20091218112714 j Yee 1 z

8/13/2019 20091218112714 j Yee 1 z

1/40

EXCELL PRECISION CO., LTD.

FB530/FB630

(Conversion)Dot MatrixPrinter Indicator

User Manual

EXCELL PRECISION CO., LTD. 2009. All rights reserved worldwide.

The information contained herein is the property of EXCELL PRECISION CO., LTD. and is

supplied without liability for errors or omissions. No part may be reproduced or used except as

authorized by contract or other written permission. The copyright and the foregoing restriction on

reproduction and use extend to all media in which the information may be embodied.

8/13/2019 20091218112714 j Yee 1 z

2/40

8/13/2019 20091218112714 j Yee 1 z

3/40

FB530/FB630 ZSME3000001591


Table of ContentsInstructions for Use .................................................................................................................... 2

Preparing to Use the Indicator ................................................................................................... 2

Chapter 1 General Introduction ................................................................................................. 3

1-1 Display Description ........................................................................................................... 3

1-2 Power Descr iption ............................................................................................................. 4

1-3 Keypad Description ........................................................................................................... 5

Chapter 2 General Operation Description................................................................................. 6

2-1 Backlight Function ............................................................................................................ 6

2-2 Weighing Mode.................................................................................................................. 6

(1). Units Select ion............................................................................................................... 6

(2). Check Weighing Mode .................................................................................................. 6(3). Totalizing........................................................................................................................ 8

(4). Zero Funct ion................................................................................................................. 8

(5). Tare Function ................................................................................................................. 9

(6). Printing Funct ion (only for FB model) ....................................................................... 10

2-3 Counting Funct ion .......................................................................................................... 12

(1). Sampl ing ...................................................................................................................... 12

(2). Check Weighing........................................................................................................... 12

(3). Totalizing...................................................................................................................... 12

Chapter 3 General Funct ion Setting ........................................................................................ 13

Check weighing configuration ............................................................................................. 14

RS-232 Interface (opt ion) and Mini Printer Output Setting ................................................ 15

Exit Setting Mode .................................................................................................................. 25

Weight Hold Mode setting .................................................................................................... 26

G value Calibration ................................................................................................................ 28

Load Cell Pin Description (input signal) ................................................................................. 29Option Function Description.................................................................................................... 30

Error Messages ......................................................................................................................... 30

Appendix 1 ASCII Code Table ............................................................................................... 31

Appendix 2 7-Segment Display Characters ......................................................................... 32

Appendix 3 Printer Installat ion.............................................................................................. 33

Appendix 4 Load Hook Installation ....................................................................................... 34

8/13/2019 20091218112714 j Yee 1 z

4/40

FB530/FB630 ZSME3000001592


Instructions for Use1. The indicator should not be drenched by rain or water. (If it gets wet carelessly, please

wipe it dry with a cloth. If its operation is abnormal, please send it to our distributor for

service.

2. Please keep the indicator in a cool and dry place. Do not store at high temperatures or

humid places.

3. Please keep the indicator clean and free from insect infestation.

4. To avoid impact and it is to be used under designated pressure (the weight put on the

platter can not exceed the maximum capacity of the indicator)

5. If the indicator is not going to be used for some time, please clean it and store it in a

plastic bag in dry condition. A desiccant sachet may be included to prevent moisture from

building up. The internal rechargeable battery should be recharged every three months.

6. Any suggestion for the product is warmly welcome.

Preparing to Use the Indicator1. Put the indicator on a firm and flat surface for accurate weighing reading. Adjust the four

leveling feet to get the leveling bubble at the center of the circle.

2. The indicator must be used under a stable temperature and stable air flow. Avoid direct

sunlight onto the indicator or near the air-conditioning outlet.

3. Indicator must be used under individual socket to avoid the interference of other electric

appliances.

4. Remove any weight that might be on the platter before the indicator is switched on.

5. The indicator requires 15 ~ 20 minutes warm up before operation to ensure best

accuracy.

6. Please note that when symbol appears on the screen, the indicator needs to be

recharged.

Thank you for purchasing EXCELL (Conversion)

Dot Matrix Printer Indicator. To guide you to use

our product correctly, please read the user manual

carefully to avoid mis-operating this product.

8/13/2019 20091218112714 j Yee 1 z

5/40

FB530/FB630 ZSME3000001593


Chapter 1 General Introduction

1-1 Display Description

Changes of Range indication mode

The indicator with 2-segment specification:

6 is Range 1 5 is Range 2

: High limit value

: OK value (The value between HI and LO limit value)

: Low limit value

: kg or g unit

: Pound unit

: Taiwan and Hong Kong units: Counting mode indication

: Percentage: Zero indication

: Net weight indication

: Low battery power indication

1 : Stable indication

2 : Pretare mode indication

3 : Accumulation mode indication

4 : Printer ready indication (Mini Printer connection)

5: Samples insufficient indication

6 : Unit weight insufficient indication

7 : Viss unit (Burma unit)

1 2 3 4 75 6

8/13/2019 20091218112714 j Yee 1 z

6/40

FB530/FB630 ZSME3000001594


1-2 Power Description

Power Selection

1. 6 V / 4 Ah Rechargeable battery

2. 110 / 220 V 15%AC Main power

Recharge Voltage

1. AC 110 V +10% , -15%

2. AC 220 V +10% , -15%

Power Consumpt ion

State Power ConsumptionContinue Operation

Timedo not print(indicator + Load Cell + 2 sides

backlight + Mini Printer)Less than 55 mA Over 70 hoursWith a load cell

(350 )

printing(indicator + Load Cell + 2 sides

backlight + Mini Printer)Less than 350 mA Over 10 hours

(indicator + Load Cell) 26 mA About 180 hours

(indicator + Load Cell + frontdisplay backlight)

32 mA About 140 hoursWithout aprinter

(indicator + Load Cell +reardisplay backlight) 40 mA About 110 hours

Only RS-232Card

About 20 mA

Low Power Alarm

Please note when the ( ) symbol keeps flashing on the left down corner of the display, the

batteries should be charged.

The indicator will turn off automatically after 5 ~10 hours (approximately 1~2 hours with

backlight on), when the low battery warning symbol shows up. The indicator must be fully

charged, before operating again.

When the low battery warning symbol shows up, please charge the indicator immediately for

fear of weight instability.

The indicator becomes unstable because of the large power consumption. Not be allowed

taking off the battery when equipped with mini printer.

EEPROM Power (for model with mini printer)

When using the rechargeable battery but AC power and the voltage is below 3 V, the data of

date, time, etc in RTC IC will disappear in 24 hours.

8/13/2019 20091218112714 j Yee 1 z

7/40

FB530/FB630 ZSME3000001595


1-3 Keypad Description

: Press this key to select the required unit from the preset units.

: Press this key to preset the HI, OK, LO value.

: Press this key to accumulate the weight value or others.

: Press this key to deduct the container weight.

: Press this key to preset tare value.

:Press this key to recall the accumulation value, preset value and pretare value.

:Press this key to clear the accumulation value, preset value and pretare value.

: Press this key to zero the indicator.

: Press this key to confirm.

: Press this key to light up the backlight.

: Press this key to enter into counting mode.

: Press this key to sample.

: Press this key to print the total data.

: Press this key to input the numbers (0 ~ 9).

: Press this key to advance the paper.

8/13/2019 20091218112714 j Yee 1 z

8/40

FB530/FB630 ZSME3000001596


Chapter 2 General Operation Description2-1 Backlight Function

Press key to choose the display backlight mode:

. Auto Backlight mode. When the weight is over 10d or any key is

pressed, the display backlight will be switched on. When the weight

returns to zero (the weight on platform is less than 10d), the display

backlight will switch off after 10 seconds.

. Display backlight is on all the time.

. Display backlight is off.2-2 Weighing Mode

(1). Units Selection

The selected unit will be memorized when you turn the indicator off. And the memorized unitwill appear after you turn on the indicator next time.

(2). Check Weighing Mode

1. Preset High limit, Low limit and Beeper value operation

Use and key to preset values.

For example:

Preset Low limit ( Low limit >10d ) e.g. Low limi t = 20 kg

Press key the display shows .

Press key 1 time the display shows .Press key 2 times the display shows .

Press key 4 times the display shows .

Preset High limit ( High limit Low limit ) e.g. High limit = 25 kg

Press key 1 time the display shows .






Preset Beeper value ( Refer to Note) e.g. Beeper value = 22

Press key 1 time the display shows

Press key 2 times the display shows

Press key 1 time the display shows

Press key 2 times the display shows


8/13/2019 20091218112714 j Yee 1 z

9/40

FB530/FB630 ZSME3000001597


Preset Single point (preset low limit only):

After preset low limit procedures is completed and the display shows . ,

then press key again, the display shows . . This means that the preset single

point procedure is completed.

NOTE

_ _ _ x xA B

A Setting for the status that LCD is on and the beeper beep:

0 = when stable, the beeper beeps and LCD is on.

1 = when stable, the beeper beeps; whether stable or not, LCD is on.

2 = whether stable or not, the beeper beeps and LCD is on.

B Setting for the beep status:

0 = No beep1 = OK (when the weight is over Low Limit & under or equal to High Limit.), the

beeper beeps.

2 = When the weight is under or equal to Low Limit & over High Limit, the beeper

beeps.

Under Status in Preset Low Limit (preset single point only)The BEEP, LCD mode should be fixed as follows:

When over Low Limit, the beeper beeps and is offWhether stable or not, the beeper beeps and LCD indication is on

LCD indication:

10d Low Limit High Limit

To exit preset mode, please press key.

2. Recall Check-weighing ValuesPress key then press key Recall Low limit value

Then press key again Recall High limit value

Then press key again Recall Beeper value

Then press key again Back to the beginning

3. Clearing Check-weighing Values

Press key then press key, and then press key Recall Low limit value

Then press key again Clear High limit value and Beeper value

Press key then press key 6 times continuously Clear all values

8/13/2019 20091218112714 j Yee 1 z

10/40

FB530/FB630 ZSME3000001598


(3). Totalizing

1. Weight Totalizing

Place goods on the platter, after stable and press key to save the weight value.

Then the display shows the total number of additions and the totalized weight value.

And the (M+) indication

will flash on the display. The indicator will recover to show theweight value of the goods on the platter after 3 seconds and the (M+) indication is on.

The indicator allows the next totalizing operation, even when the weight value does not

return back to zero. The key is functional, when the weight value changes by more

than 10d. The indicator will save the totalized weight value after the weight is stable.

The indicator can totalize positive or negative weight but cant do both at the same time.

The totalized weight store must be reset to zero before it is possible to select positive or

negative totalizing mode.

The totalizing function can be used up to a maximum of 9999 times before it must be reset.

The totalizing display is limited to 6 digits maximum.

When totalizing, RS-232 and Mini Printer will also output. ( Refer to F5 setting)

2. Clear Totalized Weight Values

Press then key to clear all totalized weight values.

When changing between weighing and counting mode, or selecting weighing unit, the

indicator will automatically clear all the totalized weight values.The indicators will automatically clear all the totalized weight values after turning on.

3. Recall Totalized Weight Values

Press key to display the total number of additions and the totalized weight value.

And the (M+) indication will flash on the display. The indicator will return to the weighing

mode after 3 seconds.

The indicator will not display the negative sign - for negative totalized weight values whenrecalling a totalized weight value, but when printing, the negative sign - will be printed out

(transmitted serially) for each negative weight and negative totalized weight.

(4). Zero Function

Press key to re-zero the display with no load on the platter. When zero is set, the

( ) symbol will be displayed.

8/13/2019 20091218112714 j Yee 1 z

11/40

FB530/FB630 ZSME3000001599


(5). Tare Function

1. When the weight of the container is unknown ( )

Place the container on the platter, after stable and press key, the weight value

returns to zero and net indication ( ) is on.

Place goods into the container, then the indicator shows the net weight of goods.

Clear tare value

When removing the container and goods, the display shows the negative weight value of

the container. Then press key to clear tare value. The indicator returns to zero and

net indication ( ) is on.

Recall tare value

Press then keythe display shows tare value

Multiple tare operation Users can continuously increase or decrease the tare value by

pressing the key.

The total tare value (tare value + pre-set tare value) can equal the full capacity of the indicator.

2. When the weight of the container is known ( )

Press key and the display shows . .

Use and keys to input weight value of the container. After finishing the

procedures, the net indication ( ) and pretare indication is on.

Place goods into the container, then the indicator shows the net weight of goods.

Clear pretare value

Press then key, and then press key to clear pretare value.

When the indicator returns to zero, net indication ( ) and pretare indication are

off.

Recall pretare valuePress then keythe display shows pretare value

In Tare mode, the Preset tare function is disabled.

The indicators with two weighing ranges can NOT pre-set the tare value larger than the first

weighing range. For example: a 30 kg indicator is set by two weighing ranges. The first range

is 0 to 15 kg, and the second range is 15 to 30 kg. The pre-set tare value can not be larger

than 15 kg.

8/13/2019 20091218112714 j Yee 1 z

12/40

FB530/FB630 ZSME30000015910


(6). Printing Function (only for FB model)

F5 Function Press key Press keyPress key twice

after zeroing

RS-232 closed

r n p 0 Printer closed

RS-232 and

Printer do nottransmit

RS-232 and

Printer do nottransmit

RS-232 and Printerdo not transmit.

Totalized values donot clear off

When weight is stable,RS-232 transmits

automatically(when re-zeroed,

RS-232 transmits nexttime after stable.)

r n p 1

Printer closed

RS-232 andPrinter do not

transmit

RS-232 andPrinter do not

transmit

RS-232 and Printerdo not transmit.

Totalized values donot clear off

RS-232

continuously transmitsr n p 2

Printer closed

RS-232

transmitsPrinter does not

transmit

RS-232

transmitsPrinter does not

transmit

RS-232 transmits

Printer does nottransmitTotalized values do

not clear off

RS-232totalizes and transmits

RS-232transmits whenweight changes

by over 10d


by over 10d

RS-232 prints TOTALand clears totalized

valuesr n p 3

Printertotalizes and transmits

Printertransmits whenweight changes

by over 10d


by over 10d

Printer prints TOTALand clears totalized

values

RS-232totalizes and transmits


by over 10d


by over 10d


valuesr n p 4

Printertotalizes and transmits


by over 10d


by over 10d


values

When weight is stable,

RS-232 totalizes andtransmits automatically(when re-zeroed,

RS-232 transmits nexttime after stable and.weight changes by

over +10d)

RS-232 doesnot transmit



values

r n p 5When weight is stable,

Printer totalizes andtransmits automatically

(when re-zeroed,

Printer transmits nexttime after stable and.weight changes by

over +10d)

Printer does not

transmit

Printer does not

transmit

Printer prints TOTAL

and clears totalizedvalues

8/13/2019 20091218112714 j Yee 1 z

13/40

FB530/FB630 ZSME30000015911


RS-232totalizes and

transmits


by over 10d


by over 10d


valuesr n p 6

Printertotalizes and

transmits


by over 10d


by over 10d


values

RS-232totalizes and

transmits


by over 10d


by over 10d


valuesr n p 7

Printertotalizes and

transmits


by over 10d


by over 10d


values

After RS-232 is

stable , presskey to transmit



by over 10dr n p 8

Printer closedPrinter does not

transmitPrinter does not

transmit

RS-232 and Printer donot transmit.

Totalized values do notclear off

Note: press and keys respectively to print labels of different forms.

8/13/2019 20091218112714 j Yee 1 z

14/40

FB530/FB630 ZSME30000015912


Pcs

.

. .

. . .

. . . .

2-3 Counting Function(1). Sampling

Press key to select sample quantity from 10,20,50,100 and the display shows

, , , accordingly.

Select sample quantity and then place samples on the platter, and then press key,

the display shows .

After stable, the indicator enters into counting mode and the display shows sample

quantity.

Insufficient Sample ( ) Sample weight is less than 20 divisions.

Insufficient Unit Weight ( ) Unit weight is less than 0.2 division.

When sampling, the above two symbols indications are on. Under such conditions, the

indicator can still work, but may result in lower count accuracy.

When using 2-segment weighing mode, the above two symbol indications change to

Range 2 and Range 1 and the two symbol indications are off.

(2). Check WeighingRefer to the operation of check weighing in weighing function on page 7 ~ 8.

(3). TotalizingRefer to the operation of totalizing in weighing function on page 9.

8/13/2019 20091218112714 j Yee 1 z

15/40

FB530/FB630 ZSME30000015913


Chapter 3 General Function Setting Switch on the indicator. While the indicator is counting down to zero, press and hold key

until the display shows the software program version number.

Release the key, the indicator enters into the configuration setting mode and is

showed on the display.

Internal calibration (Reserved)




Check weighing configuration

RS-232 interface (option) or MiniPrinter output setting

Exit setting mode


Weight hold mode setting


G value Calibration

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press key

Press keyPress key

8/13/2019 20091218112714 j Yee 1 z

16/40

FB530/FB630 ZSME30000015914


Press key

Press key

Press key

Check weighing configuration

F8 (Hold) affects accessing to F4. If F8 is set, accessing to F4 is denied.

Press or key to select F4 functionthe display shows

Preset LO value

(LO value >10d)

Press andkey to set LO value

E.g. LO value = 2 kg

Preset HI value

(HI value LO value)

Press and

key to set HI valueE.g. LO value = 2.5 kg

Preset Beeper value

Press and

key to set HI valueE.g. Beeper value = 22

. kg

. kg

Press key for 5 timesto clear HI, OK, LO values

Press key

. kg

key = Increase the flash value by one (from 0 to 9)

key = Confirmation key .

kg

A BA 0 = After stable, the beeper beeps and the

indications are on1 = After stable, the beeper beeps; whether

stable or not, the indications are on.2 = whether stable or not, the beeper beeps

and the indications are on.B 0 = No beep

1 = OK (when the weight is between Low limit& High limit.), the beeper beeps.

2 = When the weight is under or equal to Lowlimit (must be over 10d) & over or equalto High limit, the beeper beeps.

LCD indication description:

10d Low limit value High limit value

. kg

kg

kg

Press key

8/13/2019 20091218112714 j Yee 1 z

17/40

FB530/FB630 ZSME30000015915


RS-232 Interface (option) and Mini Printer Output Setting J1 and J3 on the RS-232 interface are short, when the RS-232 interface is connected to a

computer.

Mini Printer interface is set as 9 600, N 8 1, including the date and time setting.

You are welcome to check with your local supplier to get a soft copy of EXCELL's

Printing Title Editing Program (a Windows-based application software)


Press keyThe display shows the defaultValue of transmission mode

Press keySelect transmission mode

Press keyThe display shows the defaultvalue of RS-232 baud rate

Press keySelect RS-232 baud rate(1 200, 2 400,4 800,9 600)

Press key

Next Page

key = Increase the flash value by one (from 0 to9) or selecting baud rate from 1 200,2 400,4 800,9 600

key =Confirmation key

No transmission (none)Stable transmission (RS-232)Continuous transmission (RS-232)Press key to transmit (simple mode)(RS-232, Mini Printer)Press key to transmit (Complete

mode) (RS-232, Mini Printer)

Stable transmission (totalizing mode).The format is as same as(RS-232, Mini Printer)

Date and time printing modeThe format is as same as

(RS-232, Mini Printer)

Date and time printing modeThe format is as same as(RS-232, Mini Printer)

After stable, press key to transmitThe format is as same as

and . (RS-232)

(from 0 ~ 8 )

8/13/2019 20091218112714 j Yee 1 z

18/40

FB530/FB630 ZSME30000015916


Press key

Press key

Connect Mini Printer before cont inue

Last Page

Press keyto select printing language

Press key

Refer to Pages 18~ 23 for details of DATA FORMAT

Mini Printer Printing Language

Reserved

English

Traditional Chinese

Reserved

Default setting: Reserved

Date Printing Order Setting

YY MM DD

MM DD YY

DD MM YY

Default setting: YY MM DD

Press keyto select printingdate order

Press key

Press key

Press key

Input YY MM DD

Input HH MM DD

8/13/2019 20091218112714 j Yee 1 z

19/40

FB530/FB630 ZSME30000015917


RS-232 Interface FormatI . Mode :UART Signal of EIA-RS0232 C

II. Format :1. Baud rate : 1 200, 2 400, 4 800, 9 600

2. Data bits : 8 bits3. Parity bit : None4. Stop bits : 1 bit5. Code : ASCII (Exchange code of American standard)

Start bit Data bits Stop bit

RS-232 Data Format

Stable transmission ( ),Continuous transmission ( ),

Press key to transmit ( )(1) Weight unit is g

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 g

HEAD , HEAD , DATA UNIT CR LF

(2) Weight unit is kg or lb

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 kg/lb


(3) Weight unit is viss

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 viss


HEAD1 ( 2 BYTES ) HEAD2 ( 2 BYTES )

OL - Overload , Under loadST - Display is Stable NT - NET Mode

US - Display is Unstable GS - GROSS Mode

DATA ( 7 or 8 BYTE )

2D ( HEX ) = ( MINUS )2B ( HEX ) = + 2E ( HEX ) = . ( DECIMAL POINT )

UNIT ( 2 or 4 BYTE )

kg = 6B ( HEX ) ; 67 ( HEX )lb = 6C ( HEX ) ; 62 ( HEX )viss = 76 ( HEX ) ; 69 ( HEX ) ; 73 ( HEX ) ; 73 ( HEX )

8/13/2019 20091218112714 j Yee 1 z

20/40

FB530/FB630 ZSME30000015918


Transmission example:

Data format for RS-232 continuous transmission are as below:

1. The gross weight (+0.876 kg) shows as below, after stable: (no tare or under pretare mode)

S T , G S , + 0 0 0 . 8 7 6 k g 0D 0A

HEAD , HEAD , DATA UNIT C LF

2. The net weight (-1.568 lb) shows as below without weight stability: (no tare or under pretare mode)

U S , N T , - 0 0 1 . 5 6 8 l b 0D 0A


3. The net weight (+1.245 viss) shows as below, after stable: (no tare or under pretare mode)

S T , N T , + 0 0 1 . 2 4 5 v i s s 0D 0A


Press key to transmit (simple mode)

English

S/N WT/UNIT ( kg / lb )

- - - - - - - - - - - - - -

0001 1.0000 Press or key





- - - - - - - - - - - - - -

0005 5.0000 Press twice to print TOTAL

Besides English, the model is able to choose Traditional Chinese as printing

form.

8/13/2019 20091218112714 j Yee 1 z

21/40

FB530/FB630 ZSME30000015919


Stable Transmission (totalizing mode)

English

S/N WT/UNIT ( kg / lb )

- - - - - - - - - - - - - -

0001 1.0000 The indicator is stable





- - - - - - - - - - - - - -



form.

8/13/2019 20091218112714 j Yee 1 z

22/40

FB530/FB630 ZSME30000015920


Press key to transmit (complete mode)

English

4-key serial 15 or 12-key serial

Press or key Press or key

Press or key

Press or key

Press or key

Press or key

Press twice to print

TOTAL

Press twice to printTOTAL

G = GROSS T = TARE PT = PRE-TARE N = NET


form.

TICKET NO .0001

G 1.000kg

T 0.000kg

PT 0.000kg

N 1.000kg

(3 blank lines)

TICKET NO .0002

G 1.000kg

T 0.000kg

PT 0.000kg

N 1.000kg

(3 blank lines)

TICKET NO .0003

G 1.000kg

T 0.000kg

PT 0.000kg

N 1.000kg

(3 blank lines)

TOTAL NUMBER

OF TICKETS 0003

TOTAL

NET 3.000kg

(3 blank lines)

TICKET NO .0001

G 1.000kg

T 0.000kg

N 1.000kg

(3 blank lines)

TICKET NO .0002

G 1.000kg

T 0.000kg

N 1.000kg

(3 blank lines)

TICKET NO .0003

G 1.000kg

T 0.000kg

N 1.000kg

(3 blank lines)

TOTAL NUMBER

OF TICKETS 0003

TOTALNET 3.000kg

(3 blank lines)

8/13/2019 20091218112714 j Yee 1 z

23/40

FB530/FB630 ZSME30000015921


RTC setting , the form is the same with

Press key to transmit (simple mode) (The date and time will not betransmit without mini printer.)

English

DATE:2008/02/25TIME : 14:30:21S/N WT/UNIT ( kg / lb )

- - - - - - - - - - - - - -






- - - - - - - - - - - - - -



form.

8/13/2019 20091218112714 j Yee 1 z

24/40

FB530/FB630 ZSME30000015922


DATE: 2008 / 02 / 25

TIME: 14 : 30 : 00

TICKET NO .0001

G 1.000kg

T 0.000kg

PT 0.000kg

N 1.000kg

(3 blank lines)

DATE: 2008 / 02 / 25

TIME: 14 : 30 : 00

TICKET NO .0002

G 1.000kg

T 0.000kg

PT 0.000kg

N 1.000kg

(3 blank lines)

DATE: 2008 / 02 / 25

TIME: 14 : 30 : 00

TICKET NO .0003

G 1.000kg

T 0.000kg

PT 0.000kg

N 1.000kg

(3 blank lines)

DATE: 2008 / 02 / 25

TIME: 14 : 30 : 00

TOTAL NUMBER

OF TICKETS 0003

TOTAL

NET 3.000kg

(3 blank lines)

RTC setting , the form is the same with

Press key to transmit (complete mode) (The date and time will notbe transmit without mini printer.)

English

4-key serial 15 or 12-key serial



Press or key

Press or key



Besides English, the model is able to choose Traditional Chinese as printingform.

DATE: 2008 / 02 / 25

TIME: 14 : 30 : 00

TICKET NO .0001

G 1.000kg

T 0.000kg

N 1.000kg

(3 blank lines)

DATE: 2008 / 02 / 25

TIME: 14 : 30 : 20

TICKET NO .0002

G 1.000kg

T 0.000kg

N 1.000kg

(3 blank lines)

DATE: 2008 / 02 / 25

TIME: 14 : 30 : 40TICKET NO .0003

G 1.000kg

T 0.000kg

N 1.000kg

(3 blank lines)

DATE: 2008 / 02 / 25

TIME: 14 : 31 : 10

TOTAL NUMBER

OF TICKETS 0003

TOTAL

NET 3.000kg

(3 blank lines)

8/13/2019 20091218112714 j Yee 1 z

25/40

FB530/FB630 ZSME30000015923


RS232 and mini pr inter data transmission format in HOLD condition

Please set in .

When is set as or

, 1.000kg models format is as follows.

The format is as follows for 1.000kg model.

1 . 0 0 0 k g 0D 0A

PN (part No. )SN (Serial No.)

Setting Methods

Press and hold key for two seconds to enter in weighing mode.

About onesecond

6 Press and key to input12 sets of Part number.

About onesecond

6 Press and key to input12 sets of Serial number.

Remarks1. PN and SN values will come back to zero when power off.2. The type of mini printer is different for different languages.

Press key once, SN value willincrease one digit.

Press key once,PN value is fixed.

8/13/2019 20091218112714 j Yee 1 z

26/40

FB530/FB630 ZSME30000015924


Self-test Function of Printer (optional)Press and hold key to automatically print self-test data.

------------VERSION 10004010 Program version

DATE 2000/01/04 Printer dateTIME 200650 Printer time

MODE TAIWAN Printer language

MEMORY TEST OK Printer status

The test of Printer

1. Press and hold key to enter into.

Default20

2. Press or key to adjust the number.

3. Press key to print.4. Input the proper number to adjust the distance.

(large distance, adjust high)

(goodstandard)

(short distance, adjust low)

5. Press key to power on.

8/13/2019 20091218112714 j Yee 1 z

27/40

FB530/FB630 ZSME30000015925


Exit Setting Mode

Press or key to select F6function the display shows

Press key

Counting down tozero and exit setting

mode

8/13/2019 20091218112714 j Yee 1 z

28/40

FB530/FB630 ZSME30000015926


Weight Hold Mode setting

Under hold mode, press key to print the hold value showed.

(Select proper baud rate according to receiver and F5 transmission mode does not affect)

(Refer to F5 for details of transmission rate)

Please make sure MINI JUMPER of SWA1 is connected to ADJ on PC board before setting.

Please make sure MINI JUMPER of SWA1 is connected to LOCK on PC board after setting.


Press key in order and the displayshows accordingly

~Select required hold mode and then press

key to finish setting.

Press key

Press key

Press key

Press key

Press key

Press key

8/13/2019 20091218112714 j Yee 1 z

29/40

FB530/FB630 ZSME30000015927


Animal scale hold mode setting

Choose hold 4

Press key

Setting Error Range

Press and keys to set error rangefrom 1% ~ 100%Default setting: 10%

%

Average Trade Count Setting

Press and keys to set from 1.2.4.8.16.32.64.Default setting: 8

%

Press key

Press key

Press key

Press key

Press key

Hold functionDisableWhen the weight keeps changing, the indicator will automatically hold

and display the largest value.

Press any key except key to clear the hold value.

When the indicator becomes stable, the display shows and holds theweight value, which can not be changed.

Press any key except key to clear the hold value.

When the indicator becomes stable, the display shows and holds the

weight value, which can not be changed.

When the indicator is re-zeroed (weight less than 10d), the hold value is

automatically cleared.

Animal scale. When the animal is on the platter, the display shows the

weight value, which can not be changed.

When the animal leaves the platter (weight less than 10d), the indicator is

re-zeroed automaticall .

8/13/2019 20091218112714 j Yee 1 z

30/40

8/13/2019 20091218112714 j Yee 1 z

31/40

FB530/FB630 ZSME30000015929

EXCELL PRECISION CO., LTD.Load Cell Pin Description (input signal)

1. EXC+2. EXC-3. SIG+4. SIG-5. Shield

4-wire or 5-wire Load Cell (L/C)FB model

JP 21,JP 22 Short

PCB L/C

(E+) connect to EXC+

(E -) connect to EXC -

(S+) connect to SIG+

(S -) connect to SIG -

(FG) connect to Shield

Note: JP 21 and JP 22 are on the PCB in FB Model.

8/13/2019 20091218112714 j Yee 1 z

32/40

FB530/FB630 ZSME30000015930


Option Function DescriptionRS-232 output description (for FB model)

1. RS-232 OPTION Card : AD05135 = > 4 PIN connect to CN8 of main board

2. Please refer to F5 function settings for transmission mode, baud rate setting and data

format.

3. RS-232 (DB 25PIN) Pin Description

J1, J3 SHORT; J2, J4 OPEN (default setting)

Pin 2 RXDPin 3 TXDPin 7 GNDOther pins are disabled.

J2, J4 SHORT; J1, J3 OPEN

Pin 2 TXDPin 3 RXDPin 7 GNDOther pins are disabled.

Error MessagesOL The scale is over full scale +9d.

E1 Zero value after power on is over 10% FS when JP5 on the PCB in FB model is short.

E2 Zero value after power on is less than10% FS when JP5 on the PCB in FB model is short.

E4 Re-zero is unstable. When it is over 10 seconds, press 0 to exit E4.

E6 Zero value is over 550 000 when calibrating.

E7 Zero value is less than 150 000 when calibrating.

E10 LEVEL Switch Function: JP2 on the PCB in FB model is open, connect the signal toCN1. When CN1 is open, the display will disappear and then show E10. When CN1 is short, the

scale can be weighed in general condition. If not using LEVEL Switch Function, please JP2 is

set to be short.

8/13/2019 20091218112714 j Yee 1 z

33/40

FB530/FB630 ZSME30000015931


Appendix 1 ASCII Code Table

Symbol ASCII Code Symbol ASCII Code Symbol ASCII Code

A 41H a 61H 0 30H

B 42H b 62H 1 31H

C 43H c 63H 2 32H

D 44H d 64H 3 33H

E 45H e 65H 4 34H

F 46H f 66H 5 35H

G 47H g 67H 6 36H

H 48H h 68H 7 37H

I 49H i 69H 8 38H

J 4AH j 6AH 9 39HK 4BH k 6BH 0DHL 4CH l 6CH

M 4DH m 6DH

N 4EH n 6EH

O 4FH o 6FH

P 50H p 70H

Q 51H q 71H

R 52H r 72HS 53H s 73H

T 54H t 74H

U 55H u 75H

V 56H v 76H

W 57H w 77H

X 58H x 78H

Y 59H y 79H

Z 5AH z 7AH

8/13/2019 20091218112714 j Yee 1 z

34/40

FB530/FB630 ZSME30000015932


Appendix 2 7-Segment Display CharactersNumber Display Letter Display Letter Display

0 A N

1 B O

2 C P

3 D Q

4 E R

5 F S

6 G T

7 H U

8 I V

9 J W

K X

L Y

M Z

8/13/2019 20091218112714 j Yee 1 z

35/40

FB530/FB630 ZSME30000015933


Appendix 3 Printer InstallationA. Roll paper installation and problems solution1. Installation roll paper:

Use designated roll paper with a width 44.5 0.5 mm and internal diameter 50 mm.

Fix the roll paper into the paper entrance of the Printer. Cut the edge of the paper leveling and then install the paper (refer to Vof picture A).

And then use Feedkey to complete installation (make sure the paper is parallel with the

printing location. Avoid operating as Xof picture A )

The paper should not be folded or broken.

2. Uninstall roll paper:

Cut up the paper at the entrance of Printer, and then

pull out the paper from the exit of Printer.

3. Paper jam solutions procedures:

Uninstall the paper first.

Use a nipper or others to clear remain wastepaper.

B. Ribbon installation Use designated ribbon. (ERC-05)

Uninstall the roll paper before install the ribbon. (Picture B)

Turn and tighten the ribbon before installation.

Sway the ribbon to proper location according to Picture C.

If the ribbon loosens during installation, retighten

it according to Picture D.

To uninstall the ribbon, press gently the location in Picture E,and then take it out with proper adjustment.

The ribbon of the model received may deviate its location during

its transportation, and this may lead to the breakdown of the Printer.

To solve this problem, reinstall the ribbon according to the

above procedures.

Picture E

Picture D

Picture C

Picture B

Picture A

8/13/2019 20091218112714 j Yee 1 z

36/40

FB530/FB630 ZSME30000015934


Appendix 4 Load Hook InstallationPlease install the load hook (only for FB-630) according to correct order as follows.

8/13/2019 20091218112714 j Yee 1 z

37/40

8/13/2019 20091218112714 j Yee 1 z

38/40

8/13/2019 20091218112714 j Yee 1 z

39/40

8/13/2019 20091218112714 j Yee 1 z

40/40

20091218112714 j Yee 1 z

Documents

Transcript of 20091218112714 j Yee 1 z