Voorbeeld Preview - NEN 1011-5 Nederlands voorwoord Voor de in deze norm vermelde normatieve...
Click here to load reader
Transcript of Voorbeeld Preview - NEN 1011-5 Nederlands voorwoord Voor de in deze norm vermelde normatieve...
Vervangt NEN-EN 1011-5:2001 Ontw.
Nederlandse norm
NEN-EN 1011-5 (en)
Welding - Recommendations for welding of metallic materials - Part 5: Welding of clad steel
ICS 25.160.10
juni 2003
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Dit
do
cum
ent
mag
sle
chts
op
een
sta
nd
-alo
ne
PC
wo
rden
gei
nst
alle
erd
. Geb
ruik
op
een
net
wer
k is
alle
en.
toes
taan
als
een
aan
vulle
nd
e lic
enti
eove
reen
kom
st v
oo
r n
etw
erkg
ebru
ik m
et N
EN
is a
fges
lote
n.
Th
is d
ocu
men
t m
ay o
nly
be
use
d o
n a
sta
nd
-alo
ne
PC
. Use
in a
net
wo
rk is
on
ly p
erm
itte
d w
hen
a su
pp
lem
enta
ry li
cen
se a
gre
emen
t fo
r u
s in
a n
etw
ork
wit
h N
EN
has
bee
n c
on
clu
ded
.
NEN-EN 1011-5
Als Nederlandse norm is aanvaard:
- EN 1011-5:2003,IDT
Normcommissie 341 008 "Lassen en verwante processen"
Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation.
Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute.
Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht.
Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven.
©2002 Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) 2 690 390, Fax (015) 2 690 190
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
NEN-EN 1011-5
Nederlands voorwoord
Voor de in deze norm vermelde normatieve verwijzingen bestaan in Nederland de volgende equivalenten: vermelde norm Nederlandse norm titel EN 1011-3 NEN-EN 1011-3 Lassen - Aanbevelingen voor het lassen van
metalen - Deel 3: Booglassen van corrosievaste staalsoorten (en)
EN 10088-1 NEN-EN 10088-1 Corrosievaste staalsoorten - Deel 1: Lijst van corrosievaste staalsoorten (en,nl)
prEN ISO 5817:2002 NEN-EN-ISO 5817:2002 2e Ontw.
Lassen - Smeltlasverbindingen in staal, nikkel, titanium en hun legeringen (laserlassen uitgezonderd) - Kwaliteitsniveaus voor onvolkomendheden (en)
EN ISO 9692-4 - - EN ISO 13916 NEN-EN-ISO 13916 Lassen - Leidraad voor de meting van de
voorwarmtemperatuur, de tussenlaagtemperatuur en de handhaaftemperatuur (en)
prEN ISO 15607:2000 NEN-EN-ISO 15607:2000 Ontw.
Het beschrijven en kwalificeren van lasprocedures voor metallische materialen - Algemene regels (en)
prEN ISO 15609-1:2000
NEN-EN-ISO 15609-1:2000 Ontw.
Het beschrijven en kwalificeren van lasprocedures voor metallische materialen - Lasmethodebeschrijvingen - Deel 1: Booglassen (en)
prEN ISO 15614-1:2000
NEN-EN-ISO 15614-1:2000 Ontw.
Het beschrijven en kwalificeren van lasprocedures voor metallische materialen - Lasmethodebeproeving - Deel 1: Booglassen en autogeenlassen van staal en booglassen van nikkel en nikkellegeringen (en)
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
EN 1011-5
April 2003
ICS 25.160.10
English version
Welding - Recommendations for welding of metallic materials -Part 5: Welding of clad steel
Soudage - Recommendations pour le soudage desmatériaux métalliques - Partie 5: Soudage des aciers
plaqués
Schweißen - Empfehlungen zum Schweißen metallischerWerkstoffe - Teil 5: Schweißen von plattierten Stählen
This European Standard was approved by CEN on 28 February 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATIONC O M I T É E U R O P É E N D E N O R M A LI S A T I O NEUR OP ÄIS C HES KOM ITEE FÜR NOR M UNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.
Ref. No. EN 1011-5:2003 E
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
EN 1011-5:2003 (E)
2
Contents
page
Foreword ..................................................................................................................................................................... 3
1 Scope.............................................................................................................................................................. 4
2 Normative references ................................................................................................................................... 4
3 Terms and definitions................................................................................................................................... 5
4 Materials......................................................................................................................................................... 54.1 Clad steels ..................................................................................................................................................... 54.2 Parent metal................................................................................................................................................... 54.3 Cladding ......................................................................................................................................................... 5
5 Welding consumables for cladding deposits............................................................................................. 5
6 Welding procedures...................................................................................................................................... 6
7 Fabrication ..................................................................................................................................................... 6
8 Welding .......................................................................................................................................................... 78.1 Welding from both sides .............................................................................................................................. 78.2 Single side welding....................................................................................................................................... 78.3 General welding conditions ......................................................................................................................... 78.4 Welding procedure specification................................................................................................................. 8
9 Post-weld cleaning........................................................................................................................................ 9
10 Testing............................................................................................................................................................ 9
11 Correction of non-conformities ................................................................................................................... 9
Annex A (informative) Dilution rate......................................................................................................................... 10
Bibliography ............................................................................................................................................................. 11
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
NEN Standards Products & Servicest.a.v. afdeling KlantenserviceAntwoordnummer 102142600 WB Delft
Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via www.nen.nl/normshop
Gratis e-mailnieuwsbrievenWilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen,
normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze
e-mailnieuwsbrieven. www.nen.nl/nieuwsbrieven
Gegevens Bedrijf / Instelling
T.a.v. O M O V
Klantnummer NEN
Uw ordernummer BTW nummer
Postbus / Adres
Postcode Plaats
Telefoon Fax
Factuuradres (indien dit afwijkt van bovenstaand adres)
Postbus / Adres
Postcode Plaats
Datum Handtekening
NEN Standards Products & Services
Postbus 50592600 GB Delft
Vlinderweg 62623 AX Delft
T (015) 2 690 390F (015) 2 690 271
www.nen.nl/normshop
RetournerenFax: (015) 2 690 271
E-mail: [email protected]
Post: NEN Standards Products
& Services,
t.a.v. afdeling Klantenservice
Antwoordnummer 10214,
2600 WB Delft
(geen postzegel nodig).
Voorwaarden• De prijzen zijn geldig
tot 31 december 2016,
tenzij anders aangegeven.
• Alle prijzen zijn excl. btw,
verzend- en handelingskosten
en onder voorbehoud bij
o.m. ISO- en IEC-normen.
• Bestelt u via de normshop een
pdf, dan betaalt u geen
handeling en verzendkosten.
• Meer informatie: telefoon
(015) 2 690 391, dagelijks
van 8.30 tot 17.00 uur.
• Wijzigingen en typefouten
in teksten en prijsinformatie
voorbehouden.
• U kunt onze algemene
voorwaarden terugvinden op:
www.nen.nl/leveringsvoorwaarden.
preview - 2016
Bestelformulier
Normalisatie: de wereld op één lijn.
Stuur naar:
Ja, ik bestel
€ 50.04__ ex. NEN-EN 1011-5:2003 en Lassen - Aanbevelingen voor lassen van
metalen - Deel 5: Lassen van geplateerd staal