ß Hommel Hercules Machinist’s Hammers DIN 1041 - pge.ro · ß Hommel Hercules Machinist’s...
Transcript of ß Hommel Hercules Machinist’s Hammers DIN 1041 - pge.ro · ß Hommel Hercules Machinist’s...
54.1ENG/OP
ß Hommel Hercules
Machinist’s Hammers DIN 1041
0TypeSmooth ground on all sides,black varnished, bright faces.Note:Nylon caps cat.-no. 54016.
54000TypeDouble curved hickoryhandle.
54002TypeDouble curved ashwoodhandle.
54000
Machinist’s Hammers (DIN 1041)
4TypeHammer head in compliancewith DIN 1041.Drop forged steel, accurateground, hardened and tem-pered, both faces smoothground. Double curvedhickory handle. QualitySteel C 45 in compliancewith DIN 17200.
Note:Nylon caps cat.-no. 54016.
54003TypeWithout impact protectionsleeve.
54005TypeWith nickel-plated impactprotection sleeve, pressedinto the hammer head.
54007Model INDUTypeWith impact protection onboth sides by means of elec-tro-inductively tempering,non-slip hickory handle andnickel-plated impact pro-tection sleeve.
e 54003
e 54009
Impact protection sleeve INDUWeight Handle length 54003 … 54005 … 54007 …
w/o handle g approx. mm100 260 101200 280 102300 300 103 103 103400 310 104500 320 105 105 105600 330 106800 350 107 107 107
1000 360 108 108 1081500 370 109 109 1092000 400 110 110 110
54007
Hickory handle Ashwood handleWeight Handle length 54000 … 54002 …
w/o handle g approx. mm200 280 102 102300 300 103 103500 320 105 105800 350 107 107
1000 360 108 1081500 380 109 1092000 400 110 110
Machinist’s Hammers DIN 1041
4TypeSmooth ground on all sides,black varnished, bright faces.Note:Nylon caps cat.-no. 54016.
54009TypeWith unbreakable ULTRAMID plastic handle,safety wedge, therefore ham-mer head does not loosen.
54015TypeWith ULTRATEC three-com-ponent glass-fibre handle, un-breakable glass-fibre core.Handle permanently bondedto hammer head. Non-slipelastomer handle coating.Base coating made ofpolypropylene.
54015ULTRAMID ULTRATECWeight Handle length 54009 … 54015 …
w/o handle g approx. mm200 280 101 101300 300 102 102500 320 103 103800 350 104 104
1000 360 105 105
High-quality steel C 45
Ring wedge forsecure seat Hardened
and temperedon all sides(50-58 HRC)
Following theregulations,edges round-ed on all sidesHardness
in eyeletarea max.30 HRC
Double curvedhickory handle
DIN-eyelet withpressed-in steelsleeve for prevent-ing handle break-age at failed im-pacts.
54000 - 54002
54003 - 54007
54009 - 54015
54.2 ENG/OP
H a n d T o o l s
55
e 54065
Sledge Hammers
TypeBlack varnished, bright faces.
054048TypeDIN 6475. With curved ash-wood handle, ring wedge forsafe handle seat.
540534TypeWith ULTRATEC three-com-ponent glass-fibre handle, un-breakable glass-fibre core.Non-slip elastomer handlecoating. Base coating madeof polypropylene.
54053 101-104TypeDIN 6475. Handle permanent-ly bonded to hammer head.
54053 105-107TypeSecure seat thanks to conicalforce fit.
540554TypeDIN 6475. With steel pipehandle and plastic grip, blackvarnished.
0 4 4Weight Handle length 54048 … 54053 … 54055 …
w/o handle kg approx. mm1,00 250 101 101 1011,25 260 102 102 1021,50 270 103 1032,00 280 104 1043,00 900 1054,00 900 1065,00 900 107
4TypeDrop forged steel, accurateground, hardened and tem-
pered, both faces smoothground. Curved ashwoodhandle.
QualitySteel C 45 acc. to DIN17200.
Ashwood handle ULTRATECWeight Handle length 54065 … 54070 …
w/o handle kg approx. mm3 600 1024 600 1035 800 1046 800 1058 900 106
10 900 1073 900 1024 900 1035 900 104
Size Weight 54025 …Ömm w/o handle g
18 140 10120 190 10222 230 103
Size Weight 54025 …Ö mm w/o handle g
25 320 10428 450 10530 520 106
54065 - 54070
Carpenter’s Hammers DIN 510954025
Double-Face Blacksmith’s Hammers54048 - 54055
e 54055
e
54053 101-104
54048
e 54025
54053 105-107
54070
Nylon Caps
TypeMade of polyurethane.
ApplicationFor machinist’s hammers foruse as soft face hammers in
compliance with DIN 1041(cat.-no. 54000 - 54015).
For hammer- 54016 …weight g
300 101500 102
For hammer- 54016 …weight g
800 1031000 104
54016
54016
4TypeForged, hardened and tem-pered with care.QualitySteel C 45 acc. to DIN17200.
54065TypeDIN 1042. With straight ashwood handle.
54070TypeWith ULTRATEC three-com-ponent glass-fibre handle, un-breakable glass-fibre core.Secure seat thanks to conicalforce fit. Non-slip elastomerhandle coating. Base coatingmade of polypropylene.
e
54.3ENG/OP
ß Hommel Hercules
Ash wood Hickory woodFor Hammer- Handle- Handle- 54071 … 54073 …
weight g length mm end mm100 260 17/10 101 101200 280 19/11 102 102300 300 21/12 103 103400 310 24/14 110 110500 320 26/15 104 104
Ash wood Hickory woodFor Hammer- Handle- Handle- 54071 … 54073 …
weight g length mm end mm600 330 28/16 105 105800 350 29/17 106 106
1000 360 31/18 107 1071500 380 33/20 108 1082000 400 37/22 109 109
54073
54071TypeAshwood, straight, 1. Quality, DIN 5111.
54073TypeHickory, double curved, 1. Quality, DIN 5111.Note:Cat.-no. 54073 101 straightshape.
Spare Handles for Machinist’s Hammers54071 - 54073
54075TypeHickory, double curved,1. Quality.ApplicationFor hammers with impact pro-tection sleeve (cat.-no. 54005- 54007).
54076TypeHickory, double curved, 1. Quality, non-slip.ApplicationFor hammers with impact pro-tection sleeve (cat.-no. 54005- 54007).
54077TypeHigh-quality plastic ULTRAMID with safety wedgefor permanent, secure seat,complete with wedge and pin.ApplicationFor all hammers in compliancewith DIN 1041.
Spare Handles for Machinist’s Hammers
54077
54075
Hickory wood Hickory, non-slip ULTRAMIDfor Hammer- Handle length Handle- 54075 … 54076 … 54077 …
weight g approx. mm end mm200 280 19/11 102300 300 21/12 103 103 103
400/500 320 26/15 104 104 104800 350 29/17 106 106 106
1000 360 31/18 107 107 1071500 380 33/20 108 1082000 400 37/22 109 109
Spare Handles for Sledge Hammers
54081TypeAshwood, straight, 1. Quality, DIN 5112.Note:Cat.-no. 54081 101 curvedshape.
54083TypeHickory, straight, 1. Quality, DIN 5112.
54081
Ash wood Hickory woodFor Hammer- Handle length Handle- 54081 … 54083 …
weight kg approx. mm end mm3 - 4 600 42/24 101 1015 - 6 800 48/48 102 102
8 - 10 900 52/32 103 103
Spare Handles for Double-Face Blacksmith’s Hammers
54087TypeAshwood, curved, 1. Quality, DIN 5135.
54089TypeHickory, curved, 1. Quality, DIN 5135.
54087
54089Ash wood Hickory woodFor double-face blacksmith’s Handle length Handle- 54087 … 54089 …
hammer-weight kg approx. mm end mm1 - 1,25 260 31/18 101 101
1,5 280 33/20 102 1022 300 37/22 103 103
54071
54083
54075 - 54077
54081 - 54083
54087 - 54089
54.4 ENG/OP
H a n d T o o l s
55
Light Metal Hammers
TypeCylindrical, with doublecurved hickory handle.
ApplicationFor hammering out dents andstraightening workpieces.
Striking face Head length Weight 54104 …Ø mm approx. mm approx. g
40 75 250 20140 105 350 20250 92 500 203
Striking face Head length Weight 54104 …Ø mm approx. mm approx. g
60 98 750 20460 128 1000 205
Safety Handle Wedges (S-FIX Claw Wedges)
TypeFor permanent connection be-tween tool and handle. Applywedge diagonally and newlydesigned wedge jaws provide
higher expansion. designedwedge jaws.
Width For Hammer- 54095 …Size mm weight approx. g
00 13 100 - 200 2010 16 250 - 400 2021 20 500 - 800 2032 23 1000 - 1500 2043 26 1750 - 2000 2054 29 3000 - 5000 2065 32 axes, hatchets 207
5.1/2 40 axes, hatchets 2086 50 axes, hatchets 209
54095
Copper Hammers
54118Type Similar to DIN 5130.Made of drawn copper rods,square type. Brinell hardness 60-80. With doubly curved, waxedashwood handle.
54120 TypeDIN 5130. Made of drawn copper rods,square type, fully ground.Brinell hardness 80-110. With doubly curved, waxedashwood handle.
Weight 54118 … 54120 …approx. g
250 200500 201750 202
1000 2031500 204
Weight 54118 … 54120 …approx. g
2000 2052500 2063000 2074000 2085000 209
Mallets DIN 7462/B
TypeCommon beechwood, withpressed-on metal sheath andoval ashwood handle.
Head Ø x Weight 54130 …Head length mm approx. g
50 x 100 220 10160 x 120 370 10270 x 140 560 103
Head Ø x Weight 54130 …Head length mm approx. g
80 x 160 810 10490 x 180 1100 105
54095
54104
54118 - 54120
54130
54104
54130
54118 - 54120
54.5ENG/OP
ß Hommel Hercules
Composition Rubber Mallets DIN 5128-90
54150TypeWith two flat faces and ashwood handle, approx. 95Shore-hardness, strong im-pact but low rebound.
54151Spare handles
54150
Hammer Spare handleHead Ø x Handle length Weight with 54150 … 54151 …
Size DIN Head length mm approx. mm handle approx. g0 A 100 40 x 80 260 160 101 1011 A 200 54 x 90 320 300 102 1022 A 400 64 x 113 340 500 103 1033 A 600 74 x 127 360 700 104 1044 A 900 90 x 139 380 1150 105 105
Recoilless Soft-Face Hammers
dSupercraftTypeExchangeable hammer heads.Note:Double-impact effect, whichtransmits almost 100 % of theimpact load to the workpiece(compared with about 55 %with conventional hammers).Rebound delay through loosesteel shot filling in hammerhead.
54153TypeWith nylon-heads and hickory handle.
54154TypeWith nylon heads and steelpipe handle with rubber grip.
54155TypeWith nylon heads andULTRATEC three-componentglass-fibre handle, unbreak-able glass-fibre core. Handlepermanently bonded to ham-mer head. Non-slip elastomerhandle coating. Base coatingmade of polypropylene.
54156Spare nylon-heads
54158Spare hickory handles
54154
Hickory handle Steel pipe handle ULTRATEC Nylon heads Spare handleØ of head x Total length Weight approx. g cat.-no. 54153 … 54154 … 54155 … 54156 … 54158 …
Head length mm approx. mm 54153 54154 5415525 x 105 305 280 370 – 101 101 101 10130 x 110 330 400 520 – 102 102 102 10235 x 110 340 550 650 – 103 103 103 10240 x 115 360 700 820 780 104 104 204 104 10350 x 120 370 1000 1140 1090 105 105 205 105 10360 x 145 370 1650 1770 1660 106 106 206 106 10480 x 200 880 4000 – – 107 107 105
100 x 210 1000 7000 – – 108 108 106
54156
54158
54150 - 54151
54153 - 54158
54155
e 54153
54152 Special Bumping Mallets
hType Permanent-ductile filling ma-terial for workpiece-friendlyhammering.
54152 101TypeHandle adjustable by 90°.
Rubber Total 54152 …body mm length mm
70 x 70 260 10070 x 140 280 101
54152 100
54152 101
54.6 ENG/OP
H a n d T o o l s
55
Plastic Hammers
54172TypeMiddle part made of grey castiron, exchangeable heads andwooden handle.
54172 100-105Heads made of impact-proof plastics, red, transpar-ent.
54172 106Heads made of nylon, white.
54173Spare headsPairs.
54172 100-105
54172 106
Hammer Spare heads (pair)Heads Head Ø Handle length Weight 54172 … 54173 …
made of mm approx. mm approx. gplastics 22 252 140 100 100plastics 27 265 215 101 101plastics 32 280 310 102 102plastics 35 298 395 105 105plastics 40 320 530 103 103plastics 50 340 800 104 104
nylon 50 340 800 106 106
Plastic Hammers
LTypeCentre piece made of mal-leable cast iron, with impact-proof, exchangeable impactheads (rounded faces), hard-wood handles. Resistantagainst almost all mineral oil,fats and solvents.
54175TypeHeads blue.ApplicationFor standard duty.
54176TypeHeads yellow, particularlyductile and wear-resistant.ApplicationFor very heavy duty (hammerfaces will not crack).
54177Loose HeadsBlue, 2 rounded faces, in pairs.
54179Loose HeadsYellow, 2 rounded faces, in pairs.
Blue Yellow S.-Head blue S.-Head yellowHead Ø x Total length Weight 54175 … 54176 … 54177 … 54179 …
Head length mm approx. mm approx. g22 x 80 260 160 101 101 101 10127 x 90 280 230 102 102 102 10232 x 100 300 325 103 103 103 10335 x 106 320 415 104 104 104 10440 x 112 340 570 105 105 105 10550 x 120 360 920 106 106 106 10660 x 125 380 1280 107 107 107 107
Recoilless Soft-Face Hammer
dSECURALTypeSpecial ergonomic designed
metal hammer housing withrubber handle. Heads madeof polyurethane, exchange-able, size 30 x 40 mm.
ApplicationFor multi-purpose use withhigh security standard.
54165 102
Size Weight 54165 …mm approx. g
Soft face hammer 40 700 101Space-heads (pair) 30 x 40 – 102
54165 101
54165
54172 - 54173
54175 - 54179
54176
54175
Recoilless Soft-Face Hammers
4TypeHammer head made of metal,with steel shot filling, com-pletely plastic-coated, particu-
larly impact-resistant due to aspecial plastic composition.Temperature resistant from -20° to +90°C.
ApplicationFor save treatment of work-pieces.
54161
Head Ø Weight 54161 …mm approx. g
30 270 10135 385 10245 620 103
Head Ø Weight 54161 …mm approx. g
50 860 10460 1340 105
54161
54173 100-105 54173 106
54.7ENG/OP
ß Hommel Hercules
54193
54190
Simplex Soft-Face Hammers
54192
dType5 sizes and 6 impact tipswith different hardnesses (seecat.-no. 54190 - 54195).Therefore, the Simplex-softface hammer is suitable formany applications. Clampwith one screw! No wedging!All heads in the same size canbe combined at will.
54183TypeComplete with two-partclamping housing made ofmalleable cast iron, Sim-plex-handle and compositionrubber impact heads.
54184TypeComplete with two-part clamp-ing housing made of malleablecast iron, Simplex-handle andplastic impact heads.
54186Clamping housing made ofmalleable cast iron, single,two-part with clamping screws.
54188Spare handles, hardwood.
54194
e 54183
54195
Composition rubber Plastics Housing Spare handleImpact tip- Head length Hammer length Weight 54183 … 54184 … 54186 … 54188 …
Ø mm mm mm approx. g30 90 300 350 101 101 301 10140 110 330 655 102 102 302 10250 135 350 1130 103 103 303 10360 145 405 1610 104 104 304 10480 175 490 3150 105 305 105
Impact Tips for Simplex Soft-Face Hammers
d54190TypeTPE-soft, blue, soft impact,colour proofed. Shore-hard-ness approx. 95 A.ApplicationSensitive surfaces, e.g. as-sembly, furniture industry, lay-ing tile, etc.
54191TypeComposition rubber, black,medium impact, Shore-hard-ness approx. 95 A, specialrubber composition.ApplicationUniversal use.
54192TypePlastics, red, hard impact,transparent plastics, fat- andoil-resistant.ApplicationUniversal use.
54193TypeSuperplastics, white, veryductile and unbreakable plas-tics, resistant against fats,oils, acid and alkalines.ApplicationEspecially suitable for edgeimpacts.
54194TypeNylon, white, hardest impact,high impact efficiency thanksto high elasticity, resistantagainst fats and oils.ApplicationFor strong adjustment im-pacts.
54195TypeSoft metal, silver, very highimpact, light-metal special al-loy, heat-resistant.ApplicationReplaces standard lead ham-mers.
54191
TPE-soft Comp. rubber Plastics Superplastics Nylon Soft metalTip Ø 54190 … 54191 … 54192 … 54193 … 54194 … 54195 …
mm30 101 101 101 101 101 10140 102 102 102 102 102 10250 103 103 103 103 103 10360 104 104 104 104 104 10480 105 105 105 105
54188
54183 - 54188
54190 - 54195
54184
54186
54.8 ENG/OP
H a n d T o o l s
55
e 54200
e 54204
Carpenter’s Roofing Hammers DIN 7239
e 54203
4TypeWith ground nail claw andpointed face, rough impactface, nail holder, steel pipe
handle and steel ring for im-proved handle protection,plastic handle, black lac-quered, head protection.
e 54202
Weight Magnetic 54200 …approx. g nail holder
600 – 101600 x 102
Plasterer Hatchet
4TypeWith steel pipe handle andplastic grip, black varnished,polished edge, roughened im-pact face.
Weight 54204 …approx. g
700 101
Masonry Hammer
4TypeBerlin form, with steel pipehandle and plastic handle,black lacquered, smooth im-pact face.
Weight 54202 …approx. g
750 101
Masonry Hammer
4TypeShape: Rheinisch. With steelpipe handle and plastic grip,black varnished.
Weight 54203 …approx. g
600 101
54200
54202
54203
54204
54197 FERROPLEX Hammers
dType 2 in 1: Machinist’s hammerand soft face hammer. Ham-mer heads: tempered steelimpact head and exchange-
able nylon impact head. Steelpipe handle permanentlybonded to hammer head. Quality Impact face hardened andtempered.
Note:Spare nylon heads see cat.-no. 54156 102 + 103.
Head Ø x Total Length Weight 54197 …Head length mm approx. mm approx. g
30 x 104 290 600 10135 x 104 295 800 102
54197
54.9ENG/OP
ß Hommel Hercules
Set 54295 …Contents
6-part 101
Centre Punch and Drift Punch Set
ßTypeOctagonal, shank lacquered, safety zone especially electro-inductive hardened.
6-part: 1 Centre punch DIN 7250,
120 x 10 x 4 mm,5 drift punches DIN 6458,
120 x 10 x 2 - 6 mm, (dimensions = overall lengthx shank Ø x end of taper Ø), in sheet metal box.
QualityChrome-vanadium air-hard-ened steel.
e 54295
54295
54297 Impact Tool Assortment
VType 19-part, in plastic case.Sheathed, low-vibration andimpact-dampening comforthandle with exchangeableinserts made of 3 differentmaterials: brass, polyamide,aluminium. The insert-systemallows for an efficient choiceof the hardness, in order toprevent workpiece damage.Mounting by means of M10thread. The insert ring damp-ens the impacts, the threadwill not be damaged.
Application For working on all types of ax-es, shafts, pins, bearings.Perfect for Cardan shafts,gearings. For removing, re-placing and tightening ofworkpieces: Brass inserts: Hardness HV.155 (430-500N/mm2), Polyamide inserts: Shore-hardness 85D, Aluminium inserts: 370 N/mm2.
Set contents: 1 comfort handle, 3 brass inserts Ø 12 / 16 / 20 mm, usable length 40 mm, 3 polyamide inserts Ø 12 / 16 / 20 mm, usable length 40 mm, 5 aluminium inserts Ø 10 / 12 / 14 / 16 / 18 mm, usable length 60 mm, 1 extension, usable length 100 mm, 3 brass inserts for extension pieces Ø 12 / 16 / 18 mm, usable length 20 mm, 3 polyamide inserts for extension pieces Ø 12 / 16 / 18 mm, usable length 20 mm,
Set 54297 …Contents
19-part 101
54297
Centre Punch
ßTypeKnurled shank.QualityHardened steel.
54300
Total Shank Ø 54300 …length mm mm
100 8 101
54300
ßTypeHexagonal end, with carbide pointed tip, regrindable.
54303
Total Shank Ø 54303 …length mm mm
120 12 101
Centre Punch with Carbide Tip54303
54.10 ENG/OP
H a n d T o o l s
55
e 54305
Centre Punches
VTypeHexagonal, shank lacquered,tip polished and hardened to58 HRc.
QualityHighly resistant special steel.
Total Shank Ø End of taper Ø 54307 …length mm mm mm
100 8 2 101120 8 3 102130 10 4 103
Total Shank Ø End of taper Ø 54307 …length mm mm mm
150 10 6 104150 12 8 105
Centre Punches DIN 7250
54305ßTypeOctagonal, forged, impacthead tempered, shank lac-quered, safety zone thanks toelectro-inductive special hard-ening procedure.
QualityChrome-vanadium air-hard-ened steel.
54306L
TypeOctagonal, glossy nickel-plat-ed, with plastic hand guard.
QualityVanadium-extra-steel.
54306
Centre Punches with Handle
VTypeDamping handle, very goodgrip, ergonomic, with fingerguard, temperature-resistant.
The head is hardened to 43HRc, to prevent chipping. Tiphardness 58 HRc. Grip com-fort and vibration characteris-tic ensures high precision andstrong impact.
Total Shank Ø End of taper Ø 54309 …length mm mm mm
185 10 2,5 101185 10 4,0 102185 10 6,0 103
Total Shank Ø End of taper Ø 54309 …length mm mm mm
185 12 8,0 104185 14 10,0 105
ß L
Total Shank Ø End of taper Ø 54305 … 54306 …length mm mm mm
100 8 3 101120 10 4 201 102120 12 5 202150 12 5 203 103
54307
54309
54305 - 54306
54307
54309
Spring-Loaded Centre Punch
ApplicationCan be used on both sides.Impact force is generated by a
built-in spring. Hammers orother tools are not necessary. 54318
54318 …
101
Automatic Centre Punch
54314TypeWith spring mechanism, tipsexchangeable, adjustable im-pact.
ApplicationFor single-hand operation.QualitySpecial steel.
54315Spare tip.
Centre punch Spare punch pointTotal Shank Ø 54314 … 54315 …
length mm mm130 17 201 201
54314 - 54315
54318
54314
54315
54.11ENG/OP
ß Hommel Hercules
Drift Punches DIN 6458
ßTypeOctagonal, forged, temperedimpact head, varnishedshank. Safety zone thanks toelectro-inductive special hard-ening process.
ApplicationFor driving out rivets, bolts,etc.QualityChrome-vanadium air-hard-ened steel.
e 54321
54323
End of taper Ø Shank Ø Total 54321 …mm mm length mm
1 10 120 2012 10 120 2023 10 120 2034 10 120 2045 12 120 2056 12 120 206
End of taper Ø Shank Ø Total 54321 …mm mm length mm
7 12 120 2078 12 120 208
10 14 150 20912 14 150 21015 18 175 211
Set singlefor borehole Ø 54319 … 54320 …
mmSet 6 - 16 101
6 - 8 1018 - 11 102
11 - 16 103
Adjustable Centre Punches
54319
54319 - 54320
54321
TypeThe punch consists of punch-ing pin, guide bush and cen-tring sleeve. Application For transmitting of existingboreholes to other work-pieces.
Application 1. Insert punch into borehole. 2. Extent the centring flaps
until they completely touchthe borehole.
3. Hit the pin with the hammer.
54319 3-part set in plastic box.
Centre Drift Punches
ßTypeKnurled shank. Zinc chrome-plated.
54323
End of taper Ø Shank Ø Total 54323 …mm mm length mm
1 6 100 1012 6 105 1023 8 110 1034 8 115 1045 8 120 1056 10 125 1067 10 130 1078 12 135 1089 12 140 109
Drift Punches With Handle
VTypeVibration damp handle, goodgrip and ergonomic designed,
with finger guard, not affectedby . Hardened head of 43HRc, to avoid cracking. Tiphardness 58 HRc. High grip-
ping comfort and damping,therefore high precision andhigher impact force.
End of taper Ø Shank Ø Total 54324 …mm mm length mm1,9 10 185 1012,9 10 185 1023,9 10 185 1034,9 10 185 1045,9 10 185 1057,8 12 185 106
54324
54324
54.12 ENG/OP
H a n d T o o l s
55
Drive Pin Punches with Handle
VTypeVibration damp handle, goodgrip and ergonomic designed,with finger guard, not affectedby changes in temperature.
Hardened head to 43 HRc, toavoid cracking. Tip hardness58 HRc. Grip comfort and vi-bration characteristic ensureshigh precision and strong im-pact.
SetSet Pin Ø 54351 …
contents mm5-part 2,9 / 3,9 / 4,9 / 5,9 / 7,9 1017-part 1,9 / 2,9 / 3,9 / 4,9 / 5,9 / 7,9 / 9,8 102
singlePin Ø Shank Ø Total 54352 …
mm mm length mm1,9 10 175 1012,9 10 190 1023,9 10 195 1034,9 10 205 104
Pin Ø Shank Ø Total 54352 …mm mm length mm5,9 12 210 1057,9 12 220 1069,8 14 230 107
54351
54351 - 54352
Drift Punches DIN 6458
LTypeOctagonal, with plastic handguard.
ApplicationFor driving out rivets, bolts,etc.
QualityVanadium-extra steel, nick-el-plated.
54327
End of taper Ø Shank Ø Total 54327 …mm mm length mm
2 10 120 1013 10 125 1024 10 130 103
End of taper Ø Shank Ø Total 54327 …mm mm length mm
5 10 165 1056 10 180 1068 12 200 107
54327
Drive Pin Punch Set DIN 6450 C
ßType6-part:3 / 4 / 5 / 6 / 7 / 8 mm tip Ø,length 150 mm, octagonal,impact head tempered, shankgold-varnished, in sheet met-al box.
QualityChrome-vanadium air-hard-ened steel, forged.
Set 54349 …Contents
6-part 101
Drive Pin Punch Set
hType6-part:2 / 3 / 4 / 5 / 6 / 8 mm tip Ø,length 150 mm, Octagonal,matt-black, in plastic stand.
QualityChrome-vanadium air-hard-ened.
Set 54350 …Contents
6-part 101
54350
54349
54350
54349e
54.13ENG/OP
ß Hommel Hercules
Set of Drive Pin Punches With Guide Sleeve
ßType8-part:0,9 / 1,4 / 1,8 / 2,4 / 2,8 / 3,4 /3,9 / 5,9 mm tip Ø, withknurled, nickel-plated guidebushings, in sheet metalbox.
ApplicationLocate the point with thesleeve in a fully forward posi-tion. During drifting the sleeveslides back thus continuing tosupport the punch point.
QualityChrome-vanadium steel,highly polished.
Note:Pin Ø 5,9 mm without guidesleeve.
54359
Set 54359 …Contents
8-part 101
Set of Drive Pin Punches With Guide Sleeve
LType8-part:0,9 / 1,4 / 1,8 / 2,4 / 2,8 / 3,4 /3,9 / 5,9 mm tip Ø, drivingpoints finely ground and pol-ished, with knurled, nickel-plated guide bushings, inplastic stand.
ApplicationLocate the point with thesleeve in a fully forward posi-tion. During drifting the sleeveslides back thus continuing tosupport the punch point.
QualityVanadium-extra steel, nick-el-plated and chrome-plat-ed.
Note:Pin Ø 5,9 mm withoutguide sleeve.
54364
Set 54364 …Contents
8-part 101
Drive Pin Punch Set DIN 6450 D
LType6-part:2 / 3 / 4 / 5 / 6 / 8 mm tip Ø,octagonal, driving points finelyground and polished, withplastic hand guard, in wooden stand.
QualityVanadium-extra steel,nickel-plated. 54369
Set 54369 …Contents
6-part 101
54359
54364
54369
54380 Drive Pin Punches DIN 6450 C
ßTypeOctagonal, tempered impacthead, gold-varnished shank.
QualityChrome-vanadium air-hard-ened steel, forged. e 54380
Pin Ø Shank Ø Total 54380 …mm mm length mm
2 10 150 1013 10 150 1024 10 150 1035 10 150 1046 10 150 105
Pin Ø Shank Ø Total 54380 …mm mm length mm
7 12 150 1068 12 150 107
10 12 150 10812 14 150 109
54.14 ENG/OP
H a n d T o o l s
55
Tool Set
ßTypeSafety zone thanks to electro-inductive special hardeningprocess. Impact head, tem-pered.
6-part:1 ea. flat chisel 125 and150 mm,1 cape chisel 125 mm,1 centre punch 120 mm,1 ea. drift punches 2 and3 mm, in sheet metal box.
QualityChrome-vanadium air-hard-ened steel, forged.
e 54592
Set 54592 …Contents
6-part 101
54592
Drive Pin Punches
ßTypeKnurled shank.
Zinc chrome-plated.
54382
Drive Pin Punches DIN 6450 D
LTypeOctagonal, driving points fine-ly ground and polished, withplastic hand guard.
QualityVanadium-extra steel, nickel-plated.
Pin Ø Shank Ø Total 54383 …mm mm length mm
2 8 115 1013 8 125 1024 10 150 1035 10 165 1046 12 180 1058 12 200 106
Pin Ø Shank Ø Total 54382 …mm mm length mm
1 6 100 1012 6 105 1023 8 110 1034 8 115 1045 8 120 1056 10 125 1067 10 130 1078 12 135 1089 12 140 109
54383
54383
54382
Drive Pin Punches
TypeWith knurled and nickel-platedguide sleeve.ApplicationLocate the point with thesleeve in a fully forward posi-tion. During drifting the sleeveslides back thus continuing tosupport the punch point.
Note:Tip Ø 5,9 mm without guidebushings.
54385ßQualityChrome-vanadium steel,highly polished.
54390®QualityVanadium-extra steel,nickel-plated and chrome-plated.
54390
ß ®Pin Ø Total length 54385 … 54390 …
mm approx. mm0,9 75 101 1011,4 85 102 1021,8 85 103 1032,4 90 104 104
ß ®Pin Ø Total length 54385 … 54390 …
mm approx. mm2,8 95 105 1053,4 95 106 1063,9 100 107 1075,9 100 108 108
54385 - 54390
54.15ENG/OP
ß Hommel Hercules
Flat Chisels DIN 6453
ß TypeFlat-oval body, forged, var-nished shank, fully regrind-able cutting edge, strikingface tempered.
Safety zone thanks to electro-inductive special hardeningprocess.Cutting edge ground and var-nished.
QualityChrome-vanadium air-hard-ened steel.
e 54601
Total Body Cutting 54601 …length mm length mm length mm
100 14 x 9 15 101125 14 x 9 18 102150 17 x 11 18 103175 20 x 12 21 104200 23 x 13 24 105250 23 x 13 25 106300 23 x 13 26 107
Cape Chisels DIN 6451
ß TypeFlat-oval body, forged, var-nished shank, fully regrind-able cutting edge, strikingface tempered. Safety zone thanks to electro-inductive special hardeningprocess. Cutting edge groundand varnished.
QualityChrome-vanadium air-hard-ened steel.
Total Body Cutting 54605 …length mm length mm length mm
125 14 x 9 5,5 102150 17 x 11 6,0 103175 17 x 11 7,0 104200 20 x 12 8,0 105250 23 x 13 9,0 106300 23 x 13 9,0 107
54601
54605
e 54605
Grooving Chisels DIN 6455
ß TypeOctagonal, tempered impacthead, varnished shank.
QualityChrome-vanadium air-hard-ened steel.
Cutting Length x Shank 54620 …width mm thickness mm
3 150 x 10 1024 150 x 10 1035 150 x 10 104
5462054620
Web Chisels
ß TypeTwo cutting edges with all-round free angle. Octagonal,varnished shank, striking facetempered.ApplicationFor removing webs betweendrill holes.
QualityChrome-vanadium air-hard-ened steel.
Note:The shape of the double cut-ting edge prevents deforma-tion or upsetting on the work-piece.
54622
Cutting edge Total Body 54622 …W x L mm length mm height mm
2 x 10 125 10 1013 x 10 125 10 1024 x 12 150 12 1035 x 12 150 12 104
54622
54.16 ENG/OP
H a n d T o o l s
55
Stone Chisels DIN 7254
ßTypeOctagonal, forged, impacthead tempered, shaft gold-lacquered, cutting edgeground and lacquered.
QualityChrome-vanadium air-hard-ened steel.
e 54656
Length Cutting 54656 …mm width mm200 23 101250 23 102300 26 103400 30 104500 30 105
54656
Slotting Chisel
ßTypeForged, striking face tem-pered, gold colour varnishedshank, cutting edge groundand varnished.ApplicationFor metal- and masonry work.
QualityChrome-vanadium air-hard-ened steel.
e 54624
Length Cutting 54624 …mm width mm240 26 x 7 102
Electrician’s Slotting Chisel
ßTypeWith hand guard, 2 cuttingedges, forged, impact headtempered, gold-lacquered,cutting edge ground and lac-quered.
QualityChrome-vanadium air-hard-ened steel.
Length Cutting 54625 …mm width mm250 34 202
Moil Point Chisels DIN 7256
ßTypeOctagonal, forged, impacthead tempered, shaft gold-lacquered, cutting edgeground and lacquered.
QualityChrome-vanadium air-hard-ened steel.
Length Ø 54650 …mm mm200 16 101250 16 102300 18 103400 20 104500 20 105
54624
54625
54650
e 54650
e54625
54.17ENG/OP
ß Hommel Hercules
Rivet Head Formers DIN 6435
54814 105TypeOctagonal, with safety strikingface.Set in plastic box.
QualityChrome-vanadium air-hard-ened steel.
Fits rivet 54814 …shank Ø mm
2 1013 1024 1035 104
Set 5-part 2 / 3 / 4 / 5 / 6 105
Electrician’s Stone Chisels
ß TypeForged, impact head tem-pered, shaft gold-lacquered,cutting edge ground and lac-quered.
QualityChrome-vanadium air-hard-ened steel. e 54665
Length Cutting Body 54665 …mm width mm thickness mm200 10 8 201200 12 10 202250 10 8 203250 12 10 204300 14 12 205
Fits rivet 54812 …shank Ø mm
2 1013 1024 1035 104
Set 5-part 2 / 3 / 4 / 5 / 6 105
Rivet Set DIN 6434
TypeOctagonal, with safety strikingface.Set in plastic box.
QualityChrome-vanadium air-hard-ened steel.
54812 105
Chisel Hand Guard
ß ApplicationUniversal use, for flat-oval 20 x 12 mm and
26 x 13 mm, and for octagonal16 -18 mm.
e 54680
Total 54680 …length mm
110 101
54665
54680
54812
54814
Blind Rivet Assortment
aTypeContents:1 Hand riveter model NTX(cat.-no. 54825) and 12 blindrivet sizes, 3 mm and
4 mm Ø made of different ma-terial, in sheet metal case.
54820
54820 …
101
54820
54.18 ENG/OP
H a n d T o o l s
55Mechanical Hand Riveters
aNote:Spare nosepieces availableon request.
54825Model NTXTypeNarrow riveter head, goodleverage ratio, with 3 nose-pieces size 3,2 / 4,0 / 5,0 mmand fitting wrench.
ApplicationFor aluminium alloy rivets upto 5 mm Ø and stainless steelrivets up to 4 mm Ø.QualityChrome-vanadium steelhandles. Housing made ofpressure die-cast alumini-um.
54827Model HN 2TypeNo force transmission ontothe workpiece surface, with 5 nosepieces size 4,0 / 4,8 /5,0 / 6,0 / 6,4 mm.ApplicationFor all materials up to 6,4 mm rivet Ø.QualityHousing made of pressuredie-cast aluminium.
NTX HN 2For rivet Ø Length 54825 … 54827 …
mm mm3,2 - 5,0 260 1014,0 - 6,4 570 201
Hand Riveter
54825
aFLIPPER
TypeReal single-hand use, by 40%reduced expenditure of force.With mandrel drop-in box.
ApplicationFor aluminium rivets up to 5 mm Ø and stainless steelrivets up to 4 mm Ø. Single lift of stroke 1,8 mm. 54824
For rivet Ø Weight 54824 …up to mm kg
5 0,75 101
Mechanical Hand Riveters
54827
ß TypeWith opening spring, 4 nose-pieces size 2,4 3,2 / 4,0 / 4,8 mm and fitting wrench.
54821TypeWith narrow riveter head.
54823TypeRiveter head swivelsthrough 360°.ApplicationEasy and quick adjustment inany angle position, thereforemost suitable also at difficultto reach spots.
For rivet Ø Length 54821 … 54823 …mm mm
2,4 - 4,8 260 1012,4 - 4,8 300 101
54821
Air-Hydraulic Blind Rivet Gun
aModel PH 2
TypeWith relieve valve, operatingpressure 6 bar, hose coupling6 mm Ø (1/4 inch).
ApplicationFor all materials up to 5 mm rivet Ø.Note:Spare nosepieces availableon request.
54823
54828
Air consumption per Rivet set Tensile force Length 54828 …rivet set ltr. per min. kp mm
1,2 - 1,8 25 - 30 900 330 101
54821 - 54823
54824
54825 - 54827
54828
▼
▼
54.19ENG/OP
ß Hommel Hercules
54832
Blind Riveting Tool AccuBird
Steel Blind Rivets with Mushroom Head DIN 7337
aTypeElectro-mechanic blind riveter,12 Volt, 1 incl. quick-changeakku. 1 quick charger, incase.ApplicationFor blind rivets up to 5 mm Ø
of all materials and BULB-TITE-rivets 4, 5,2 and 6,3 mmØ aluminium and steel.Technical specifications:Stroke: 20 mm,Tensile strength: 8.500 N,Weight: 2,2 kg with rechar-
geable battery.
Aluminium Blind Rivets with Mushroom Head DIN 7337
a TypeHollow rivet: Steel galvanized,mandrel: Galvanised steel.Pack = 500 pcs.
54829 …
AccuBird 201Quick-exchange rechargeable battery 202
a TypeHollow rivet: aluminium alloy, mandrel: galvanised steel,melting point approx. 600 °C.
54830
54829 202
Rivet Ø x Clamp Drill Ø mm/ 54832 …Shaft length mm length mm shear strength kp
3 x 5 0,5 - 2,0 3,1 / 112 1013 x 6 2,0 - 3,0 3,1 / 112 103
3 x 10 5,0 - 6,5 3,1 / 112 105
Rivet Ø x Clamp Drill Ø mm/ 54832 …Shaft length mm length mm shear strength kp
4 x 8 2,5 - 4,5 4,1 / 204 1134 x 10 4,5 - 6,5 4,1 / 204 1144 x 12 6,5 - 8,5 4,1 / 204 115
Rivet Ø x Clamp Drill Ø mm/ Pack = 54830 …Shaft length mm length mm shear strength kp pcs.
2,4 x 4 0,5 - 1,5 2,5 / 35 1000 1013,0 x 4 0,5 - 1,5 3,1 / 71 500 1043,0 x 5 1,5 - 2,5 3,1 / 71 500 1053,0 x 6 2,5 - 3,5 3,1 / 71 500 1063,0 x 8 4,5 - 5,0 3,1 / 71 500 108
3,0 x 10 5,0 - 7,0 3,1 / 71 500 1093,0 x 12 7,0 - 9 0 3,1 / 71 500 1104,0 x 6 1,5 - 3,0 4,1 / 143 500 1184,0 x 8 4,0 - 5,0 4,1 / 143 500 120
Rivet Ø x Clamp Drill Ø mm/ Pack = 54830 …Shaft length mm length mm shear strength kp pcs.
4,0 x 10 5,0 - 6,5 4,1 / 143 500 1214,0 x 12 6,5 - 8,5 4,1 / 143 500 1224,0 x 16 10,5 - 12,5 4,1 / 87 500 1235,0 x 8 2,5 - 4,5 5,1 / 204 500 127
5,0 x 10 4,5 - 6,0 5,1 / 204 500 1285,0 x 12 6,0 - 8,0 5,1 / 204 500 1295,0 x 16 12,0 5,1 / 204 500 1316,0 x 12 5,0 - 7,0 6,1 / 316 250 237
Aluminium Blind Rivets with Mushroom Head DIN 7337
a TypeHollow rivet: aluminium alloy,mandrel: Stainless steel.Pack = 500 pcs.
54831
Rivet Ø x Clamp Drill Ø mm/ 54831 …Shaft length mm length mm shear strength kp
3 x 6 1,5 - 3,5 3,1 / 71 1023 x 8 3,5 - 5,0 3,1 / 71 105
3 x 10 5,0 - 7,0 3,1 / 71 106
Rivet Ø x Clamp Drill Ø mm/ 54831 …Shaft length mm length mm shear strength kp
4 x 6 1,5 - 3,0 4,1 / 143 1124 x 8 3,0 - 5,0 4,1 / 143 114
4 x 10 5,0 - 6,5 4,1 / 143 115
54832
Stainless Steel Blind Rivets with Mushroom Head DIN 7337
a TypeHollow rivet: stainlees steel, mandrel: Stainless steel.Pack = 500 pcs.
54833
Rivet Ø x Clamp Drill Ø mm/ 54833 …Shaft length mm length mm shear strength kp
3 x 6 1,0 - 3,0 3,1 / 205 1013 x 8 3,0 - 5,0 3,1 / 205 102
Rivet Ø x Clamp Drill Ø mm/ 54833 …Shaft length mm length mm shear strength kp
4 x 6 1,0 - 2,5 4,1 / 405 1054 x 10 4,5 - 6,5 4,1 / 405 106
54829
54830
54831
54833
Ü 54829 201
54.20 ENG/OP
H a n d T o o l s
55
Blind Clinch Nuts/Blind Riveters
a54851GBM 10TypeEasy stroke adjustment byuse of knurled nut with strokescale for save setting the blindclinch nut . Threaded mandrelprotection by spring washers,quick exchange of threaded
mandrel without tools. Withopening spring, steel rein-forcements in all high-strainedbearing spots. Ergonomic de-signed and insulated handles. Working range:Aluminium up to M 6,Steel, brass and stainlesssteel up to M 5.
QualityHousing made of pressuredie-cast aluminium,chrome-vanadium steelhandles.
54855Threaded mandrels
54856Nosepieces
Rivet shank Material Drill Pack = 54862 …thread D x L mm thickness mm Ø mm pcs.
M 4 6 x 11,0 0,25 - 3,0 6,1 500 201M 4 6 x 13,0 2,5 - 4,5 6,1 500 202M 5 7 x 11,5 0,25 - 3,0 7,1 500 203M 5 7 x 13,5 2,5 - 5,0 7,1 500 204M 6 9 x 15,5 0,25 - 3,5 9,1 250 305M 6 9 x 18,0 3,0 - 5,5 9,1 250 306
Blind Rivet Assortment
aTypeHand riveter GBM 10 M 5(cat.-no. 54851 102) with ad-ditional threaded mandrelsand nosepieces M 4 / M 6. Dif-ferent blind clinch nut sizes M4 - M 6 made of aluminium formaterials which can be rivetedwith a thickness of 0,25 - 3mm. In box.
54848 …
201
Blind Clinch Nuts with Mushroom Head
a TypeSteel, galvanised and yellowchromed.
54862
Tool Threaded mandrel NosepieceFor blind Length Weight 54851 … 54855 … 54856 …
clinch nuts mm kgM 4 260 0,6 101 101 101M 5 260 0,6 102 102 102M 6 260 0,6 103 103 103
Blind Clinch Nuts with Countersink Head 90°
a TypeSteel, galvanized and yellowchromed. Open round shank.
54864
54848
Rivet shank Material Drill Pack = 54864 …thread D x L mm thickness mm Ø mm pcs.
M 4 6 x 12,0 1,5 - 3,5 6,1 500 301M 4 6 x 13,5 3,0 - 5,0 6,1 500 302M 5 7 x 13,5 1,5 - 4,0 7,1 500 303M 5 7 x 15,5 3,5 - 6,0 7,1 500 304M 6 9 x 17,0 1,5 - 4,5 9,1 250 405M 6 9 x 19,0 4,0 - 6,5 9,1 250 406
54848
54851 - 54856
54864
54862
54851
54855
54856