ß Hand tools - Hommel Hercules Werkzeughandel GmbH &...
Transcript of ß Hand tools - Hommel Hercules Werkzeughandel GmbH &...
ß Hand tools
eng/OP www.hhw.de 54.1
5
Machinist’s hammers DIN 1041
TypeSmoothly ground on all sides, black varnished,polished hammering surfaces.
Note:Soft caps see cat.-no. 54016.
54000
0TypeWith nylon handle protection sleeve. Doublycurved hickory handle, ring wedge.
54002ßTypeDoubly curved ashwood handle.
54000Hickory handle Ashwood handle
Weight without handle Handle length 54000 … 54002 …g approx. mm
200 280 201 102300 300 202 103400 310 203500 320 204 105600 330 205800 350 206 107
1000 360 207 1081500 380 208 1092000 400 209 110
54000 - 54002
Machinist’s hammers (DIN 1041)
bTypeHammer head in compliance with DIN 1041.Drop-forged steel, accurately ground, hardened andtempered, both faces smoothly ground. Doublycurved hickory handle. QualitySteel C 45 acc. to DIN 17200.
Note:Soft caps see cat.-no. 54016.
54003TypeWithout impact protection sleeve.
54005TypeWith nickel-plated impact protection sleeve,pressed into the hammer head.
54007Model INDUTypeWith impact protection on both sides by means ofelectro-inductively tempering, non-slip hickoryhandle and nickel-plated impact protectionsleeve.
54003 - 54007
54007
High-qualitysteel C 45
Ring wedge forsecure seat
Hardened andtempered on allsides (50-58 HRC)
Followingtheregulations, edgesroundedon allsides
DIN eyeletwith pressed-in steel sleevefor preventinghandlebreakage atfailedimpacts.
Impact protection sleeve INDUWeight without handle Handle length 54003 … 54005 … 54007 …
g approx. mm100 260 101200 280 102300 300 103 103 103400 310 104500 320 105 105 105600 330 106800 350 107 107 107
1000 360 108 108 1081500 370 109 109 1092000 400 110 110 110
Hardnessin eyeletarea max. 30 HRC
Double curvedhickory handle
54003
Machinist’s hammers DIN 1041
bTypeSmoothly ground on all sides, black varnished,polished hammering surfaces.
Note:Soft caps see cat.-no. 54016.
54009TypeWith unbreakable ULTRAMID plastic handle, safetywedge, therefore hammer head does not loosen.
54015TypeWith ULTRATEC three-component glass-fibrehandle, unbreakable glass-fibre core. Handlepermanently bonded to hammer head. Non-slipelastomer handle coating. Base coating made ofpolypropylene.
54009 - 54015
54009
54015
ULTRAMID ULTRATECWeight without handle Handle length 54009 … 54015 …
g approx. mm200 280 101 101300 300 102 102500 320 103 103800 350 104 104
1000 360 105 105
54002
eng/OP
• Machinist’s hammers • Carpenter’s hammers • Stonemason's hammer • Sledge hammers
www.hhw.de54.2
5
54025
Machinist's hammers MaxxCraft
54020
Weight without handle Length 54020 …g mm
300 300 101500 320 102800 350 103
1.000 360 104
54020
Soft caps
TypeMade of polyurethane.
ApplicationFor machinist's hammers for use as soft facehammers in compliance with DIN 1041 (cat.-no.54000 - 54020).
54016
For hammer weight 54016 …g
300 101500 102800 103
1000 104
54016
Carpenter’s hammers DIN 5109
bTypeDrop-forged steel, accurately ground, hardened andtempered, both faces smoothly ground. Curvedashwood handle.
QualitySteel C 45 acc. to DIN 17200.
54025
Size . Weight without handle 54025 …mm g
22 230 10325 320 10428 450 105
54048
54053 101-104
54055
54053 105-107
Stonemason's hammer
TypeBlack varnished, polished hammering surfaces.
54048ßTypeDIN 6475. With curved ashwood handle, ringwedge for secure handle seat.
54053bTypeWith ULTRATEC three-component glass-fibrehandle, unbreakable glass-fibre core. Non-slipelastomer handle coating. Base coating made ofpolypropylene.
54053 101-104TypeDIN 6475. Handle permanently bonded to hammerhead.
54053 105-107TypeSecure seat thanks to conical force fit.
54055bTypeDIN 6475. With steel pipe handle and plastic grip,black varnished.
54048 - 54055
ß b bWeight without handle Handle length 54048 … 54053 … 54055 …
kg approx. mm1,00 250 101 101 1011,25 260 102 102 1021,50 270 103 1032,00 280 104 1043,00 900 1055,00 900 107
Type Noticeable dampening of the recoil and therefore thefull force is transferred to the workpiece. Non-tiringand low-impact application thanks to reducedvibration. In order to protect from missed strokes,the handle is covered with rubber. Drop-forgedhammer head made of high-quality special steelwith brightly-ground sides and rounded edges, incompliance with the regulations. All sides thoroughly
hardened and tempered. Thanks to the specialconnection of hammer head with the handle, bothare connected non-detachably and vibration-redu-cing. Ergonomically shaped hickory handle.
Note: Soft caps see cat.-no. 54016.
ß Hand tools
eng/OP www.hhw.de 54.3
5
Sledge hammers
bTypeForged, hardened and tempered with care.QualitySteel C 45 acc. to DIN 17200.
54065TypeDIN 1042. With straight ashwood handle.
54070TypeWith ULTRATEC three-component glass-fibrehandle, unbreakable glass-fibre core. Secure seatthanks to conical force fit. Non-slip elastomer handlecoating. Base coating made of polypropylene.
54065
Ashwood handle ULTRATECWeight without handle Handle length 54065 … 54070 …
kg approx. mm3 600 1024 600 1035 800 1046 800 1058 900 106
10 900 1073 900 1024 900 1035 900 104
54070
54065 - 54070
Spare handles for machinist’s hammers
54071TypeAshwood, straight, top quality, DIN 5111.
54073TypeHickory, doubly curved, top quality, DIN 5111.
Note:cat.-no. 54073 101 straight shape.
54071
Ash wood Hickory woodFor hammer weight Handle length Head end 54071 … 54073 …
g mm mm100 260 17/10 101 101200 280 19/11 102 102300 300 21/12 103 103400 310 24/14 110 110500 320 26/15 104 104600 330 28/16 105 105800 350 29/17 106 106
1000 360 31/18 107 1071500 380 33/20 108 1082000 400 37/22 109 109
54073
54071 - 54073
Spare handles for machinist’s hammers54075 - 54077
b54075TypeHickory, doubly curved, top quality. With ringwedge.ApplicationFor hammers with impact protection sleeve (cat.-no. 54005 - 54007).
54076TypeHickory, doubly curved, top quality, non-slip.With ring wedge.ApplicationFor hammers with impact protection sleeve (cat.-no. 54005 - 54007).
54077TypeHigh-quality plastic ULTRAMID with safety wedgefor permanent, secure seat, complete with wedgeand pin.ApplicationFor all hammers in compliance with DIN 1041.
54075
54076
54077Hickory Hickory ULTRAMID
For hammer Handle length Handle 54075 … 54076 … 54077 …weight g approx. mm end mm
200 280 19/11 102300 300 21/12 103 103 103
400/500 320 26/15 104 104 104800 350 29/17 106 106 106
1000 360 31/18 107 107 1071500 380 33/20 108 1082000 400 37/22 109 109
eng/OP
• Spare handles • Handle Wedges • Light Metal Hammer • Copper Hammer • Mallets • Rubber Mallets
www.hhw.de54.4
5
Spare handles for sledge hammers
54081TypeAshwood, straight, top quality, DIN 5112.
Note:Cat.-no. 54081 101 curved shape.
54083TypeHickory, straight, top quality, DIN 5112.
54081
Ash wood Hickory woodFor hammer weight Handle length Head end 54081 … 54083 …
kg approx. mm mm3 - 4 600 42/24 101 1015 - 6 800 48/48 102 102
8 - 10 900 52/32 103 103
54083
54081 - 54083
Spare handles for machinist's hammers MaxxCraft
54079
For hammer weight Handle length 54079 …g mm
300 265 101500 280 102800 305 103
1000 310 104
54079
Spare handles for stonemason's hammers
54087TypeAshwood, curved, top quality, DIN 5135.
54089TypeHickory, curved, top quality, DIN 5135.
54087 - 54089
Ash wood Hickory woodFor stone mason's hammer weight Handle length Head end 54087 … 54089 …
kg approx. mm mm1 - 1,25 260 31/18 101 101
1,50 280 33/20 102 1022,00 300 37/22 103 103
54087
54089
Safety handle wedges (S-FIX claw wedges)
TypeFor a permanent connection between tool andhandle. Anchorage by means of claws. Newly
designed wedge jaws provide higher expansion.Insert wedge into the handle diagonally withoutsawing.
54095
Light metal hammers
TypeCylindrical, with doubly curved hickory handle andadditional reinforcement to the handle.
ApplicationFor straightening dents and workpieces.
54104
Striking face Ø Head length Weight 54104 …mm approx. mm approx. g
40 75 250 20140 105 350 20250 92 500 20360 98 750 20460 128 1000 205
54104
54095
Size Width For hammer weight 54095 …mm approx. g a
00 13 100 - 200 10 pcs. 2010 16 250 - 400 10 pcs. 2021 20 500 - 800 10 pcs. 2032 23 1000 - 1500 10 pcs. 2043 26 1750 - 2000 10 pcs. 2054 29 3000 - 5000 10 pcs. 2065 32 axes, hatchets 10 pcs. 207
5.1/2 40 axes, hatchets 10 pcs. 2086 50 axes, hatchets 10 pcs. 209
. a= Sales are restricted to the packaging units mentioned
in the catalogue. Purchase orders must be in units.
Type Hickory, ergonomically shaped.
Application For machinist's hammers MaxxCraft (cat.-no.54020).
ß Hand tools
eng/OP www.hhw.de 54.5
5
Copper hammers
54118Type Similar to DIN 5130. Made of drawn steel bars,square-end. With doubly curved ashwood handle.
54120 Type DIN 5130. Made of drawn steel bars, square-end,fully ground. With doubly curved hickory handle.
54118 - 54120
54118 - 54120
Weight Brinell hardness 54118 … 54120 …approx. g
250 80 - 110 200500 80 - 110 201750 80 - 110 202
1000 80 - 110 2031500 80 - 110 2042000 80 - 110 2052500 60 - 80 2063000 60 - 80 2074000 60 - 80 2085000 60 - 80 209
Mallets DIN 7462/B
TypeCommon beechwood, with pressed-on metal sheathand oval ashwood handle.
54130
54130
Head Ø x head length Weight 54130 …mm approx. g
50 x 100 220 10160 x 120 370 10270 x 140 560 10380 x 160 810 10490 x 180 1100 105
Composition rubber mallets DIN 5128-90
54150TypeWith two flat faces and ashwood handle, approx. 95Shore-hardness, strong impact but low rebound.
54151Spare handles
54150
Hammer Spare handleØ B Ø C A L Weight with handle 54150 … 54151 …mm mm mm mm g
40 35 75 280 250 10150 50 90 300 350 102 10260 60 110 330 550 103 10370 70 120 380 750 104 10490 90 130 380 1120 105 105
54150 - 54151
Special bumping mallets
VType Flexible filling material for workpiece-friendlyhammering.
54152 101TypeHandle adjustable by 90°.
54152
Rubber part Overall length 54152 …mm mm
70 x 70 260 10070 x 140 280 101
54152 100
54152 101
eng/OP
• Soft face hammer • Plastic hammer
www.hhw.de54.6
5
54161
Head Ø Weight 54161 …mm approx. g
30 270 10135 385 10245 620 10350 860 10460 1340 105
Recoilless soft face hammers
54153
Hickory handle Steel pipe handle ULTRATEC Nylon head Spare handleHead Ø x Overall Weight approx. g cat.-no. 54153 … 54154 … 54155 … 54156 … 54158 …
head length mm length approx. mm 54153 54154 5415525 x 105 305 280 370 - 101 101 101 10130 x 110 330 400 520 - 102 102 102 10235 x 110 340 550 650 - 103 103 103 10240 x 115 360 700 820 780 104 104 204 104 10350 x 120 370 1000 1140 1090 105 105 205 105 10360 x 145 370 1650 1770 1660 106 106 206 106 10480 x 200 880 4000 - - 107 107 105
100 x 210 1000 7000 - - 108 108 106
54154
54156 54158
54155
54153 - 54158
Recoilless soft face hammers
bTypeHammer head made of metal, with steel shot filling,completely plastic-coated, particularly impact-resis-tant due to a special plastic composition. Tempera-ture-resistant from -20° - +90°C.
ApplicationFor a save treatment of workpieces.
54161
Recoilless soft face hammer54165
Size Weight 54165 …mm approx. g
Soft face hammer 40 700 101Spare heads (pair) 30 x 40 – 102
54165 102
54165 101
SupercraftTypeExchangeable hammer heads.
Note:Double-impact effect, which transmits almost 100%of the impact load to the workpiece (compared withabout 55% with conventional hammers). Rebounddelay through loose steel shot filling in hammerhead.
54153TypeWith nylon-heads and hickory handle.
54154TypeWith nylon heads and steel pipe handle with rubbergrip.
54155TypeWith nylon heads and ULTRATEC three-componentglass-fibre handle, unbreakable glass-fibre core.Handle permanently bonded to hammer head. Non-slip elastomer handle coating. Base coating made ofpolypropylene.
54156Spare nylon heads
54158Spare hickory handles
SECURALTypeSpecial ergonomic designed metal hammer housingwith rubber handle. Heads made of polyurethane,exchangeable, size 30 x 40 mm.
ApplicationFor multi-purpose use with high security standard.
ß Hand tools
eng/OP www.hhw.de 54.7
5
Plastic hammers
54172TypeMiddle part made of grey cast iron, exchangeableheads and wooden handle.
54172 100-105Heads made of impact-proof plastics, red, transpa-rent,
54172 106Heads made of nylon, white.
54173Spare headsPairs.
54172 100-105
Hammer Spare heads (pair)Heads Head Ø xHandle length Weight 54172 … 54173 …
made of mm approx. mm approx. gplastics 22 252 140 100 100plastics 27 265 215 101 101plastics 32 280 310 102 102plastics 35 298 395 105 105plastics 40 320 530 103 103plastics 50 340 800 104 104
nylon 50 340 800 106 106
54172 106
54173 100-105 54173 106
54172 - 54173
Plastic hammers
,TypeCentre piece made of malleable cast iron, withimpact-proof, exchangeable impact heads (roundedfaces), hardwood handles. Resistant against almostall mineral oil, fats and solvents.
54175TypeHeads blue.ApplicationFor standard duty.
54176TypeHeads yellow, particularly ductile and wear-resis-tant.ApplicationFor highest demands (hammer faces will not crack).
54177HeadsBlue, 2 rounded faces, in pairs.
54179HeadsYellow, 2 rounded faces, in pairs.
54175
blue yellow heads blue heads yellowHead Ø x Overall length Weight 54175 … 54176 … 54177 … 54179 …
head length mm approx. mm approx. g22 x 80 260 160 101 101 101 10127 x 90 280 230 102 102 102 102
32 x 100 300 325 103 103 103 10335 x 106 320 415 104 104 104 10440 x 112 340 570 105 105 105 10550 x 120 360 920 106 106 106 10660 x 125 380 1280 107 107 107
54176
54175 - 54179
Simplex soft face hammer54183 - 54188
Composition rubber Plastics Housing Spare handleImpact tip Head length Hammer length Weight 54183 … 54184 … 54186 … 54188 …
mm mm mm approx. g30 90 300 350 101 101 301 10140 110 330 655 102 102 302 10250 135 350 1130 103 103 303 10360 145 405 1610 104 104 304 10480 175 490 3150 105 305 105
54183
54184
5418854186
Type5 sizes and 6 impact tips with different hardnesses(see cat.-no. 54190 - 54195) make the Simplex softface hammer a multi-purpose tool. Clamping withone screw! No wedging! All heads of the same sizecan be combined at will.
54183TypeComplete with two-part housing made of malleablecast iron, Simplex handle and rubber impactheads.
54184TypeComplete with two-part clamping housing made ofmalleable cast iron, Simplex handle and plasticimpact heads.
54186Clamping housing made of malleable cast iron,single, two-part with clamping screws.
54188Spare handles, hardwood.
eng/OP
• Soft face hammer • Carpenter's roofing hammers • Masonry hammer • Plasterer's hatchet • Centre punches and Drift punches
www.hhw.de54.8
5FERROPLEX hammers
54197
Head Ø x head length Overall length Weight 54197 …mm approx. mm approx. g
30 x 104 290 600 101
54197
Impact tips for simplex soft face hammers
54190
TPE-soft rubber plastics Superplastik nylon soft metalTip Ø 54190 … 54191 … 54192 … 54193 … 54194 … 54195 …
mm30 101 101 101 101 101 10140 102 102 102 102 102 10250 103 103 103 103 103 10360 104 104 104 104 104 10480 105 105 105 105
54191
54192 54193
54194 54195
54190 - 54195
Weight 54200 …g
800 201780 202
Carpenter's roofing hammers XSTRIKER with magnet54200
54200 201
54200 202
bTypeProfessional-grade:- head protection TÜV/GS- magnetic nail holder- reinforced steel ring- special plastic handle- XSTRIKER design
54200 201TypePartly polished hammer head.
54200 202TypePolished hammer head. The well-balanced weightdistribution and the special ergonomics of thehandle ensure extraordinary handling.
Weight 54199 …g
780 101
Carpenter's roofing hammer54199
bTypeWith nail holder and head protection TÜV/GS.Tubular steel handle with plastic handle. Roughenedstriking face, black lacquered.
54199
54190TypeTPE-soft, blue, soft impact, colour proofed. Shorehardness approx. 95A.ApplicationSensitive surfaces, e.g. assembly, furniture industry,laying tile, etc.
54191TypeComposition rubber, black, medium impact, Shore-hardness approx. 95 A, special rubber composition.ApplicationMulti-purpose use.
54192TypePlastics, red, hard impact, transparent plastics, fatand oil-resistant.ApplicationMulti-purpose use.
54193TypeSuperplastics, white, very ductile and unbreakableplastics, resistant against fats, oils, acid andalkalines.ApplicationEspecially suitable for edge impacts.
54194TypeNylon, white, hardest impact, high impact efficiencythanks to high elasticity, resistant against fats andoils.ApplicationFor strong adjustment impacts.
54195TypeSoft metal, silver, very high impact force, light-metalspecial alloy, heat-resistant.ApplicationReplaces standard lead hammers.
Type 2 in 1: machinist's hammer and soft face ham-mer. Hammer heads: tempered steel impact headand exchangeable nylon impact head. Steel pipehandle permanently bonded to hammer head.
Quality Impact face hardened and tempered.
Note:Spare nylon heads see cat.-no. 54156 102.
ß Hand tools
eng/OP www.hhw.de 54.9
5
54202
Masonry hammer
bTypeBerlin form, with steel pipe handle and plastichandle, black lacquered, smooth impact face.
54202
Weight 54202 …ca. g
750 101
Masonry hammer
bTypeShape: Rheinisch. With steel pipe handle andplastic grip, black varnished.
54203
Weight 54203 …ca. g
600 101
54203
Plasterer's hatchet
bTypeWith steel pipe handle and plastic grip, blackvarnished, polished edge, roughened impact face.
54204
Weight 54204 …ca. g
700 101
54204
Hammering tool set
JType 19-part, in plastic case. Sheathed, low-vibration andimpact-dampening comfort handle with exchange-able inserts made of 3 different materials: brass,polyamide, aluminium.The insert-system allows foran efficient choice of the hardness, in order toprevent workpiece damage. Mounting by means ofM10 thread. The insert ring dampens the impacts,the thread will not be damaged.
Application For working on all types of axes, shafts, pins,bearings. Perfect for Cardan shafts, gearings. Forremoving, replacing and tightening of workpieces: Brass inserts: Hardness HV.155 (430-500 N/mm2), Polyamide inserts: Shore hardness 85D, Aluminium inserts: 370 N/mm2.
Set contents 54297 …
19-part 101
54297
54297
Set contents: . 1 comfort handle, . 3 brass inserts Ø 12 / 16 / 20 mm, usable length 40 mm, . 3 polyamide inserts Ø 12 / 16 / 20 mm, usable length 40 mm, . 5 aluminium inserts Ø 10 / 12 / 14 / 16 / 18 mm, usable length 60 mm, . 1 extension, usable length 100 mm, . 3 brass inserts for extension Ø 12 / 16 / 18 mm, usable length 20 mm, . 3 polyamide inserts for extension Ø 12 / 16 / 18 mm, usable length 20 mm.
Set contents 54295 …
6-part 101
Set of centre punches and drift punches54295
ßTypeOctagonal, shank lacquered, safety zone especiallyelectro-inductive hardened.6-part: 1 centre punch DIN 7250, 120 x 10 x 4 mm,5 drift punches DIN 6458, 120 x 10 x 2-6 mm,(dimensions = overall length x shank Ø x end oftaper Ø), in sheet metal box.
QualityChrome-vanadium air-hardened steel. 54295
eng/OP
• Centre punch • Drift punches
www.hhw.de54.10
5
Centre punch
ßTypeKnurled shank.
QualityHardened steel.
54300
Shank Ø Overall length 54300 …mm mm
8 100 101
54300
Centre punch with carbide tip
ßTypeHexagonal end, with carbide pointed tip, regrinda-ble.
54303
Shank Ø Overall length 54303 …mm mm
12 120 101
54303
Centre punches with handle
JTypeVibration damp handle, good grip and ergonomicdesigned, with finger guard, not affected by changesin temperature. Hardened head of 43 HRc, to avoidcracking. Tip hardness 58 HRc. Grip comfort and
vibration characteristic ensures high precision andstrong impact.
54309
Tip Ø Shank Ø Overall length 54309 …mm mm mm2,5 10 185 1014,0 10 185 1026,0 10 185 1038,0 12 185 104
10,0 14 185 105
54309
Tip Ø Shank Ø Overall length 54308 …mm mm mm
4 10 120 1015 10 150 102
Centre punches with hand guard DIN 725054308
ßTypeWith ergonomically shaped handle and large handguard. Octagonal, forged, impact head tempered,shank lacquered, safety zone thanks to electro-in-ductive special hardening procedure.
QualityChrome-vanadium air-hardened steel. 54308
ß ,
Tip Ø Shank Ø Overall length 54305 … 54306 …mm mm mm
3 8 100 1014 10 120 201 1025 12 120 2025 12 150 203 103
Centre punches DIN 7250
54305ßTypeOctagonal, forged, impact head tempered, shanklacquered, safety zone thanks to electro-inductivespecial hardening procedure.QualityChrome-vanadium air-hardened steel.
54306,TypeOctagonal, glossy nickel-plated, with plastic handguard.QualityVanadium-extra steel.
54305
54306
54305 - 54306
Performance requires quality.www.atorn.com
Burrs by ATORN:
ATORN‘s high-quality grinding and cutting tools.
ß Hand tools
eng/OP www.hhw.de 54.11
5
Adjustable centre punches
TypeThe punch consists of punching pin, guide bushing,and centring sleeve. Application For transmitting of existing boreholes to otherworkpieces. Application 1. Insert centre punch into borehole. 2. Extent the centring flaps until they completely
touch the borehole. 3. Hit the pin with the hammer.
54319 3-part setin plastic box.
54319
Set singlefor Borehole Ø 54319 … 54320 …
mmSet 6 - 16 101
6 - 8 1018 - 11 102
11 - 16 103
54319 - 54320
Automatic centre punch
54314TypeWith spring-loaded mechanism, tips exchangeable,adjustable impact.ApplicationFor one-hand operation.QualitySpecial steel.
54315Spare tip.
54314 - 54315
Centre punch Spare punch pointShank Ø Overall length 54314 … 54315 …
mm mm17 130 201 201
54314
54315
Drift punches DIN 6458
ßTypeOctagonal, forged, tempered impact head, varnis-hed shank. Safety zone thanks to electro-inductivespecial hardening process.ApplicationFor driving out rivets, bolts, etc.
QualityChrome-vanadium air-hardened steel. 54321
Tip Ø Shank Ø Overall length 54321 …mm mm mm
1 10 120 2012 10 120 2023 10 120 2034 10 120 2045 12 120 2056 12 120 2067 12 120 2078 12 120 208
10 14 150 20912 14 150 21015 18 175 211
54321
eng/OP
• Drift punches • Drive pin punches
www.hhw.de54.12
5
Set contents Tip Ø 54325 …mm
5-part 2 / 3 / 4 / 5 / 6 101
Tip Ø Shank Ø Overall length 54325 …mm mm mm
2 10 120 2013 10 120 2024 10 120 2035 10 120 2046 10 120 2058 10 120 206
Drift punches with hand guard DIN 6458 B54325
ßTypeWith ergonomically shaped handle and large handguard. Octagonal, forged, impact head tempered,shank lacquered, safety zone thanks to electro-in-ductive special hardening procedure.
ApplicationFor driving out rivets, bolts, etc.QualityChrome-vanadium air-hardened steel.
54325 101
54325 201-206
Drift punches DIN 645854327
,TypeOctagonal, with plastic hand guard.
ApplicationFor driving out rivets, bolts, etc.QualityVanadium-extra steel, nickel-plated.
54327
Tip Ø Shank Ø Overall length 54327 …mm mm mm
2 10 120 1013 10 125 1024 10 130 1035 10 165 1056 10 180 1068 12 200 107
Set of drive pin punches DIN 6450 C
ßTypeLength 150 mm, Octagonal, impact head tempered,shank with golden finish, in sheet metal box.
QualityChrome-vanadium air-hardened steel, forged. 54349
Set contents Tip Ø 54349 …mm
6-part 3 / 4 / 5 / 6 / 7 / 8 101
54349
Set of drive pin punches
VTypeLength 150 mm, octagonal, matt black, in plasticstand.
QualityChrome-vanadium air-hardened.
54350
Set contents Tip Ø 54350 …mm
6-part 2 / 3 / 4 / 5 / 6 / 8 101
54350
Set contents Tip Ø 54347 …mm
6-part 3 / 4 / 5 / 6 / 8 / 10 101
Set of drive pin punches54347
TypeLength 150 mm, Shank Ø 10 mm. Chrome-platedand powder-coated in colours. Shatterproof, long-lasting, and non-slip surface coating.
QualityFully tempered, high-alloyed tool steel withincreased hardness of more than 59 HRC.
54347
ß Hand tools
eng/OP www.hhw.de 54.13
5
Set contents Tip Ø 54353 …mm
5-part 2 / 3 / 4 / 5 / 6 1015-part 8 / 10 / 12 / 14 / 16 102
Tip Ø Shank Ø Overall length 54353 …mm mm mm
2 10 150 2013 10 150 2024 10 150 2035 10 150 2046 10 150 2058 10 150 2068 14 225 207
10 14 240 20812 14 260 20914 18 275 21016 18 290 211
Drive pin punches with hand guard DIN 645054353
ßTypeWith ergonomically shaped handle and large handguard. Octagonal, impact head tempered, shankgolden.QualityChrome-vanadium air-hardened steel, forged.
54353 10154353 102
54353 201-206
54353 207-211
Drive pin punches with handle
JTypeVibration damp handle, good grip and ergonomicdesigned, with finger guard, not affected by changesin temperature. Hardened head of 43 HRc, to avoidcracking. Tip hardness 58 HRc. Grip comfort and
vibration characteristic ensures high precision andstrong impact.
54351 - 54352
54351
Set contents Tip Ø 54351 …mm
7-part 1,9 / 2,9 / 3,9 / 4,9 / 5,9 / 7,9 / 9,8 102
Tip Ø Shank Ø Overall length 54352 …mm mm mm1,9 10 175 1012,9 10 190 1023,9 10 195 1034,9 10 205 1045,9 12 210 1057,9 12 220 1069,8 14 230 107
Set of drive pin punches with guide bushings
ßTypeWith knurled, nickel-plated guide bushings, insheet metal box.ApplicationLocate the point with the guide bushing in a fullyforward position. During drifting the bushing slidesback thus continuing to support the punch point.QualityChrome-vanadium steel, highly polished.
Note:Pin Ø 5,9 mm without guide bushing.
54359
Set contents Tip Ø 54359 …mm
8-part 0,9 / 1,4 / 1,8 / 2,4 / 2,8 / 3,4 / 3,9 / 5,9 101
54359
Performance requires quality.www.atorn.com
Tool carts by ATORN:
ATORN‘s high-quality workshop furnishings.
eng/OP
• Drive pin punches • Chisels
www.hhw.de54.14
5Drive pin punches
ßTypeKnurled shank. Zinc chromised.
54382
Tip Ø Shank Ø Overall length 54382 …mm mm mm
1 6 100 1012 6 105 1023 8 110 1034 8 115 1045 8 120 105
Tip Ø Shank Ø Overall length 54382 …mm mm mm
6 10 125 1067 10 130 1078 12 135 1089 12 140 109
54382
Drive pin punches DIN 6450 C
ßTypeOctagonal, impact head tempered, shank golden.
QualityChrome-vanadium air-hardened steel, forged. 54380
Tip Ø Shank Ø Overall length 54380 …mm mm mm
2 10 150 1013 10 150 1024 10 150 1035 10 150 1046 10 150 105
Tip Ø Shank Ø Overall length 54380 …mm mm mm
7 12 150 1068 12 150 107
10 12 150 10812 14 150 109
54380
Set of drive pin punches with guide bushings
,TypeDriving points finely ground and polished, withknurled, nickel-plated guide bushings, in plasticstand.ApplicationLocate the point with the guide bushing in a fullyforward position. During drifting the bushing slidesback thus continuing to support the punch point.
QualityVanadium-extra steel, nickel-plated and chrome-plated.
Note:Tip Ø 5,9 mm without guide bushings.
54364
Set contents Tip Ø 54364 …mm
8-part 0,9 / 1,4 / 1,8 / 2,4 / 2,8 / 3,4 / 3,9 / 5,9 101
54364
Drive pin punches DIN 6450 D
,TypeOctagonal, driving points finely ground and polished,with plastic hand guard.
QualityVanadium-extra steel, nickel-plated.
54383
Tip Ø Shank Ø Overall length 54383 …mm mm mm
2 8 115 1013 8 125 1024 10 150 103
Tip Ø Shank Ø Overall length 54383 …mm mm mm
5 10 165 1046 12 180 1058 12 200 106
54383
ß Hand tools
eng/OP www.hhw.de 54.15
5
Drive pin punches
TypeWith knurled and nickel-plated guide bushing.ApplicationLocate the point with the guide bushing in a fullyforward position. During drifting the bushing slidesback thus continuing to support the punch point.
Note:Tip Ø 5,9 mm without guide bushings.
54385ßQualityChrome-vanadium steel, zinc chromised.
54390,QualityVanadium-extra steel, nickel-plated and chrome-plated.
54385 - 54390
ß ,
Tip Ø Overall length 54385 … 54390 …mm approx. mm0,9 75 101 1011,4 85 102 1021,8 85 103 1032,4 90 104 104
ß ,
Tip Ø Overall length 54385 … 54390 …mm approx. mm2,8 95 105 1053,4 95 106 1063,9 100 107 1075,9 100 108 108
54385
54390
Tool set
ßTypeSafety zone thanks to electro-inductive specialhardening process. Impact head tempered.
6-part:1 ea.flat chisel 125 and 150mm,1 cape chisel 125mm,1 centre punch 120mm,1 ea. drift punch 2 and 3 mm, in sheet metal box.QualityChrome-vanadium air-hardened steel, forged.
54592
Set contents 54592 …
6-part 101
54592
Flat chisels DIN 6453
ßTypeFlat-oval body, forged, varnished shank, fullyregrindable cutting edge, striking face tempered.Safety zone thanks to electro-inductive special
hardening process. Cutting edge ground andvarnished.QualityChrome-vanadium air-hardened steel.
54601
Cutting edge width Shank size Overall length 54601 …mm mm mm
15 14 x 9 100 10118 14 x 9 125 10218 17 x 11 150 10321 20 x 12 175 104
Cutting edge width Shank size Overall length 54601 …mm mm mm
24 23 x 13 200 10525 23 x 13 250 10626 23 x 13 300 107
54601
Cape chisels DIN 6451
ßTypeFlat-oval body, forged, varnished shank, fullyregrindable cutting edge, striking face tempered. Safety zone thanks to electro-inductive specialhardening process. Cutting edge ground and
varnished.QualityChrome-vanadium air-hardened steel.
54605
Cutting edge width Shank size Overall length 54605 …mm mm mm5,5 14 x 9 125 1026,0 17 x 11 150 1037,0 17 x 11 175 104
Cutting edge width Shank size Overall length 54605 …mm mm mm8,0 20 x 12 200 1059,0 23 x 13 250 1069,0 23 x 13 300 107
54605
Grooving chisels DIN 6455
ßTypeOctagonal, varnished shank, striking face tempered.
QualityChrome-vanadium air-hardened steel.
54620
Cutting edge width Shank Ø Overall length 54620 …mm mm mm
3 10 150 1024 10 150 103
Cutting edge width Shank Ø Overall length 54620 …mm mm mm
5 10 150 104
54620
eng/OP
• Chisels • Riveters • Rivet head formers • Blind rivet assortment
www.hhw.de54.16
5
Web chisels
ßTypeTwo cutting edges with clearance angle all-around.Octagonal, varnished shank, striking face tempered.ApplicationFor removing webs between drill holes.
QualityChrome-vanadium air-hardened steel.
Note:The shape of the double cutting edge preventsdeformation or upsetting on the workpiece.
54622
Cutting edge width Shank Ø Overall length 54622 …mm mm mm
2 10 125 1013 10 125 102
Cutting edge width Shank Ø Overall length 54622 …mm mm mm
4 12 150 1035 12 150 104
54622
Electrician’s slotting chisel
ßTypeWith hand guard, 2 cutting edges, forged, impacthead tempered, gold-lacquered, cutting edgeground and lacquered.
QualityChrome-vanadium air-hardened steel. 54625
54625
Cutting edge width Shank size Overall length 54625 …mm mm mm
34 23 x 13 250 202
Slotting chisel
ßTypeForged, striking face tempered, gold-lacqueredshank, cutting edge ground and varnished.
ApplicationFor metal and masonry work.QualityChrome-vanadium air-hardened steel.
54624
Cutting edge width Shank size Overall length 54624 …mm mm mm
26 26 x 7 240 102
54624
Moil point chisels DIN 7256
ßTypeOctagonal, forged, impact head tempered, shaftgold-lacquered, cutting edge ground and lacquered.
QualityChrome-vanadium air-hardened steel. 54650
Shank Ø Overall length 54650 …mm mm
16 200 10116 250 10218 300 103
Shank Ø Overall length 54650 …mm mm
20 400 10420 500 105
54650
Stone chisel DIN 7254 BßTypeOctagonal, forged, impact head tempered, shaftgold-lacquered, cutting edge ground and lacquered.
QualityChrome-vanadium air-hardened steel. 54656
Cutting edge width Shank Ø Overall length 54656 …mm mm mm
23 16 200 10123 16 250 10226 18 300 103
Cutting edge width Shank Ø Overall length 54656 …mm mm mm
30 20 400 10430 20 500 105
54656
Shank size Overall length 54623 …mm mm
26 x 7 240 101
Slotting chisel with offset operative end54623
ßTypeOperative end offset 25° - for safe operationthanks to increased space for the hand. Perfectcutting edge geometry. Additional lateral cuttingedge for slotting and cutting. Impact headaftertreated inductively. Cutting edges can be
ground. Operative end lacquered. Shank with golden finish.
ApplicationFor mortising, cutting, and slotting.QualityChrome-vanadium steel, fully steel tempered incompliance with DIN 7255.
54623
ß Hand tools
eng/OP www.hhw.de 54.17
5
Electrician’s stone chisels
ßTypeForged, striking face tempered, gold-lacqueredshank, cutting edge ground and varnished.
QualityChrome-vanadium air-hardened steel. 54665
Cutting edge width Shank Ø Overall length 54665 …mm mm mm
10 8 200 20110 8 250 20312 10 200 202
Cutting edge width Shank Ø Overall length 54665 …mm mm mm
12 10 250 20414 12 300 205
54665
Chisel hand guard
ßApplicationMulti-purpose use, for flat-oval 20 x 12 mm and 26 x13 mm, and for octagonal 16 - 20 mm.
54680
Overall length 54680 …mm110 101
54680
Riveters DIN 6434
TypeOctagonal, with safety striking face.Set in plastic box.
QualityChrome-vanadium air-hardened steel.
For rivet shank Ø 54812 …mm
2 1013 1024 1035 104
Set 5-part 2 / 3 / 4 / 5 / 6 105
54812
54812 105
Rivet head formers DIN 6435
TypeOctagonal, with safety striking face.Set in plastic box.
QualityChrome-vanadium air-hardened steel.
54814
For rivet shank Ø 54814 …mm
2 1013 1024 1035 104
Set 5-part 2 / 3 / 4 / 5 / 6 105
54814 105
Blind rivet assortment54820
OTypeContents:1 hand riveter model NTX (cat.-no. 54825) and 12 blind rivet sizes, 3 mm and 4 mm Ø made ofdifferent materials, in sheet metal case.
54820 …
101
54820
eng/OP
• Hand riveters • Blind rivet guns
www.hhw.de54.18
5
Hand riveter FLIPPER / FLIPPER box
OApplicationFor aluminium alloy rivets up to 5 mm Ø andstainless steel rivets up to 4 mm Ø. Single lift of stroke 1,8 mm.
54824 101Hand riveter FLIPPERTypeReal single-hand use, by 40% reduced expenditureof force. With rivet drop-in box.
54824 102Set of hand riveters FLIPPER boxTypeIn case with 3 kinds of PolyGrip® multi-purpose blindrivets, which replace 11 different sizes of standardrivets.
54824 101
54824 102
for rivet Ø up to rivet Ø x thickness of material pack = 54824 …mm shank length mm mm pcs.
Hand riveter 5 - - - 101Set of hand riveters 5 - - - 102Blind rivet PolyGrip® - 3,2 x 8 0,5 - 5,0 100 201Blind rivet PolyGrip® - 4,0 x 10 0,5 - 6,5 100 203Blind rivet PolyGrip® - 4,8 x 10 0,5 - 6,5 50 205
54824
Set contents 54824 102:1 ea. hand riveter FLIPPER1 pack PolyGrip® multi-purpose blind rivets 3,2 x 8 mm1 pack PolyGrip® multi-purpose blind rivets 4,0 x 10 mm1 pack PolyGrip® multi-purpose blind rivets 4,8 x 10 mm1 ea. plastic case
Mechanical hand riveters
ONote:Spare nosepieces available on request.
54825Model NTXTypeNarrow riveter head, good leverage ratio, with 3nosepieces size 3,2 / 4,0 / 5,0 mm and fittingwrench.ApplicationFor aluminium rivets up to 5 mm Ø and stainlesssteel rivets up to 4 mm Ø.QualityChrome-vanadium steel handles. Housing madeof pressure die-cast aluminium.
54827Model HN 2TypeNo force transmission onto the workpiece surface,with 5 nosepieces size 4,0 / 4,8 / 5,0 / 6,0 / 6,4 mm.ApplicationFor all materials up to 6,4 mm rivet Ø.QualityHousing made of pressure die-cast aluminium.
54825 - 54827
54825
54827
NTX HN 2For rivet Ø Length 54825 … 54827 …
mm mm3,2 - 5,0 260 1014,0 - 6,4 570 201
Mechanical hand riveters
ß TypeWith opening spring, 4 nosepieces size 2,4 3,2 / 4,0 /4,8 mm and fitting wrench.
54821TypeWith narrow riveter head.
54823TypeRiveter head swivels through 360°.ApplicationEasy and quick adjustment in any angle position,therefore most suitable also at difficult to reachspots.
54821
For rivet Ø Length 54821 … 54823 …mm mm
2,4 - 4,8 260 1012,4 - 4,8 300 101
54823
54821 - 54823
3,2x8 replaces 3,2x4 3,2x6 3,2x8
4,0x10 replaces 4,0x5 4,0x6 4,0x7 4,0x8 4,0x10
4,8x10 replaces 4,8x6 4,8x8 4,8x10
54824 201-205
ß Hand tools
eng/OP www.hhw.de 54.19
5
Compressed-air hydraulic blind rivet guns
OTypeGripping mechanism (pat. pending) with positively-driven jaws and pneumatic pressure: Very longservice life, safe and non-slip handle for rivet pins,only one version for all dimensions.High installation forces at low weight, short cycles,optimised stroke.Low air consumption thanks to the double use of theair for installation and removal of the installationpiece in addition to activation of air intake bylockable sliding switch.Comfort and security: Rubberised and perfect-fit-ting handle, balanced centre of gravity, low-vibrationand noise-reduced. Low force needed, collectorwith integrated safety device and rotatable airdeflector, relieve valve.
54834 102TAURUS 2TypeNosepiece in operating position: 17/27. Nosepiecesin the underside: 17/29, 17/32, and 17/36.ApplicationUp to 5 mm Ø all materials and 6 mm Ø alumini-um/steel.
54834 103TAURUS 3TypeNosepiece in operating position: 17/36. Nosepiecesin the underside: 17/40 and 17/45.ApplicationUp to 6,4 mm Ø all materials.
54834 102
54834 103
54834
Blind riveting tool PowerBird and AccuBird
O54829 200-201TypeWell-balanced position of centre of gravity, ergono-mical handle. Discarding of the rivet pin by gravity:to the front through the nosepiece or to the back intothe collector. Immediate reset to initial position afterthe riveting process.
54829 200PowerBirdTypeScope of supply: PowerBird in case with Li-ionrechargeable battery 14,4 V, 2,6 Ah and 1 quickcharger. Nosepieces: 17/32 in operating position,17/36, 17/40, 17/45 in magazine.ApplicationBlind rivet starting at Ø 4,8 mm steel up to 6,4 mmall materials. BULB-TITE® blind rivet up to Ø 7,7 mmall materials. MEGA GRIP® blind rivet up to Ø 6,4mm all materials.Note:Accessories see cat.-no. 54829 205-221.
54829 201AccuBirdTypeScope of supply: AccuBird in case with Li-ionrechargeable battery 14,4 V, 1,3 Ah and 1 quickcharger. Nosepieces: 17/24 in operating position,17/27, 17/29, 17/32 in magazine.ApplicationBlind rivet up to 5 mm Ø all materials. BULB-TITE®
blind rivet 4, 5,2 and 6,3 mm Ø aluminium and steel.
Note:Accessories see cat.-no. 54829 205-221.
54829 205-210Gripper nosepieceApplicationThe inserted rivet is held securely in any position.One-hand riveting. Better safety. For blind rivetingtool PowerBird and AccuBird, cat.-no. 54829 200-201.
54829 220Quick-change rechargeable batteryTypeLi-ion, 14,4 V, 1,3 Ah.ApplicationFor blind riveting tool PowerBird, AccuBird, andFireBird, cat.-no. 54829 200-201 and 54860 101.
54829 221Quick-change rechargeable batteryTypeLi-ion, 14,4 V, 2,6 Ah.ApplicationFor blind riveting tool PowerBird, AccuBird, andFireBird, cat.-no. 54829 200-201 and 54860 101.
54829 200
54829 220
54829 201
54829 221
54829 205-210
Stroke Riveting force Weight 54829 …mm N kg
PowerBird 20 13.000 2,0 200AccuBird 20 8.500 2,0 201
Nosepiece 17/18R - - - 205Nosepiece 17/24R - - - 206Nosepiece 17/27R - - - 207Nosepiece 17/29R - - - 208Nosepiece 17/32R - - - 209Nosepiece 17/36R - - - 210
Rechargeable battery 14,4 V/1,3 Ah - - - 220Rechargeable battery 14,4 V/2,6 Ah - - - 221
54829
Air consumption/riveting process Operating pressure Stroke Riveting force (5 bar) Hose coupling Ø Weight 54834 …approx. ltr. bar mm N mm kg
TAURUS 2 2,3 5 - 7 18 9.000 6 (1/4") 1,6 102TAURUS 3 4,8 5 - 7 25 14.000 6 (1/4") 1,9 103
eng/OP
• Blind rivet • Blind rivet nuts
www.hhw.de54.20
5
Aluminium blind rivets with mushroom head
OTypeHollow rivet: aluminium alloy, rivet pin: galvanisedsteel, melting point approx. 600 °C.
54830
Rivet Ø x shank length Clamping length Borehole Ø Shear strength Pack = 54830 …mm mm mm kp pcs.
2,4 x 4 0,5 - 1,5 2,5 35 1000 1013,0 x 5 1,5 - 2,5 3,1 71 500 1053,0 x 6 2,5 - 3,5 3,1 71 500 1063,0 x 8 4,5 - 5,0 3,1 71 500 108
3,0 x 10 5,0 - 7,0 3,1 71 500 1093,0 x 12 7,0 - 9 0 3,1 71 500 1104,0 x 6 1,5 - 3,0 4,1 143 500 1184,0 x 8 4,0 - 5,0 4,1 143 500 120
4,0 x 10 5,0 - 6,5 4,1 143 500 1214,0 x 12 6,5 - 8,5 4,1 143 500 1224,0 x 16 10,5 - 12,5 4,1 87 500 1235,0 x 8 2,5 - 4,5 5,1 204 500 127
5,0 x 10 4,5 - 6,0 5,1 204 500 1285,0 x 12 6,0 - 8,0 5,1 204 500 1295,0 x 16 10,0 - 12,0 5,1 204 500 1316,0 x 12 5,0 - 7,0 6,1 316 250 237
54830
Aluminium blind rivets with mushroom head
OTypeHollow rivet: aluminium alloy, rivet pin: stainlesssteel.
54831
Rivet Ø x shank length Clamping length Borehole Ø Shear strength Pack = 54831 …mm mm mm kp pcs.
3 x 6 1,5 - 3,5 3,1 71 500 1023 x 8 3,5 - 5,0 3,1 71 500 105
3 x 10 5,0 - 7,0 3,1 71 500 1064 x 6 1,5 - 3,0 4,1 143 500 1124 x 8 3,0 - 5,0 4,1 143 500 114
4 x 10 5,0 - 6,5 4,1 143 500 115
54831
Steel blind rivets with mushroom head
OTypeHollow rivet: galvanised steel, rivet pin: galvanisedsteel.
54832
Rivet Ø x shank length Clamping length Borehole Ø Shear strength Pack = 54832 …mm mm mm kp pcs.
3 x 5 0,5 - 2,0 3,1 112 500 1013 x 6 2,0 - 3,0 3,1 112 500 103
3 x 10 5,0 - 6,5 3,1 112 500 1054 x 8 2,5 - 4,5 4,1 204 500 113
4 x 10 4,5 - 6,5 4,1 204 500 1144 x 12 6,5 - 8,5 4,1 204 500 115
54832
Stainless steel blind rivets with mushroom head
OTypeHollow rivet: stainless steel, rivet pin: stainless
steel.54833
Rivet Ø x shank length Clamping length Borehole Ø Shear strength Pack = 54833 …mm mm mm kp pcs.
3 x 6 1,0 - 3,0 3,1 205 500 1013 x 8 3,0 - 5,0 3,1 205 500 1024 x 6 1,0 - 2,5 4,1 405 500 105
4 x 10 4,5 - 6,5 4,1 405 500 106
54833
ß Hand tools
eng/OP www.hhw.de 54.21
5
Blind rivet nut hand tool
O54851GBM 10TypeEasy stroke adjustment by use of knurled nut withstroke scale for securely setting the blind clinch nut.Threaded mandrel protection by means of springwashers, quick exchange of threaded mandrelwithout tools. With opening spring, steel reinforce-ments in all high-strained bearing spots. Ergonomi-cally designed and insulated handles. Working range:Aluminium up to M 6,Steel, brass and stainless steel up to M 5.
QualityHousing made of pressure die-cast aluminium,chrome-vanadium steel handles.
54855Threaded mandrels
54856Nosepieces
54851
54855
54856
54851 - 54856
Tool Threaded mandrel NosepieceFor blind Length Weight 54851 … 54855 … 54856 …rivet nuts mm kg
M 4 260 0,6 101 101 101M 5 260 0,6 102 102 102M 6 260 0,6 103 103 103
Compressed-air hydraulic blind rivet nut guns
O54857 101-106GBM 95TypeScope of supply: blind rivet nut gun GBM 95,threaded rivet pin and nosepiece, stroke table.ApplicationM 3 - M 10 all materials.
Note:Threaded rivet pins and nosepieces see cat.-no.54857 201-306.
54857 201-206Threaded mandrelsApplicationFor compressed-air hydraulic blind rivet nut gunscat.-no. 54857 101-106.
54857 301-306NosepiecesApplicationFor compressed-air hydraulic blind rivet nut gunscat.-no. 54857 101-106.
54857 101-106
Gun Threaded rivet pin NosepieceFor blind rivet nuts 54857 … 54857 … 54857 …
3 101 201 3014 102 202 3025 103 203 3036 104 204 3048 105 205 305
10 106 206 306
54857
Technical specifications cat.-no. 54857 101-106Air consumption per rivet operation: approx. 8 ltr.Operating pressure: 6 barRiveting force: 15.700 N (1.600 kp)Hose coupling: 6 mm Ø (1/4")Weight: 2,3 kg
Blind rivet nut assortment
OTypeHand riveter GBM 10 M 5 (cat.-no. 54851 102) withadditional threaded rivet pins and nosepieces M 4 /M 6. Different blind rivet nut dimensions M 4 - M 6made of aluminium for thickness of material 0,25 - 3mm. In cassette.
54848
54848 …
201
54848
Performance requires quality.www.atorn.com
Adjustable wrenches by ATORN:
ATORN‘s high-quality hand tools.
eng/OPwww.hhw.de54.22
5
• Blind rivet nuts • Torque screwdriver
Blind rivet nut device FireBird
OFireBirdTypeWell-balanced position of centre of gravity, ergono-mical handle. Simple and safe screwing-on of theblind rivet nuts. Constant riveting speed andautomatic change-over from riveting to removalprocess.Scope of supply: FireBird in case with Li-ionrechargeable battery 14,4 V, 1,3 Ah and 1 quickcharger. Threaded rivet pin M 6 and nosepiece inoperating position. 1 ea. threaded rivet pin andnosepiece M 4 and M 5 in magazine.
ApplicationBlind rivet nuts up to M 10 aluminium, up to M 8steel and up to M 6 stainless steel.
Note:Quick-change rechargeable battery see cat.-no. 54829 220+221.
54860
Riveting force Weight with rechargeable battery 54860 …N kg
13.000 2,1 101
54860
Blind rivet nuts with mushroom head
OTypeSteel, galvanised and yellow chromised.
54862
Thread Rivet shank Thickness of material Drill Ø Pack = 54862 …D x L mm mm mm pcs.
M 4 6 x 11,0 0,25 - 3,0 6,1 500 201M 4 6 x 13,0 2,5 - 4,5 6,1 500 202M 5 7 x 11,5 0,25 - 3,0 7,1 500 203M 5 7 x 13,5 2,5 - 5,0 7,1 500 204M 6 9 x 15,5 0,25 - 3,5 9,1 250 305M 6 9 x 18,0 3,0 - 5,5 9,1 250 306
54862
Blind rivet nuts with countersunk head 90°54864
OTypeSteel, galvanised and yellow chromised. Open roundshank.
54864
Thread Rivet shank Thickness of material Drill Ø Pack = 54864 …D x L mm mm mm pcs.
M 4 6 x 12,0 1,5 - 3,5 6,1 500 301M 4 6 x 13,5 3,0 - 5,0 6,1 500 302M 5 7 x 13,5 1,5 - 4,0 7,1 500 303M 5 7 x 15,5 3,5 - 6,0 7,1 500 304M 6 9 x 17,0 1,5 - 4,5 9,1 250 405M 6 9 x 19,0 4,0 - 6,5 9,1 250 406