APACHE 700XR/A HANDLEIDING
APACHE 700XR/A MANUAL
NL -
UK -
P. 02
P. 18
V2.4 EU
ALERT UNIT
W W W . A P A C H E 7 0 0 X R . C O M
2
Snel aan de slag
De Apache 700XR/A werkt met zowel abonnement als prepaid Sim kaarten. Indien u een
prepaid kaart gebruikt, let er dan op dat u een provider neemt waarbij het beltegoed niet verloopt of zo lang mogelijk bruikbaar is. Sommige prepaid kaarten dienen 1 x per jaar
opgewaardeerd te worden.
Zorg dat de kaart al geactiveerd is voordat u deze in de Apache 700XR/A plaatst en dat de voicemail is uitgeschakeld, de Apache 700XR/A is dan gelijk klaar voor gebruik.
Wacht na het aansluiten van de spanning op unit tot de groene LED continu brandt. (Dit
duurt 2 á 3 minuten!)
De groene LED geeft aan dat de Apache 700XR klaar is voor gebruik en u kunt de Apa-che 700XR/A door middel van de commando‟s (zie pagina 10 en 11) programmeren.
Indien de groene LED knippert, is er geen werkende sim kaart geïnstalleerd. De rode LED dient rustig te knipperen en geeft hiermee aan dat de unit volledig actief is.
Aansluitingen voor voeding, interface en antennes:
1. Aan/uit knop.
2. Connector voor de GSM antenne. 3. Led's GSM signaal en werking unit.
4. 9-pole (female) SUB-D plug voor RS-232 serial interface. 5. Optie, voor toekomstige toepassingen. 6. 24-polige GPIO 3mm Micro Mate-N-LOK Connector voor aansluiting op schakel-
contact, GPIOs, I²C, ADC. 7. 4-pole 3mm Micro Mate-N-LOK connector voor aansluiting adapter.
8. 6-pole RJ11 plug (niet gebruikt in Alert) 9. SIM kaart houder.
Technische gegevens:
700XR/A The 700XR/A module handelt alle processen voor
audio, signaal en data in de APACHE 700XR/A af. GSM frequentie: Quad band: GSM 850/900/1800/1900MHz
Voeding: 5-24Vdc Werktemperatuur: -20°C tot +70°C Afmetingen: 98mm x 82m x 30m
Gewicht: 160g RoHS, WEEE: Alle hardwarecomponenten zijn volledig
overeenstemmend met de EU RoHS en WEEE richtlijnen
3
5 4 3 2 1
7 6 Vooraanzicht
Zijaanzicht A
8
Zijaanzicht B 9
Onderkant
4
Blok-
schema
700XR/A
RS232
aan/uit Knop
Audio
3w Amp Speaker
Microfoon
Amp
SIM
DC naar
Dc
LIPI Batterij 900ma/H
4 pin
6 pin
Relay
PC Com/ RS232
8 GPIO
4 GPIO
Power
3.8V , PWRMON 2.8v
2 Pins
2 inputs ADC1, ADC2
2 Pins
2 Pins
GROUND
Antenne GSM
Speaker 4 ohm Microfoon
SMA
Batterij lader Optie
24 pin
9 pin
ADC3
GND
Input / Output Power 5-24VDC
4 GPIO - Open collector Voor Relais, LED
8 GPIO Inputs voor Sensoren
Output via Relais Totaal gescheiden GND
5
Voeding
De voeding van de APACHE 700XR/A dient 5-24Vdc te zijn en in staat te zijn om een
piek te kunnen leveren tijdens een actieve schakeling.
Een interne zekering zorgt voor veilige elektrische overdracht, volgens EN60950. Deze zekering is niet vervangbaar. Het toepassen van een smeltzekering in de APACHE
700XR/A wordt geadviseerd indien gebruik wordt gemaakt van voertuigen met 24Volt spanning, zoals vrachtwagens. De voeding moet overeenstemmend zijn met de EN60950-richtlijnen.
LET OP: DE VOEDING IS INTERN DOORGELUST VAN DE 4-PINS CONNECTOR NAAR DE
24-PINS CONNECTOR. INDIEN U DE ADAPTER GEBRUIKT, DIENT U ERVOOR TE ZORGEN DAT DE RODE EN ZWARTE DRAAD VAN DE 24-PINS CONNECTOR GEEN SLUITING KUN-
NEN MAKEN
De DC voeding moet in verbinding staan met de POWER input:
Input voltage range 5 - 24V DC
Nominaal voltage 12V DC
Voeding: min. 1,2A @12V
Voeding rimpel: max. 120mV
Voeding amperage in standby mode: 20mA @ 12V
Voeding amperage in communicatie mode: 100mA @ 12V
Pin Signaalnaam Gebruik
1 Voeding Input Power supply range 5-24Vdc
2 Reserve 3 GND Ground
4 Reserve
1 2
4 3
6
IO interface
24
12
13
1
GPIO 24 PIN
Pin Signaal naam I/O Omschrijving
1 Input1 I Input GPIO3 met Pull-up 4.7K
2 Input2 I Input GPIO4 met Pull-up 4.7K
3 Input aan I Input GPIO1 met Pull-up 4.7K
4 Input3 I Input GPIO8 met Pull-up 4.7K
5 Output4 O Output GPIO7 met 500ma max open collector
( ULM2003 )
6 Output1 O Output GPIO2 met 500ma max open collector
( ULM2003 )
7 Output2 O Output GPIO5 met 500ma max open collector
( ULM2003 )
8 Output3 O Output GPIO6 met 500ma max open collector
( ULM2003 )
9 EMEROFF I Wanneer aan GND gehaakt, zal het de interne
stroomvoorziening uitschakelen
10 Reserve I
11 VMOD O Modem voeding normaal 3.8V of batterij stroom
12 GND Ground
13 Relais_a O Normally open Relay leg 1 ( 30V 1A max)
14 Relais_b O Normally open Relay leg 2 ( 30V 1A max)
15 Input5 I Input GPIO12 met Pull-up 4.7K
16 Input4 I Input GPIO11 met Pull-up 4.7K
17 Input6 I Input GPIO15 met Pull-up 4.7K
18 Input7 I Input GPIO16 met Pull-up 4.7K
19 Reserve O
20 Reserve I
21 ADC1 I analog input 1
22 ADC2 I analog input 2
23 GND Ground
24 VIN I Input voeding +
7
Inputs De inputs worden als actief beschouwd, wanneer deze verbonden zijn met de GND (pin
12).
Open Collector Outputs De outputs zijn gelimiteerd tot de voedings spanning van de input. Wanneer de output niet geactiveerd is, heeft de open collector een hoge weerstand. Wanneer de open col-lector contact maakt met de GND is de ouput actief is (pin 12). Om een relais te schake-
len verbindt u de relais met de stroomvoorziening (Pin 24) en met de output.
Analoog naar Digitaal Converter (ADC) De twee analoge inputs worden gebruikt voor het meten van externe DC voltages met een bereik van 0V tot 5V. Let op: Alleen positieve voltages kunnen worden gemeten, door de input eisen van ADC.
Relais De interne Relais pins 13, 14 van de 24 pins interface connector kunnen gebruikt worden
om externe schakelingen of toepassingen te controleren.
Signaal naam 24 Pins connect-
or Omschrijving
Input1 1 Input met interne pull-up 4.7K
Input2 2 Input met interne pull-up 4.7K
Input3 4 Input met interne pull-up 4.7K
Input5 15 Input met interne pull-up 4.7K
Input4 16 Input met interne pull-up 4.7K
Input6 17 Input met interne pull-up 4.7K
Input7 18 Input met interne pull-up 4.7K
Signaal naam 24 Pins connect-or
Omschrijving
Output4 5 Output met 500ma max open collector
Output1 6 Output met 500ma max open collector
Output2 7 Output met 500ma max open collector
Output3 8 Output met 500ma max open collector
Signaal naam 24 Pins connector Omschrijving
ADC1_IN Pin No. 21 Analoge input 1 naar 700XR/A
ADC2_IN Pin No. 22 Analoge input 2 naar 700XR/A
8
Functie Uitvoering
8 inputs
8 input (1 input wordt gebruikt als master om alle 7 inputs in en uit te schakelen)
Mogelijkheid 1 input activeert alle inputs
Elke input stuurt een SMS naar de lijst van gebrui-
kers bij activatie.
Optie om per iedere input een spraakoproep te ma-
ken.
Inputs kunnen worden geactiveerd door SMS.
4 open collector outputs
4 outputs, elk 250ma, gelimiteerd door voedingsniveau van de inputs. Output kan geactiveerd worden op een aantal
manieren:
Output kan de volgende input activeren
Output activeert met een timer
AAN / UIT door middel van een SMS commando
1 interne relais
1 relais 1A 30V maximaal
Wanneer de gebruiker een spraakoproep maakt,
wordt deze een paar seconden aangezet.
2 inputs A/D extern
2 inputs voor 2- 4 mA sensoren
Iedere ADC is ingesteld om een SMS te versturen bij
een instelbaar overschrijdingspunt.
1 inputs A/D intern 1 input voor interne sensoren voor temperatuur
Simpele NTC sensor
Unit setup
Unit setup via speciale software d.m.v. RS232 en CSD of via SMS
Directe verbinding met PC via RS232
CSD verbinding met Apache 700XR modem
SMS via speciale commando‟s
9
Rode LED status Toestel status
Permanent aan Oproep is gaande
Snel knipperend (tussen de 0,5 sec tot 1
sec)
Bezig met GSM-netwerk zoeken / Niet
geregistreerd / Toestel wordt uitge-schakeld
Langzaam knipperend (tussen de 0,3s tot 3 sec)
Geregistreerd op het GSM-netwerk
Permanent uit Toestel staat uit
Groene LED status Toestel status
Permanent aan Toestel gereed voor oproep
Snel knipperend (tussen de 0,5 sec tot 1 sec)
Fout
Langzaam knipperend (tussen de 0,3 sec tot 3 sec)
Toestel ontvangt een oproep
Permanent uit Toestel staat uit
Rode LED geeft status van unit weer.
Groene LED geeft status van GSM netwerk weer.
Mechanische eigenschappen
Gewicht 160g
Afmetingen (max) L x W x H 98 mm x 82mm x 30mm
Werkzame temperatuur -20°C to +70°C omgevings temperatuur
IP-waarde IP40 Voorkom gebruik van Apache 700XR/A in
vochtige omgeving.
Mechanische vibratie Amplitude 7.5mm at 5-200Hz sinus
Luchtvochtigheid 5% - 85%
Klasse vlambaarheid UL94 HB
Behuizing PC/ABS Cycoloy 1200 HF
10
SMS Commando’s
1.1 Wachtwoord
Elke SMS start met het ingeven van het wachtwoord (standaard 1234)
Voorbeeld: P.1234A.0541122333.0544455666
Het commando P. het wachtwoord is 1234
Het commando A. is het toevoegen van een nieuw telefoonnummer aan de telefoonlijst,
in dit voorbeeld: 0541122333 en 0544455666
1.2 Toevoegen van een nieuw telefoonnummer
A.telefoonnummer.telefoonnummer…..
Het toevoegen van nieuwe telefoonnummers aan de telefoonlijst
Types: 1-hoofdgebruiker, 2-basisgebruiker
Voorbeeld 1: P.1234A.0547512152.1 Voegt 0547512152 aan de telefoonlijst toe, met als type „hoofdgebruiker‟.
Voorbeeld 2: P.1234A.0547512152.2 voegt 0547512152 aan de telefoonlijst toe, met als type „basisgebruiker‟.
1.3 Verwijderen van een telefoonnummer
D.telefoonnummer.telefoonnummer
Het verwijderen van telefoonnummers uit de „gewone‟ telefoonlijst.
Voorbeeld: P.1234D.0542684284.0542358721
Telefoonnummer 0542684284 en 0542358721 worden verwijderd uit de „gewone‟
telefoonlijst.
Indien er meer nummers tegelijk uit de telefoonlijst moeten worden verwijderd plaats
dan een punt tussen de telefoonnummers, de maximale SMS lengte kan worden
gebruikt.
1.4 Stel actieve input in SZA.input nummer input nummer
Stelt actieve input lijst in, van input 1 tot 7. Wanneer het inputnummer verschijnt is de input actief.
Voorbeeld: SZA.157 Input nummer 1 actief, input nummer 5 actief, input nummer 7 actief.
Input nummers 2,3,4,6 niet actief. 1.5 Stel input parameters in
SZP.input nummer.input vertraging.laag naar hoog.telefoon nummer.input naam
Stelt input parameters in, stelt inputnummer in, stelt input vertraging in, stelt input naam in
Voorbeeld: SZP.1.2H3M6S.1.0548420541.VOORDEUR Input nummer: 1 Vertragingstijd: 2 uur 3 minuten 6 seconden
Laag naar hoog detectie Detectie telefoonnummer: 0548420541
Input naam: VOORDEUR
11
Voorbeeld 2: SZP.5.8M.0.052541814.raam
Input nummer: 5 Vertragingstijd: 8 minuten
Hoog naar laag detectie Detectie telefoonnummer: 052541814
Input naam: raam 1.6 Stel output parameters in
sop.output nummer.output modus.output modus parameter Stelt de richtings modus voor de geselecteerde output nummer 1-4, selecteert 0 van
hoog naar laag of 1 van laag naar hoog. Voorbeeld 1: SOP.1.1.1
Output number: 1 Output modus: 1 à Hoog/Laag Output modus parameter: 1 à hoog
Voorbeeld 2: SOP.3.2.3M2S
Output nummer: 3 Output modus: 2 à één keer, op aanvraag, time-out Output modus parameter: 3M2S à 3 minuten 2 seconden
voorbeeld 3: SOP.2.3.1H2S
Output nummer: 2 Output modus: 3 à door input detectie, time-out
Output modus parameter: 1H2S à 1 uur 2 seconden
Voorbeeld 4: SOP.4.4.15S Output nummer: 4
Output modus: 4 à Alarm – Alle inputs Output modus parameter: 15S à 15 seconden
Voorbeeld 5: SOP.1.5.1M Output nummer: 1
Output modus: 5 à Buzzer Output modus parameter: 1M à 1 minuut
1.7 Nieuw wachtwoord
NP.nieuw wachtwoord
Het instellen van een nieuw wachtwoord van de APACHE 700XR/A. (bewaar deze goed,
deze is van belang bij elke instelling die gewijzigd moet worden. Bij zoek raken van het
wachtwoord moet de module retour naar de leverancier)
Voorbeeld: P.1234NP.4321. Het wachtwoord wordt veranderd in 4321
1.8 Haal versienummer op
VER Vraagt de softwareversie aan.
1.9 Haal GSM ontvangst op RECEP Vraagt het ontvangstniveau van de GSM aan.
12
Programmeren middels software
5. 4.1 4.2 1. 3. 2.
Nummer Omschrijving
1 Communicatie selectie COM 1-16 of Modem via CSD
2 Taal instelling
3 Verbind met unit
4.1 Opslaan
4.2 Opslaan als …
5 Back-up openen vanaf de computer
Stel de Apache 700XR/A unit in via RS232 of via modem.
Om de gewenste verbinding te kiezen dient u te klikken op het icoon van de
communicatie selectie
Selecteer RS232 COM port van 1-16 of Modem voor connectie.
Om verbinding te maken via RS232, klik op het verbind-met-unit-icoon.
Om een andere taal te kiezen, klik op het taal-instelling-icoon.
Om alle data op te slaan voor een back-up, klik op het icoon van opslaan.
Om een back-up te openen, klik om het icoon van back-up openen
13
Telefoonnummer toevoegen
50 telefoonnummers kunnen aan de unit toegevoegd worden. Deze kunnen als
hoofdgebruiker of als basisgebruiker aangewezen worden.
Hoofdgebruikers krijgen een SMS alert van de inputs en kunnen de relais behe-
ren door middel van een telefoontje.
Basisgebruikers kunnen alleen de relais beheren.
Aan de gebruikerslijst kan een naam worden gegeven en vervolgens worden op-
geslagen als een EXCEL lijst. Deze kunnen vervolgens ook weer geïmporteerd worden.
14
Beheer Inputs en Outputs
Instellingen voor inputnaam en activering, stel inputvertraging in. Als de inputvertraging
bijvoorbeeld 5M is, betekent dat dat de input inactief is gedurende 5 min. na activering.
Stel telefoonnummer voor de unit in om een spraakoproep te doen als de input activeert.
Stel OPEN COLLECTOR outputs in, stel outputs modus in.
Output modus:
Hoog/Laag:
Output parameter: 0 - Deactiveert de output, wat betekent dat de open collector een hoge weer stand heeft.
1 - Activeert de output, betekent dat de open collector verbonden is met GND. Éénmaal, op aanvraag:
Gebruik deze mogelijkheid niet met de software, alleen met SMS. Door input detectie:
De overeenkomstige input activeert de output voor een periode bepaald door de output parameter. Output parameter: tijd ingeven: *U*M*S bijv. 1U3S = 1 uur 3 seconden.
Alarm: Alle inputs activeren de output voor een bepaalde tijdsperiode, bepaald door
de output parameter. Output parameter: tijd ingeven: *U*M*S bijv. 5M3S = 5 minuten 3 seconden. Buzzer:
Geeft aan dat een zoemer aangesloten is op de output. De unit gebruikt deze output om een activatie of deactivatie aan te geven van
de “input enable” of “Bellen” (Volgens de “input Activatie Modus” in de diverse instellingen).
15
A/D Instellingen
Stel parameter voor elke A/D input in
Parameter kunnen aangepast worden voor input voltage bereik of input huidig
bereik verschillend voor het type unit.
Stel een SMS notificatie in wanneer de hoogste of laagste waarden worden over-
schreven
Stel een naam van de parameter en gemeten symbol in
Stel een SMS bericht in voor wanneer het input voltage beneden de 6V komt
Stel een SMS bericht in voor wanneer het input voltage weer terug boven de 6V
komt.
16
Diverse instellingen
17
Op deze pagina kunt u alle diverse instellingen instellen die de XR/A activeren.
Unit naam: De naam van de unit.
Unit tijd: stelt de tijd in voor „speciale‟ telefoonnummers en log.
Unit wachtwoord: verandert het wachtwoord. Is hetzelfde wachtwoord voor de
SMS als voor de RS232 of CSD connectie.
Input activerings modus: activeert of deactiveert de inputs door “Enable PIN”
of door middel van een telefoontje.
Klok update SMS: unit kan de tijd doorkrijgen door eigen SMS, hier dient u het
nummer in te vullen van de unit. Bij spanningsuitval zal de unit zichzelf een SMS
sturen wanneer de unit weer online is. De tijd van de unit wordt dan weer ingesteld met de tijd uit de SMS.
Band selectie: 4 opties voor de band selectie van Europa en Noord Amerika.
Versie: De unit software versie.
Ontvangst: geeft het ontvangstpercentage weer van de unit. Onder de 30%
wordt gezien als zwak ontvangst. Verandering van de plaats van de antenne kan
zorgen voor beter ontvangst.
Schakeltijd: geeft de schakelduur van het relais weer. (maximaal 60 seconden).
Vertragingstijd: De unit stelt deze automatisch in op 3 seconden, gebruik dit
veld voor een andere vertraging.
Input gevoeligheid: Stelt het aantal keer schakelen van een input in voordat
het beschouwd wordt als een inputverandering.
Parts United verklaart dat het product, Apache 700XR EZ863 PY Ter-
minal, Voldoet aan de essentiële eisen van de 89/336/EEC richtlijn. De volgende standaarden zijn toegepast:
EMC EN 55022:1994 + A1:1995 + A2:1997 EN 55024: 1998 + A1:2001 + A2:2003
EN50081-1 : 1998 Emissie test EN55022 Klasse B EN55024 : 1998 Immunity testen Veiligheid IEC 60950-1:2001
De volledige verklaring van conformiteit is beschikbaar op de website: http://www.apache700xr.com/ce
18
Quick start
The Apache 700XR/A works with contract as well as prepaid Sim cards. When using a
prepaid card, notice that some providers let the call credit expire after a certain time. Some prepaid cards have to be upgraded once a year.
Be sure the card is activated by your provider before you insert the card in the
Apache 700XR/A. Also, disable the PINcode and the voicemail, than the Apache 700XR/A is immediately ready for use.
After connecting the voltage with the Apache 700XR/A wait till the green LED is perma-nently on. (It takes 2 or 3 minutes).
A green LED that is permanently on indicates that the Apache 700XR/A is ready for use.
You can programm the Apache 700XR/A by the commands described at page 26 and 27. When the green LED has a interrupt sequence, the installed Sim card is not working or
there is no contact with the provider of the Sim card. The red LED should have a slow interrupt sequence, this indicates that the unit is completely activated.
connectors for power supply, interface and antennas:
1. On/Off push button.
2. SMA connector (female) for GSM antenna. 3. Led's GSM and Unit.
4. 9-pole (female) SUB-D plug for RS-232 serial interface. 5. Option, Not in use. 6. 24-pole GPIO 3mm Micro Mate-N-LOK connector for cable.
7. 4-pole 3mm Micro Mate-N-LOK connector for power supply. 8. 6-pole RJ11 plug (Not in use with the Apache 700XR/A).
9. SIM card holder.
Key Features of the Apache 700XR/A Terminal:
Frequency bands: Quad band: GSM 850/900/1800/1900MHz
Power supply: 5-24Vdc Operating temperature: -20°C tot +70°C
Dimensions: 98mm x 82m x 30m Weight: 160g RoHS, WEEE: All hardware components are fully compliant with the EU
RoHS and WEEE Directives
19
5 4 3 2 1
7 6 Front view
Side A view
8
Side B view 9
Bottom view
20
Block-
schedule
700XR/A
RS232
on/off button
Audio
3w Amp Speaker
Microphone
Amp
SIM
DC to Dc
LIPI Battery 900ma/H
4 pin
6 pin
Relay
PC Com/ RS232
8 GPIO
4 GPIO
Power
3.8V , PWRMON 2.8v
2 Pins
2 inputs ADC1, ADC2
2 Pins
2 Pins
GROUND
Antenna GSM
Speaker 4 ohm Microphone
SMA
Battery charger Option
24 pin
9 pin
ADC3
GND
Input / Output Power 5-24VDC
4 GPIO - Open collector for Relay, LED
8 GPIO Inputs for Sensors
Output via Relay Total seperated GND
21
Voeding
The power supply of the Apache 700XR/A Terminal has to be a single voltage source of
POWER 5V-24Vdc capable of providing a peak during an active transmission.
The Apache 700XR/A Terminal is protected from supply voltage reversal. An internal fuse ensures an electrical safety according to EN60950. This fuse is not removable. A fast
acting fuse 0.8A with melting is necessary to use with the Apache 700XR/A Terminal at a 24V power supply system for vehicles. The power supply must be compliant with the EN60950 guidelines.
NOTE: THE POWER SUPPLY IS INTERNALY CONNECTED FROM THE 4-PINS CON-
NECTOR TO THE 24-PINS CONNECTOR. IF YOU USE THE ADAPTER, YOU HAVE TO MAKE SURE THAT THE RED AND BLACK WIRE OF THE 24-PINS CONNECTOR DO
NOT CONNECT!
The DC power supply must be connected to the POWER input:
Input voltage range 5 - 24V DC
Nominal voltage 12V DC
Power Supply current rating: min. 1,2A @12V
Power Supply ripple: max. 120mV
Input current in idle mode: 20mA @ 12V
Input average current in communication mode: 100mA @ 12V
Pin Signalname Use
1 Input power Input Power supply range 5-24Vdc
2 Reserve 3 GND Ground
4 Reserve
1 2
4 3
22
IO interface
24
12
13
1
GPIO 24 PIN
Pin Signal name I/O Description
1 Input1 I Input GPIO3 with Pull-up 4.7K
2 Input2 I Input GPIO4 with Pull-up 4.7K
3 Input enable I Input GPIO1 with Pull-up 4.7K
4 Input3 I Input GPIO8 with Pull-up 4.7K
5 Output4 O Output GPIO7 with 500ma max open collector
( ULM2003 )
6 Output1 O Output GPIO2 with 500ma max open collector
( ULM2003 )
7 Output2 O Output GPIO5 with 500ma max open collector
( ULM2003 )
8 Output3 O Output GPIO6 with 500ma max open collector
( ULM2003 )
9 EMEROFF I When hook to GND will power off the internal power
supply
10 Reserve I
11 VMOD O Modem power supply normally 3.8V or battery power
12 GND Ground
13 Relay_a O Normally open Relay leg 1 ( 30V 1A max)
14 Relay_b O Normally open Relay leg 2 ( 30V 1A max)
15 Input5 I Input GPIO12 with Pull-up 4.7K
16 Input4 I Input GPIO11 with Pull-up 4.7K
17 Input6 I Input GPIO15 with Pull-up 4.7K
18 Input7 I Input GPIO16 with Pull-up 4.7K
19 Reserve O
20 Reserve I
21 ADC1 I analog input 1
22 ADC2 I analog input 2
23 GND Ground
24 VIN I Input Power Supply +
23
Inputs The inputs are considered active when connected to GND (pin 12).
Open Collector Outputs The outputs are limited to the power supply input voltage.
When the output is not active the open collector is high impedance. When the output is active, means the open collector is short to the GND (pin 12). To switch a relay, connect the relay to the power supply (Pin 24) and to the output.
Analog to Digital Converter (ADC) The two analog inputs are used for measuring external DC voltages in a range of 0V to
5.0V. Note: Only positive voltage can be handled because of the input requirement of ADC.
Relay The internal Relay pins 13,14 at the 24 pins interface connector may be used for control-
ling external circuit devices or applications.
Signal name 24 Pins connect-
or Description
Input1 1 Input with internal pull-up 4.7K
Input2 2 Input with internal pull-up 4.7K
Input3 4 Input with internal pull-up 4.7K
Input5 15 Input with internal pull-up 4.7K
Input4 16 Input with internal pull-up 4.7K
Input6 17 Input with internal pull-up 4.7K
Input7 18 Input with internal pull-up 4.7K
Signal name 24 Pins connect-or
Description
Output4 5 Output met 500ma max open collector
Output1 6 Output met 500ma max open collector
Output2 7 Output met 500ma max open collector
Output3 8 Output met 500ma max open collector
Signal name 24 Pins connector Description
ADC1_IN Pin No. 21 Analoge input 1 to 700XR/A
ADC2_IN Pin No. 22 Analoge input 2 to 700XR/A
24
Feature Implementation
8 Inputs
8 input Inputs pull up ( 1 Input use as master enable for all the 7 Inputs )
Enable Input activate all Inputs
Each Input send SMS to list of users when activate
Option each Input can set voice call to different
user
Inputs can be activate by user SMS
4 open collector outputs
4 outputs 250ma each, limited to power supply input volt-age
Output can be activate in few modes:
Output can activate following Input activate
Output activate with timer
ON / OFF by SMS command
1 internal relay
1 relay 1A 30V maximum
Set to be ON for few seconds when user make
voice call
2 inputs A/D external 2 inputs for 2- 4 mA sensors
Each ADC set to send SMS when crossing set point
1 inputs A/D internal 1 input for internal sensor for Temperature
Simple NTC sensor
Unit setup
Unit setup via special software to RS232 and CSD or via SMS
Direct connection to PC via RS232
CSD connection with GSM modem
SMS via special commands
25
Red LED status Device Status
Permanently on A call is active
Fast interrupt sequence (period 0,5 sec to 1
sec)
Net search / Not registered / turning
off
Slow interrupt sequence (period 0,3 sec to 3 sec)
Registered full service
Permanently off Device off
Green LED status Device status
Permanently on Unit Ready for calls
Fast interrupt sequence (period 0,5 sec to 1 sec)
Error
Slowly interrupt sequence (between 0,3 sec to 3 sec)
Unit receive a call
Permanently off Device off
Red LED displays the network status of the terminal.
Green LED displays the operating status of the network.
Mechanical Characteristics
Weight 160g
Dimensions (max) L x W x H 98 mm x 82mm x 30mm
Temperature range -20°C to +70°C ambient temperature
Protection class IP40 Avoid exposing Apache 700XR/A Terminal to
liquid or moisture.
Mechanical vibrations Amplitu-de
7.5mm at 5-200Hz sinus
Air humidity 5% - 85%
Class of flammability UL94 HB
Casing material PC/ABS Cycoloy 1200 HF
26
SMS Commands
1.1 PASSWORD
Every SMS starts with p:password Example: P.1234A.0541122333.0544455666
the command P. The password is 1234 the command A. is add new phone number 0541122333 and 0544455666
1.2 ADD NEW PHONE NUMBER A.phone number.user type
Add new phone numbers to the phone list Types: 1-master , 2-slave
Example 1: P.1234A.0547512152.1 Add 0547512152 to the phone list, its type is a master.
Example 1: P.1234A.0547512152.2 Add 0547512152 to the phone list, its type is a slave.
1.3 DELETE PHONE NUMBER
D.phone number.phone number Delete phone numbers from regular phone list Example: P.1234D.0542684284.0542358721
Phone number 0542684284 and 0542358721 deleted from the regular phone list, put comma between the phone numbers, can use all SMS size.
1.4 SET ZONE ACTIVE LIST
SZA.zone number zone number Set zone active list, from zone 1 to 7, when zone number appear the zone is active. Example: SZA.157
Zone number 1 active, Zone number 5 active, Zone number 7 active. Zone numbers 2,3,4,6 not active.
1.5 SET ZONE PARAMETERS
SZP.zone number.zone delay string.low to high.phone number.zone name Set zone parameters, set zone number, set zone delay string, set zone name Example: SZP.1.2H3M6S.1.0548420541.FRONT DOOR
Zone number: 1 Delay time: 2 hours 3 minutes 6 second
Low to high detection Detection phone number: 0548420541 Zone name: FRONT DOOR
Example2: SZP.5.8M.0.052541814.window
Zone number: 5 Delay time: 8 minutes
High to low detection Detection phone number: 052541814 Zone name: window
27
1.6 SET OUTPUTS PARAMETERS
sop.output number.output state.output state parameter Set the direction mode for the selected output number 1-4, select 0 high to low or 1
from low to high. Example 1: SOP.1.1.1
Output number: 1 Output state: 1 à High/Low Output state parameter: 1 à high
Example 2: SOP.3.2.3M2S
Output number: 3 Output state: 2 à Once, by request, time out
Output state parameter: 3M2S à 3 minutes 2 seconds Example 3: SOP.2.3.1H2S
Output number: 2 Output state: 3 à by zone detection, time out
Output state parameter: 1H2S à 1 hour 2 seconds Example 4: SOP.4.4.15S
Output number: 4 Output state: 4 à Alarm – All zones
Output state parameter: 15S à 15 seconds
Example 5: SOP.1.5.1M Output number: 1 Output state: 5 à Buzzer
Output state parameter: 1M à 1 minute
1.7 NEW PASSWORD
NP.new password Sets new password to the unit (the CSD password infect also) Example: P.1234NP.4321
Change the password to 4321
1.8 GET VERSION
VER Request the software version
1.9 GET GSM RECPTION
RECEP Request the GSM reception level
28
Programming through software
5. 4.1 4.2 1. 3. 2.
Number Description
1 Select connection COM 1-16 or Modem via CSD
2 Select language
3 Make connection to the unit via RS232
4.1 Save
4.2 Save as …
5 Open backup unit data from the PC file
Control the Apache 700XR/A unit via RS232 or CSD
To select the connection, push the phone icon number 1 on the top image.
Select RS232 COM port from 1-16 or Modem for CSD connection.
To make RS232 connection, push the icon number 3 on the top image.
To select different language, push the icon number 2 on the top image.
To save all unit data for backup, push the icon number 4 on the top image.
To open backup unit data, push the icon number 5 on the top image.
29
Add phone numbers
50 phone numbers add to the unit select user as master or secondary.
Master user get SMS alert from zones and can control the relay with call.
Secondary user can only control the relay.
User phone list and name can be exported and imported to EXCEL file.
30
Control Inputs en Outputs
Setting zone name and activation, set zone delay. If the zone delay is for example 5M, it
means the input is inactive for 5 minutes after activation.
Set phone number for unit to make VOICE call when the zone activates.
Setting OPEN COLLECTOR outputs, set outputs mode.
Output state modes:
High/Low:
Output state parameter: 0 - Deactivate the output, means the open collector is high impedance.
1 - Set the output to be active, means the open collector is short to the GND. Once, by request: Do not use this state with the software, only SMS.
By zone detection: The correspond input activate the output for a period of time determined by
the output state parameter. Output state parameter: time format: *H*M*S e.g. 1H3S = 1 hour 3 seconds.
Alarm: All the inputs activate the output for a period of time determined by the output state parameter.
Output state parameter: time format: *H*M*S e.g. 5M3S = 5 minutes 3 sec. Buzzer:
Indicate that a buzzer connected to the output. The unit will use this output to indicate an activation or deactivation of the
zones by “Zone enable” or “Ring” (according to the “Zone Activation Mode” in the miscellaneous section).
31
A/D Settings
Set parameter for each A/D input
Parameter can be set for input voltage range or input current range according to
the unit type.
Set SMS notification when passing high or low values
Set name of parameter and measured symbol
Set SMS message when input voltage goes below 6V
Set SMS message when input voltage goes back to above 6V
32
Miscellaneous
33
At this page set all miscellaneous options that will activate the APACHE 700XR/A.
UNIT NAME
UNIT TIME, set time for special phone number and log.
UNIT PASSWORD, change unit password,
The password applies to SMS, RS232 or CSD connection.
SELF CLOCK UPDATE SMS, on unit power up, unit can get the time from SMS
send to itself, fill-in the SIM number of the unit to this field.
BAND SELECTION, 4 options for band selection for EUROPE and North America.
ZONE ACTIVATION MODE, activate or deactivate the zones by the “Enable
PIN” input or by a call (Ring).
VERSION, get unit software version.
RECEPTION, get unit reception level under 30% will consider low level, try to
improve GSM antenna location for better reception.
GATE DELAY, unit set to 3 second normally, for different time delay set this box.
INPUT DEBOUNCE, set the amount of times to sample an input (zone) before it
will be considered it as an input change.
Parts United declares that the product, Apache 700XR EZ863 PY Ter-
minal, Fulfills the essential requirements of Directive 89/336/EEC. The following standards were applied:
EMC EN 55022:1994 + A1:1995 + A2:1997 EN 55024: 1998 + A1:2001 + A2:2003
EN50081-1 : 1998 Emission test EN55022 Class B EN55024 : 1998 Immunity tests Safety IEC 60950-1:2001
The complete declaration of conformity is available on the website: http://www.apache700xr.com/ce
34
Notes
35
Notities
36
Your dealer:
Top Related