Solidworks Tutorial 5 Voor Lager en Middelbaar Technisch Onderwijs 2008 English Tws

5/26/2018 Solidworks Tutorial 5 Voor Lager en Middelbaar Technisch Onderwijs 2008 English Tws

1/35

SolidWorksTutorial 5

TIC-TAC-TOE

Preparatory Vocational Training (VMBO)

and Advanced Vocational Training (MBO)


2/35

To be used with SolidWors!"ducational #elease $%%&'$%%

1995-2009, Dassault Systmes SolidWorks Corp.300 Baker Avenue

Concord, Massachusetts 01742 USA

All Rights Reserved

U.S. Patents 5,815,154; 6,219,049; 6,219,055

Dassault Systmes SolidWorks Corp. is a Dassault Systmes

S.A. (Nasdaq:DASTY) company.

The information and the software discussed in this document

are subject to change without notice and should not be

considered commitments by Dassault Systmes SolidWorks

Corp.

No material may be reproduced or transmitted in any form or

by any means, electronic or mechanical, for any purpose

without the express written permission of Dassault Systmes

SolidWorks Corp.

The software discussed in this document is furnished under a

license and may be used or copied only in accordance with

the terms of this license. All warranties given by Dassault

Systmes SolidWorks Corp. as to the software and

documentation are set forth in the Dassault Systmes

SolidWorks Corp. License and Subscription Service

Agreement, and nothing stated in, or implied by, this

document or its contents shall be considered or deemed a

modification or amendment of such warranties.

SolidWorks is a registered trademark of Dassault Systmes

SolidWorks Corp.

SolidWorks 2009 is a product name of SolidWorks

Corporation.

FeatureManager is a jointly owned registered trademark of

Dassault Systmes SolidWorks Corp.

Feature Palette and PhotoWorks are trademarks of

Dassault Systmes SolidWorks Corp.

ACIS is a registered trademark of Spatial Corporation.

FeatureWorks is a registered trademark of Geometric

COMMERCIAL COMPUTER

SOFTWARE - PROPRIETARY

U.S. Government Restricted Rights. Use, duplication, or

disclosure by the government is subject to restrictions as set

forth in FAR 52.227-19 (Commercial Computer Software -

Restricted Rights), DFARS 227.7202 (Commercial

Computer Software and Commercial Computer Software

Documentation), and in the license agreement, as applicable.

Contractor/Manufacturer:

Dassault Systmes SolidWorks Corp., 300 Baker Avenue,

Concord, Massachusetts 01742 USA

Portions of this software are copyrighted by and are theproperty of Electronic Data Systems Corporation or its

subsidiaries, copyright 2009

Portions of this software 1999, 2002-2009 ComponentOne

Portions of this software 1990-2009 D-Cubed Limited.

Portions of this product are distributed under license from

DC Micro Development, Copyright 1994-2009 DC Micro

Development, Inc. All rights reserved.

Portions eHelp Corporation. All Rights Reserved.

Portions of this software 1998-2009 Geometric Software

Solutions Co. Limited.

Portions of this software 1986-2009 mental images GmbH

& Co. KG

Portions of this software 1996-2009 Microsoft

Corporation. All Rights Reserved.

Portions of this software 2009, SIMULOG.

Portions of this software 1995-2009 Spatial Corporation.

Portions of this software 2009, Structural Research &

Analysis Corp.

Portions of this software 1997-2009 Tech Soft America.

Portions of this software 1999-2009 Viewpoint

SolidWors or VMBO en MBOTutorial *+ Tic Tac Toe

$


3/35

Software Solutions Co. Limited.

GLOBEtrotter and FLEXlm are registered trademarks of

Globetrotter Software, Inc.

Other brand or product names are trademarks or registered

trademarks of their respective holders.

Corporation.

Portions of this software 1994-2009, Visual Kinematics,

Inc.

All Rights Reserved.

SolidWors Benelu, developed this tutorial or sel'training with the SolidWors -. /A. progra01 Any other useof this tutorial or parts of it is prohibited. 2or 3uestions4 please contact SolidWors Benelu,1 /ontactinor0ation is printed on the last page o this tutorial1

5nitiative+ 6ees 6loosterboer (SolidWors Benelu,)

"ducational Advisor+ 7ac van den Broe (Vacollege .r1 6nippenberg)

#eali8ation+ Arnoud Breedveld (PA9 /o0puterwors)


-


4/35

TIC-TAC-TOE5n this tutorial we will create a Tic'Tac'Toe ga0e1 The ga0e consists o two plates that are on top o each

other1 5n the top plate4 there are holes or inserting s0all cylinders 0ared :;< or :O% , >% , =%1

$1 Then4 we will 0ae our counter bore holes1

-1 2inally4 we will create a pattern o holes1


?


5/35

1 Start SolidWors and opena new part1

=1 Select the :TopPlane


6/35

" Add a hori8ontal di0ensionto the setch4 as in theillustration on the right1

/hange this di0ension to>%001

Push the @"sc ey on theeyboard to end theco00and1

5 Set the length o thehori8ontal and vertical linesto the sa0e length+

=1 Select a verticalline1

$1 Push the @/trlbutton and clic on ahori8ontal line1

-1 /lic on :"3ual


7/35

' $la%k0eans+ the setch is ully deined1

ou can chec i a setch is ully deined in the status bar at the botto0 othe screen1 5n SolidWors it is not mandatory to 0ae a ully deined setch4but it is a good practice to do this because it can help you to avoid a lot oproble0s when creating a 0odel later1

5n addition to the colors blue and blac4 a line in a setch can turn red oryellow1

' &edor'ello(0eans+ the setch is over'deined1

Try the ollowing+ set the di0ension o the height o the s3uare1 The :Mae.i0ension .rivenC%1The height is deined twice now4 and this creates a conlict in SolidWors1ou 0ust resolve this inconsistency1 5n the 0enu that is shown above4 thebest thing to do is choose :/ancel


8/35

) /lic on :2eatures


9/35

, /lic on :",it Setch1 /lic on O61



10/35

1 Fe,t4 set the di0ension tothe other diagonal line(=*00) and the dia0etero the circle (G&00)1

Push the @"sc ey to

close the S0art .i0ensionco00and1

1! To set an e,act itting tothe hole (G&)4 e,ecute theollowing steps+

=1 Select a di0ension(it turns green)1

$1 Be sure that:ToleranceDPrecision


11/35

1" Mae a hole in this setch+clic on :2eatures


12/35

1* #epeat these steps in thearea na0ed :.irection $


13/35

Fe,t4 clic at the ourcorners o the setch toposition the holes1

/lic on O61

1 The irst part4 the top plate4is now ready1 Save this ileas+ Slab1SJ.P#T1

Tip+ 0ae a new older onyour co0puter irst1 oucan arrange all o the ilesby product1

Work plan We will now create the second part4 the botto0 plate1 We will do this inaccordance with the drawing below1

Fotice that this part loos very 0uch lie the irst one1 The peri0eterdi0ensions and the position o the 0ounting holes are the sa0e1 That iswhy we will create a coniguration ro0 the irst part to produce the second


=-


14/35

one1

/lic on the/onigurationManagertab1

! The na0e o theconiguration is :.eault


15/35

) There are twoconigurations in the listnow+ :Top


16/35

, Select the hole type Tapinthe PropertyManager1

Mae sure all settings aree3ual to the settings in theillustration at right1

/lic on the :Positions


17/35

!1 Whenever no threadpattern appears in theholes4 then change theollowing settings+

=1 /lic the right

0ouse button on:Annotations


18/35

!" #eactivate theconiguration o the topplate1


!5 .ouble'clic on theconiguration :Top


19/35

!+ Open a setch in the Topplane1

.raw a circle4 with thecenter on top o the origin1

Set a di0ension G&1

!, Set the itting to h1

=1 Select thedi0ension1

$1 Set the Tolerancetype to it in thePropertyManager1

-1 Set Shat it to h1

" =1 .rag the height othe e,trusion to $%001

$1 /lic on O61


=


20/35

"1 We will now 0ae anangled edge at the top andat the botto0 o thecylinder with the /ha0erco00and1

/lic on :/ha0er


21/35

"" =1 Type in the capital:;


22/35

"* #otate the 0odel with theFor0al to co00and soyou can get a good view othe setch1

.rag the letter to the centre

o the plane1

"+ /lic on :2eatures< in the/o00andManager andne,t on :",truded /ut


23/35

51 To 0ae the cylinder withthe :O< we will use asecond coniguration1


5 /hange the na0e o thecurrent coniguration(:.eault


24/35

5" Fow4 put a letter :O


25/35

5+ Add the sa0e part again1Place it Iust below the irstone1

5, Fe,t4 we have to changethe coniguration o thebotto0 plate1

=1 /lic with the right

0ouse buttonso0ewhere on thebotto0 plate1

$1 Select :/onigure/o0ponent


26/35

)1 Fe,t4 we have to align thetwo parts with the 0ateco00and1

/lic on :Mate


27/35

)5 Fe,t rotate the 0odel soyou get a good view o thebotto0 o the top part andselect the botto0 plane1

.ouble'clic on O61

)) Fe,t we will put thehe,agon socet headscrews in the 0odel1

=1 Open the .esignJibrary in the TasPane1

$1 /lic on:Toolbo,


28/35

)+ Set the ollowing eaturesin the PropertyManager+

=1 :Si8e


29/35

*1 Place the cylinder or peg inthe asse0bly & ti0es at arando0 position1

Fote that it does not 0atteris you pic an :;< or :O

Solidworks Tutorial 5 Voor Lager en Middelbaar Technisch Onderwijs 2008 English Tws

Documents

Transcript of Solidworks Tutorial 5 Voor Lager en Middelbaar Technisch Onderwijs 2008 English Tws