the water supply hose to inlet valve of the
washing machine, and then lock it by turning the hose
connecting part.
Connecting Water Supply Hose to water tap
Separate connector from the Water Supply Hose by
pulling the Pressing Rod and the Pressing Handle that
is attached to the Water Supply Hose.
If the tap diameter is too large , remove the guide plateinside
Connector
Press
Press
Water
Untighten the 4 screws on the upper connector and
turning the down connector to leave space about 3
screws between the two connectors.
If the tap diameter is too large,
remove the guide plate inside.
Upper-con
Guide
3 screws
Down-con
11
-
8/11/2019 LG t7018aeep5
12/37
Adjust four screws on connectors to make sure that the
two screws near the wall are in tight contact with
outside of water tap.The screws close to the wall should
be screwed beforehand.
Water tap
Push the upper connector up till the rubber packing
can adhere completely to the tap (Attention: Do not
remove the rubber packing).
Turning two screws to be in tight contact with water
tap. Then tighten the 2 screws.
Turn the lower connector to be in tight contact with
the upper one (Loose connection will cause the water
leakage). Make sure the clearance between the two
connectors is less than 3mm.
Confirmation
-
8/11/2019 LG t7018aeep5
13/37
Push the pressing rod of water supply
hose when removing it.
Insert Water Supply Hose into down
connector and loosen pressing handle
during the Water Supply Hose
installation.
Make sure pressing handle is in connector slot.
Check for water leakage
After connecting the hose, open the tap to check for any water leakage.
If the connection leaks, close the tap and start again from step 1. (For example, poor installation of
upper connector or upper and down connectors is not in tight with each other.)
Loose after long-time useClose the tap and start again from step 1. (the same with moving house
or reinstalling water supply hose)
5-3. Connecting Drain Hose
Before connecting
Ensure that the hose clip is set as indicated here.
Connect the Elbow Hose
Push the elbow hose toward the body of the machine.
Place the Drain Hose
To change the direction of the hose, pull out the
elbow hose and change the direction.
Repeat Step 2.
Install or store where it will not be exposed to sunrain or windsCaution
Please use standard rated voltage.
31
-
8/11/2019 LG t7018aeep5
14/37
6.Circuit diagram
Apply in T70(80)18AEEP5
7. Washing Program
Basic process of each function (minutes)
PROCESS
WATER
LEVEL
PROGRAME
WASH RINSE SPIN
Water level8-10
level
5-7
level
3-4
level
1-2
level
8-10
level
5-7
level
3-4
level
1-2
level
8-10
level
5-7
level
3-4
level
1-2
level
FUZZY(NORMAL)
CASUAL WASH
About
20
About
17
About
14
About
10About 5 About 6
QUICK WASH About 3 About 5 About 3
SILENT About 25 About 10 About 6
WOOL About 6 About 10 About 1
JEANS
About
19
About
17
About
14
About
10About 5 About 4
TUB CLEAN About 19 About 5 About 5
Instruction:
each period time varies because of water pressure.Notes:Noise will occur under high water pressue. Use water tap switch to regulate water to eliminatenoise.
41
SMART
CLEANINGAbout 15
REACTOR220V/5A
BK/WH BLWH
DRAIN
MOTOR
DPD/P_signal
CL_SENSIN
About About About About
20 17 14 10About 6
-
8/11/2019 LG t7018aeep5
15/37
Introduction of each operation button T708018AEEP5
Notice:1. Because of automatically optimization of the micro-processor, the display time may change. The increase and
decrease of the old time should not exceed 8 minutes and 4 minutes respectively.2. The standard that compared with sensor result is set up according to the normal standard, which may not
conform to some specific users.3. The detergent amount sensor is designed according to the synthetic detergent. If you add liquid detergent,
soap powder or overdose bleach, sensor sensitivity will degrade.
51
-
8/11/2019 LG t7018aeep5
16/37
4. Sensor sensitivity will decrease after long-time use. Please use "TUB CLEAN" program to clean the inner andouter tub5. Even if the water level or temperature is changed during "STANDARD" program, the sensor is still working.Inner optimization algorithm varies because of different models6. Control panel may differ according to different models.7. "Three-level" mode is available when the water level is between 3 and 8 beside "WOOL" and "TUB CLEAN"
program.
61
-
8/11/2019 LG t7018aeep5
17/37
9.Disassembly guide
Unplug before repairing and replacing
electronic components.
Electrostatic Cautions
Chart 1
Earth wire should be connected before
troubleshooting or parts replacement.
Discharging before working if possible.
Connector
PC board module
9-1. Front panel and PC board
disassembly Remove two screw caps with sharp tools;
Then remove fixed screw on front panel
Push front panel to the left and fetch out
Remove connectors on PC board
Unload 4 screws on front panel
Unload PC board module
17
-
8/11/2019 LG t7018aeep5
18/37
Back panel
9-2. Back panel, Power
cord, Inlet valve and BP
sensor Disassembly
Then remove fixed 2 screws on
back panel.
Unload back panel
Remove a fixed screw on filter.
remove power cord after
unplugging two connectors.
BP sensor
Filter
Unplug connectors on inlet valve
and then remove fixed screws on
valve.
Sub
PCB
Fetch out inlet valve.
Unplug connector and pressure
tube from BP sensor.
Power Inlet
Fetch out BP sensor.Trsional spring
Bolt Bolt
18
-
8/11/2019 LG t7018aeep5
19/37
Tub Cycle
Fixed nutTub Cycle
Outer tub
Inner tub
CutchPivot
Connector drain hose
9-3 Back panel Disassembly
Unplug fixed screw on back panel and then
remove back panel.
9-4.Update boom components
Separate top cap from the washer.
As is shown, separate boom from outer tub.
Do not remove the boom components and
replace it whole.
Assemble according to Table below(position
and colour)
Position P/NO. PIVOT(Color )
K100 Blue
Fixed nut
RotorStator
Rotor nut
19
-
8/11/2019 LG t7018aeep5
20/37
9-5. Replace rotor and stator
remove rotor nuts with wrench(M18)
remove and fetch out rotor as is shown.
Fixed hole
Remove fixed hole and Hydraulic
conductivity board
retaining piece
Stator base
Hall element
Unplug hall element and stator connector
before removing stator.
20
-
8/11/2019 LG t7018aeep5
21/37
Circlip Untighten six stator fixed screws
Check the direction of inner calandria
circlip.
Tighten stator with handles and remove
the last screw.
Hallelement
Rtaining piece stator base
Pay attention to the wire statue in case of
noise.
9-6.Replace Clutch Components Remove 9 fixed screws on clutch and fetch
out.
21
-
8/11/2019 LG t7018aeep5
22/37
10. Test running
Applied model: T70(80)18AEEP5
Water test mode
Use test program and press DELAY,RINSEand POWER together under no load and
water level around 28L .
All the indicators are on under TEST mode. Press START/PAUSE to test following items.
Number Test method LED display Test items
1 Initial status
Alternation display of Version U: 00
and water level frequency
Water level sensor abnormal
displayPE
All the indicators are
on
Water level frequency
is 218-250
2 Press one timeAlternation display of Version d:00,
S:00 and 15d7(8)Test Alpha stream
3 Press twice Display 2 Alpha stream stops
4 Press three times Display hardness valueHardness value is
0-255
5 Press four times Display 4 Drain
6 Press five times Automatic switch is off All indicators are off
Anhydrous test mode
Use test program and press WASH,RINSEand POWER together under no load and no
water.
Test following items under TEST mode.
Number Test method LED display Test items
1 Initial status Display TS
2Press WASH and then press
START/PAUSEDisplay 20
Check if it is under normal
WASH condition
3 Press POWER/AUTO OFF Automatic switch is off All the indicators are off
4 Press combination button again Display TS
Press SPIN and then press
START/PAUSE5 Display 9
Check if it is under normal
SPIN condition.
22
-
8/11/2019 LG t7018aeep5
23/37
11. Troubleshooting
11-1.Check the problem against the list bellows
Symptom Error
Message
Check up Check up
Water supply failure Is the water tap shut off?
Is the water supply cut off
Is the water tap, water hose or inlet valve
clogged?
Is the connector connected?
Drainage Failure Is the drain hose positioned correctly?
Is the drain hose bent or placed too high?
Is the internal part of the hose clogged?
Spin failure Is the laundry evenly balanced?
Is the washing machine placed on a flat
surface?
Is too much detergent used?
Door(Lid ) open Is the lid closed?
Internal sensing
failure
Overflow failure
Motor failure
see detailed information later
Clutch failure
23
-
8/11/2019 LG t7018aeep5
24/37
11-2. Display troubleshooting according to errors
Problems Reasons Possible causes Solution measures
Water
supply
Sensor null water level is under
26.0khz when watering for 12
minutes.
Sensor the water level remains
unchanged every 5 minutes with
water supply above null water level.
water tap is shut off
water supply is cut off
Inlet valve is clogged
Connector is installed
improperly.
Connection error of inlet
valve six-leg connector
and sub PC board.
Turn on water tap
Wait for water supply
Clean or replace filter
Connect connectors
properly
As above
drainage Water does not drain within 12
minutes.
Sensor water level is under 25.7khz for
6 times during SPIN with water.
Is the drain hose
positioned correctly?
Is the drain hose
clogged with impurities.
Is the internal part of
the hose clogged
Height of drain hose
should be less than 6 cm
from the floor.
Remove any foreign
objects inside pump.
Replace the drain motor
or connect connectors
properly.
Unbalance Three open circuits occur during
SPIN due to clothing placed
unevenly.
laundry in the tub is
placed unevenly.
The washer is placed on
an un-flat surface.
Place the laundry
evenly
Adjust Adjustable Legs
Door(Lid)
Open
Lid is open during SPIN and WASH
Continuous Alarm
Lid is open during SPIN
Process.
Lid is open during
WASH PROCESS
Connection error of PC
board connectors.
Close lid
Close lid
Connect connectors
properly.
Check over
24
-
8/11/2019 LG t7018aeep5
25/37
Problems Reasons Possible causes Solution measures
Internal
sensing
failure
Water level switch is
close
Connection error of water level
switch or eight-leg PC board
connector
Air chamber or hose is clogged.
Water level switch is damaged
Connect connectors properly
Fix air chamber and remove
foreign objects.
Replace water level switch
Overflow
failure
Check if the leakage or drain
hose height extends 6cm
from the ground.
Check if outer tub pore or air
tube is clogged.
Check if there is leakage in
poresair tubes or connectors
Place drain hose 6cm
underneath.
Replace water level switch
Motor
failure
Connection error of Hall
element or eight-leg PC board
connector
Connection error of Motor
stator or Yellow 3-leg PC board
connector
Hall element is damaged
Stuck by clutch
Connect connectors properly
replace stator
replace clutch
replace PC board
Clutch
failure
Drain motor connector looses Connect connectors properly
Connector output voltage is
abnormal.
Replace PC board
25
-
8/11/2019 LG t7018aeep5
26/37
12. Maintenance Guide
12-1.Common washing problems
Many washing problems involve poor soil&stain removal, residues of lint and scum, and fabric
damage. For satisfactory washing results, follow these instructions.
WASH PROBLEM
Problems Possible causes Solution& Preventive Measures
Poor soil removal Not enough detergent
Wash water temperature
too low
Overloading the washer
Incorrect wash cycle
Incorrect sorting
Do not pretreat stain
Use correct amount of Detergent for load size, amount
of soil and water Hardness.
Use WARM or HOT water for normal soil. Different
Water Temperature may be required according to Soil
type.
Reduce load size
Wash with POWER cycle for heavy soiled laundry
Separate heavily soiled items from lightly soiled ones.
Blue, Gray or Brownstains
Undiluted fabric softenerdispensed directly onto
fabric
Rub the stain with bar soap. Wash.Do not overfill fabric softener dispenser and do not pour
liquid fabric directly onto fabric.
Black or gray marks
on clothes
A buildup caused by the
interaction of fabric
softener and Detergent
can flake off and mark
clothes.
Not enough detergent
Use correct amount of detergent for load size, amount of
soil and water hardness.
Yellow or brown rust
stains
Iron or manganese in
water supply, water pipes
Not enough detergent
To restore discolored load of whites, use rust remover
safe for fabric
Install nonprecipitating water softener or an iron filter in
your water supply system for an ongoing problem Before washing, run water for a few minutes to clear
lines.
Lint Incorrect sorting
Tissues left in pocket
overloading the washer
Wash lint givers eg towels, flannelette sheets, separately
from lint collectors eg synthetic fabrics
Remove tissues in pockets before wash. See attentions
for sorting and caring before loading.
Do not overload the washer
Residue or detergent Overloading the washer
Undissolved detergent
Use too much Detergent
Do not overload the washer
Some Detergents need to be pre-dissolved, check the
Detergent instructions. Try pre-dissolving the
Detergent in warm water.
Increase Water Temperature using HOT water safe for
fabric.
Use proper amount of Detergent.
Holes, tears, or snags Incorrect use of chlorine
bleach
Unfastened zippers,
hooks, buckles
Ribs, tears and broken
threads
Never pour chlorine bleach directly on fabric
Fasten zippers, hooks, and buckles
Overloading the washer
Degradation of fabric
Remove objects in pockets
Do not overload the washer.
26
-
8/11/2019 LG t7018aeep5
27/37
12-2. How to diagnose and maintain according to symptoms
1) Power Failure
Where, what and how Check results
Possible
reasons
Solution measures
Power
Yes Electric
problems
1. Check if the socket is in poor
contact.
Replace plugs
Normal None2. measure voltage
0V Power
supply
Contact Power Supply Bureau
-
8/11/2019 LG t7018aeep5
28/37
2) Display problem
Where, what and how Check results Possible reasons Solution measures
Main voltage
1. measure main voltage Less than 85% of normal
voltage
Low voltage
Because of low voltage
supply. Please use
transformer if voltage is
keeping low.
2. measure external insert
row voltage if main
voltage is normal.
Less than 85% of normal
voltage
Wire is too small or there
are too many
connections on insert
row.
Use transformer
PC board
1. LED damage
2. LED drive circuit
damage
3. Chips damage
PC board damage
Replace PC board
3) Restart during working
Where, what and how Check results Possible reasons Solution measures
Main voltage
1. measure plug voltage
during working
Less than 80% of normal
voltage
Main voltage is too low or
wire size is too small.
Because of low voltage
supply and please use
suitable wire.
2. restart fault repeats
during special periods
Temporary voltage surge Because of environmental
condition(high-frequenc
y voltage around)
3. check if there is voltage
change.(such as flashing
lights)
Because of power supply
environment
PC board Replace PC board
1. It must be PC board
fault if there is no
main voltage fault.
28
-
8/11/2019 LG t7018aeep5
29/37
4) No water supply
Check Check results Possible reasons Solution measures
Inlet valve
1 Water is not flowing
into inner tub and
there is current flow
though inlet valve is
working.
1) Check if water tap is
close.
Close Close Explanation
2) check if the tap is
open
No Use error Open water tab
3)remove inlet valve and check
filter if problems are not
mentioned above.
Filter is clogged No cleaning Use a brush to clean the
filter and filter should be
cleaned regularly.
3) check whether
membrane hole is
clogged with foreign
objects or piston
inside valve is locked
if problems are not
mentioned above.
Inlet valve fault Replace inlet valve
2 If inlet valve is not
working and there is
no current sound
during water supply.
1) Check if connectors
are not connected or
connected unproperly.
Poor connection Connection fault Connect again or
implement
troubleshooting caused by
poor connection.
2) Check inlet valve
resistance
Not between 0
812K
Coil is cut off Replace inlet valve
Pressure sensor
1 If error message PE is
displayed: sensor fault.
PEerror display Connectors do not
connect or harness, coil is
cut off.
Connect connectors or
replace harness. If coil is
cut off, replace the sensor.2Check BP sensor (pressure
sensor) frequency with no
load and no water supply.
Less than 20KHz BP sensor fault Replace BP sensor fault
Yes Replace PC boardPC board
1If inlet valve and sensor have
no fault, check the PC
board.
29
-
8/11/2019 LG t7018aeep5
30/37
5)Continuous or intermittent water supply
Check Check results Possible reasons Solution measures
Incorrect installation/water
leakage
1Check if drain hose is
placed on the floor.(Pump
model)
Yes Incorrect installation Drain hose should be
hang over standpipe or
wash tub. Replace parts.
2Check leakage place Water leakage from
some parts
Parts fault Repair the parts
Pressure sensor
1 Check if wave wheel
rotates with no water supply.
No No water pressure sensor Check if pressure sensor
pipe is broken and repair
it.
2 Check if air hole is
clogged there is no sensor
fault.
Yes Air hole is clogged Repair air hole
Inlet valve
1 Is there water supply
under no power(power
is off)?
Yes Inlet valve fault Replace inlet valve
PC board
1Press POWER and there
is water supply
immediately before
START/PAUSE
pressed.
Short-circuit of controlled
silicon
Replace PC board
30
-
8/11/2019 LG t7018aeep5
31/37
6) Display LE and out of work
Check Check results Possible reasons Solution measures
1Check connectors Poor connection Connection fault Connect again or
implement
troubleshooting caused by
poor connection.
2Check rotor magnet Cracked Replace rotor
3Measure if resistance
between two legs of stator
connector is between
515.
Yes
No
None
Stator fault Replace stator
Normal
Abnormal
None
Hall element fault
4Check Hall element
Replace Hall element
5It must be PC board
fault if fault is not
mentioned above.
Replace PC board
7) Power failure
Check Check results Possible reasons Solution measures
Main voltage
Input voltage is abnormal
caused by interference.
Input voltage fault Explanation
( high-frequency device
around washer)
Automatic power relay orPC board
1 Check if power is
off automatically when
unplugging power cord
during power is on.
2 There must be PC
board fault if power is off
immediately when power
is on and power switch is
under good condition.
Power is cut off
immediately.
Power switch fault Replace PC board
31
-
8/11/2019 LG t7018aeep5
32/37
8) Undrained
Check Check results Possible reasons Solution measures
Drain motor
Yes Clogged with foreign
objects
1 Check if there is
working sound of drain
motor.
Unplug drain valve and
remove foreign objects
2Measure resistance if
there is no working
sound
Drain motor coil is cut off Replace drain motor
Connector fault Connector fault Repair connector3Check connectors if
there is no working sound
and resistance is normal.No Connector fault PC board fault Replace PC board
Drain hose
Winded Installation problem Install it again to avoid
winding
1Check if the space is
too small to place
drain hose or hose is
winded
2Check if drain hose is
folded or clogged
with foreign objects.
Clogged Drain hose is clogged Remove foreign objects or
install it again to avoid
winding.
9) Drain out of drainage time
Check Check results Possible reasons Solution measures
Clogged with foreign
objects
Remove foreign objects
Drain valve shell
1Check whether rubber
bellows are deformed
or there are foreign
objects in drain valve
components if keeping
draining.
Deformation of rubber
bellows
Deformation of rubber
bellows
Replace rubber bellows
PC board
1Check if drain motor or
drain pump runs
immediately when
power is on.
Yes
PC board fault
Replace PC board
Drain hose
1Check if drain hose is
properly installed. The
discharge height should
be approximately0.9-1.2m from the floor.
less than suggested height
Incorrect installation
Place the outlet of drain
hose 0.9-1.2m from the
floor.
32
-
8/11/2019 LG t7018aeep5
33/37
10) Drainage fault during drainage time
Check Check results Possible reasons Solution measures
-
8/11/2019 LG t7018aeep5
34/37
13.Disassembly diagrams and Parts list
43
-
8/11/2019 LG t7018aeep5
35/37
13-1.The Exploded View Of Top Cover Assembly
A062A060
A210
A160
A100
A170
A010
A027
A172
A180
A240
A200
A190
A150A152
A230
A173
A160
A171
A063
A052
A020
A065
A040
A061
A030
35
A181
HOT(ORANGE)
COLD(BLUE)A270
A064
-
8/11/2019 LG t7018aeep5
36/37
13-2.The Exploded View Of Cabinet Assembly
F070
F020
F000
F001
F023
F023
F024
F090
36
F002
F003
F004
F005
F090
F040
-
8/11/2019 LG t7018aeep5
37/37
13-3.The Exploded View Of Tub Assembly
K064
K000
K021
K020
K250
K061
K110
NATURAL
K200
K210
K201
K305
K300
K340
K290
K240
K050
K063
K062
K060
K040
K012
K090
K140
K370
K005
K011
K100
K105
K004
K230
K270