Inst Checklist 0405

8/17/2019 Inst Checklist 0405

1/6

Agilent 1100 Series

Liquid Chromatograph

Hardware and Software Installation Checklist

Hardware / SoftwareUnpacking and inspection of

shipped materials

solvent inlet/outlet

Priming each channel withIsopropanol from solvent bottleto pump inlet

InstallationNote: Shipping containers shouldnot be opened until an AgilentTechnologies representative is present

Purpose: To ensure that instrumentsand systems are correctly installedand functioning as designed, in thecustomer's facility. Correctinstallation is the first step inensuring that instruments andsystems operate reliably over anextended lifetime.

G1310A/11A/12A – Pump

Section NOT Applicable Unpack all boxes and place equipment on bench. To prevent injury, get liftingassistance if needed.

1. SN/FW#_____________________

2. SN/FW#_____________________ Retain shipping containers andmaterial until installation iscomplete and performance is

verified

3. SN/FW#_____________________

Customer Responsibilities The customer should ensure that theinstallation site is prepared inaccordance with the specificationscontained in the relevant site preparation document and that thenecessary operating supplies,consumables and usage dependentitems such as vials, paper, solvents,etc. are available. A customerrepresentative should be present atall times during the installation.

Set up the pump(s) Notify order fulfillment of any

discrepancies solvent inlet/outlet waste drain

Unpack and verify conditionand completeness of shipment remote control (if used)

relay contacts (if installed) Check serial numbers and fill in

installation documentation S/Nfields if necessary

seal wash tubing(if installed)

CAN Verify that power cords are

correct (must mate with powersockets) and are plugged into power receptacle

Agilent GPIB/LAN (see note*) Priming the pump

prepare solvents

turn on

When applicable, installcomputer system and connect all power interconnect cables

Note: Typical installation time is

1.5 hours for a system and 30

minutes for a module.

purge purge mobile phase monitor the pressure

If a G1315C-DAD or G1365C-MWD is added to an existing1100 system, all modules must be upgraded to firmwarerevision A.06.xx using theLAN/RS-232 FW Update Tool2.00 according to the updatedocumentation.

If installation time was not sold forany section, check that section asnot applicable.

G1382A G1376A Capillary Pump

G1379A Micro Degasser

G2225A G2226A Nano pump

Issued: April, 2005 – Rev. 5.0 N/A WAD LPA Product Support Page 1 of 6

Installation Checklist G1379A Micro Degasser

Section NOT Applicable Section NOT Applicable

G1322A/79A– DegasserNote:

If one section contains multiplechoices for installed Hardware please encircle all modules that are part of the system and fill in thecorresponding Serial Number.

1. SN/FW#_____________________ Section NOT Applicable

2. SN/FW#_____________________ 1. SN/FW#_____________________

Set up the pump2. SN/FW#_____________________

solvent inlet/outlet waste drain

Set up the degasser(s) remote control (if used)


2/6

Agilent 1100 Series



5065-9922 Prep. Manual Injector


relay contacts (if installed)

CAN Agilent GPIB/LAN (see note*) set up the degasser solvent inlet/outlet priming each channel with

Isopropanol from solvent bottle to pump inlet

Priming the pump prepare solvents turn on purge purge mobile phase

monitor the pressure

G1361A – Prep. Pump

Section NOT Applicable

1. SN/FW#_____________________

2. SN/FW#_____________________

Set up the pump(s) solvent inlet/outlet waste drain

remote control (if used) relay contacts (if installed) seal wash tubing CAN Agilent LAN (see note*)

Priming a prep pump Prime each pump individually Use the syringe + adapter +

tubing and connect to the wasteoutlet of the pump`s EMPV

Turn ON the pump and

electronically switch the EMPVto waste Manually suck the solvent into

and trough the pump Pump at least 0.5 liter of IPA

through the pump

G1328A/B – Manual Injector or

G1327A - Thermostat. ALS

Section NOT Applicable G1389A - Thermostat. Micro ALSG1364A/B/C/D + G1330A/B

SN/FW#________________________ Therm. Fraction Collector G1368A - Thermostat. WPS Setup the injector G1378A - Thermostat. Micro WPS

start/stop cable to pump G2261A - Thermostat. Preparative base plate & mounting pole position valve inlet/outlet connected sample loop vent tubes

G1313A/29A – Autosampler

G1387A – Micro ALS

G1367A - Well Plate Sampler

G1377A - Micro WPS

G2258A – Dual Loop ALS

G2260A - Preparative ALS


1. SN/FW#_____________________

2. SN/FW#_____________________

3. SN/FW#_____________________

Setup the autosampler(s) solvent inlet/outlet waste drain (must be in a

straight line down, no bends, kinks or curves

large volume tube(if installed)

BCD output (if installed) remote control (if used) relay contacts (if installed)

CAN Agilent GPIB/LAN (see note*)

The following section applies if aG1330A/B - ALS Thermostat

is installed together with any of thewell-plate-, autosamplers or fractioncollectors to generate a:

ALS

G1330A/B - ALS Thermostat


1. SN/FW#_____________________

2. SN/FW#_____________________

3. SN/FW#_____________________

Setup the ALS Thermostat(s)underneath the module(s) thathas (have) to be thermostatted

WARNING: Do not connect theALS thermostat cable while the line power is connected to the anyof the modules. This would damage

the sampler or fraction collector andthe thermostat electronics. air channel adapter and plate ALS thermostat cable ALS thermostat waste drain

G1316A - Column Compartment


SN/FW#________________________

Setup the TCC solvent inlet/outlet column waste drain remote control (if used) CAN GPIB (see note*)


3/6

Agilent 1100 Series



G1157A/58A/59A/60A/62A/63A remote control (if used)

Valves



1. SN/FW#_____________________

2. SN/FW#_____________________

3. SN/FW#_____________________

Setup the Valves Setup the 1100 Series Valve solvent inlet/outlet

CAN CAN-DC-In from other 1100

Module (e.g. G1367A WPS,G1364A/B/C/D FractionCollector or G1361A Prep.Pump)

G1383A Column Organizer


SN/FW#________________________

Setup the column organizer base plate and organizer plate rods traversesadditional holders (if used)

G1314A – VWD


SN/FW#________________________

Set up the detector flow cell

solvent inlet/outlet waste drain remote control (if used) analog output (if used) relay contacts (if installed) CAN Agilent GPIB/LAN (see note*)

Verify the operation of the

detector

analog output (if used) CAN Agilent GPIB/LAN (see note*) Lamp

IntensityPass/Fail

Verify the operation of thedetectorZero-order

DeviationWLcalibration Lamp

IntensityPass/Fail656nm

DeviationExcitationDeviationG1315A/B/C-DAD / G1365A/B/C-

MWD


1. SN/FW#_____________________

2. SN/FW#_____________________

Set up the detector(s) deuterium lamp

(if not installed)

solvent inlet/outlet waste drain remote control (if used) analog output (if used)

relay contacts (if installed) CAN Agilent GPIB/LAN (see note*) Verify the operation of the

detector

LampIntensity

1.2.

Pass/Fail

1.2.WL

calibration 1.2.

AlphaDeviationBetaDeviation

G1321A – FLD Section NOT Applicable

SN/FW#________________________

Set up the detector solvent inlet/outlet waste drain

WLverification Emission

Deviation

G1362A – RID


SN/FW#________________________

Set up the detectorWARNING: Make sure that all plugs are removed from the portsand the appropriate capillaries(inlet/outlet/recycling) areconnected (maximum backpressure

of 5 bar for flow cell). solvent inlet/outlet solvent recycle waste drain remote control (if used) analog output (if used) CAN Agilent GPIB/LAN (see note*)

Verify the operation of thedetector

Diode

Balance Value

G1364A/B/C/D – Fraction

Collector


1. SN/FW#_____________________


4/6

Agilent 1100 Series



2. SN/FW#_____________________

3. SN/FW#_____________________

4. SN/FW#_____________________

Setup the fraction collector(s) solvent inlet/outlet waste drain remote control (if used) relay contacts (if installed) CAN Agilent LAN (see note*)

G1390A – Universal Interface Box

(UIB)


SN/FW#________________________

Setup the universal interface box

CAN Analog In (if used) GPIO / Analog In (if used) Relay Contacts (if used)

Note: Agilent GPIB/LAN connectionis made between one (1) of the Agilent

1100 Series System modules and the

Agilent ChemStation PC. If a

detector is installed connect the

GPIB/LAN to this module.



5/6

Agilent 1100 Series



Software Installation (Un- 1100 LC CheckoutG1323A/B – Control Module



SN/FW#________________________

Set up the control module Connect via CAN to

available instrument module

Software Installation (Bundled)


Software

Product:_________________________

SoftwareRevision:________________________

Start Windows Start ChemStations -> Add

Licenses and add the licensenumbers. You find thesenumbers in the 'SoftwareCertificate and RegistrationPacket' envelopes.

Configure TCP/IP if the

instrument will be connectedusing LAN.

Install and Configure IOLibraries if instrument will beconnected using GPIB.

If necessary install andconfigure AGILENT BootpService if the instrument will beconnected using LAN.

Use the Configuration Editorand configure your instruments.

Install and Configure Software

Add-Ons (if applicable) If present, install the PC Image

software and create a backupusing the Backup Solution UserGuide as reference.

Bundled)

Start a run Section NOT Applicable Prepare:

1. pump(s)SoftwareProduct:_________________________

2. online degasser (s)(if present)

3. injection device(s)SoftwareRevision:_____________________

4. column compartment5. detector(s)6. fraction collector(s)

(if present) Start Windows Install ChemStation using the

ChemStation Installation guide

for reference.

7. Valve(s) (if present)8. recording device

Attach results to installationdocumentation

Check if a printer driver isinstalled on the system

Fill out instrument logbook Verify that the regional settings

are set to English-US Install and Configure TCP/IP if

the instrument will be connectedusing LAN.

Install and Configure IOLibraries if instrument will beconnected using GPIB.

If necessary install and

configure AGILENT BootpService if the instrument will beconnected using LAN

Use the Configuration Editorand configure your instruments.


6/6

Agilent 1100 Series



Service Review


Note: Password is the Registration

number for the software Affix any reports generated tothis Checklist

Sales Order Number Record in the instrumentlogbook date and time installwas completed

_________________________

Customer Service Order (CSO) Number

Explain Agilent warranty forHardware, Software and return policy for the InstrumentService Center

__________________________

Date completed Explain how to log aninstrument service call __________________________

Explain support services

Customer Signature

Explain how to use manuals Advise customer of additional

training options __________________________

Advise the customer of thefollowing useful AgilentWebSites:

Support Provider Signature

__________________________ e.g. 1100 Series Firmware(Downloads/patches)

Exclusive offers:

www.agilent.com/chem/exclusiveoffers

Library -http://www.agilent.com/chem/library

Education -www.agilent.com/chem/education

eSeminars -www.agilent.com/chem/eseminars

Software Status Bulletins and Patches -www.agilent.com/chem/techsupport

Supplies - www.agilent.com/chem/supplies

Tech Support -

www.agilent.com/chem/techsupp

http://www.agilent.com/chem/exclusiveoffershttp://www.agilent.com/chem/libraryhttp://www.agilent.com/chem/educationhttp://www.agilent.com/chem/eseminarshttp://www.agilent.com/chem/techsupporthttp://www.agilent.com/chem/supplieshttp://www.agilent.com/chem/techsupporthttp://www.agilent.com/chem/techsupporthttp://www.agilent.com/chem/supplieshttp://www.agilent.com/chem/techsupporthttp://www.agilent.com/chem/eseminarshttp://www.agilent.com/chem/educationhttp://www.agilent.com/chem/libraryhttp://www.agilent.com/chem/exclusiveoffers

Inst Checklist 0405

Documents

Transcript of Inst Checklist 0405