HANDLEIDING

Schmidt

HT-335

Montagetekening

35

30

33 34 36

1363433

36

3433

29

35 35

45

57

58

44

2217

59

43

47

40

41

4133

3433

61

50

54

51(R)

51(L)

34

34

STAP 1. Montage van de achtersteun 1. Haal de onderdelen uit de verpakking. 2. Plaats de achtersteun (29) tegen de plaat aan de achterzijde van het frame (1) en zet deze vast met twee bouten M8x58 (35),

twee veerringen (34), twee vulringen(33) en twee moeren

M8 (36). 3. Draai de moeren goed vast. STAP 2. Montage van de voorsteun 1. Haal de onderdelen uit de verpakking. 2. Plaats de voorsteun (30) tegen de plaat aan de voorzijde van het frame (1) en zet deze vast met twee bouten (35), twee veerringen (34), twee vulringen(33) en twee moeren M8 (36). 3. Draai de moeren goed vast. STAP 3. Plaatsen van de pedalen 1. Schroef het linker pedaal (51L) in de crank (56) linkse schroefdraad. 2. Schroef het rechter pedaal (51R) in de crank (56) rechtse schroefdraad. 3. Gebruik de sleutel om deze vast te draaien.

1363433

36

3433

29

35 35

2x2x2x2x

35

30

33 34 36

2x2x2x2x

1

51(R)

51(L)

56

STAP 4. Plaatsen van het zadel 1. Verwijder de moeren, veer- en vulringen onder het zadel. 2. Plaats het zadel (45) op de zadelbuis (44) en zet deze vast met de verwijderde drie M8 vulringen (57), M8 veerringen (59) en drie moeren M8 (58).

Plaatsen zadelbuis

1. Draai de stelknop los (43).

2. Schuif de zadelbuis (44) in de buis van het frame.

3. Zet het zadel op de gewenste hoogte.

4. Draai de stelknop (43) vast door de opening van de zadelbuis en

de framebuis (44)

Opmerking: zadelbuis mag niet op de stelknop steunen maar dient door een gat in de buis gevoerd te worden.

44

58

5957

45

43

44

3818

3818

STAP 5. Montage van de stuurpaal 1. Verwijder de M8*20 bout (41), M8*2.0T veerring (34) en de OD20*ID8.5*1.5 vulring (33) van de onderbuis op het frame (40). 2. Zet de weerstandsknop in positie 1 om de weerstandskabel (46) te ontspannen en de montage makkelijker te maken. 3. Houd onderzijde van de stuurpaal (40) dicht bij de bovenzijde van de framebuis. Verbind het computerkabeltje (61) met de onderkabel (22). 4. Verbind de weerstandskabel (46) met de haak (17). 5. Schuif de stuurpaal (40) over de buis van het frame (1). Pas op dat de draad er niet tussen komt en zet deze vast met de verwijderde drie boutjes M8*20 (41), drie M8 veerringen (34) en de drie vulringen (33). Zet ze goed vast. STAP 6. Plaatsen van het stuur 1. Verwijder de boutjes voor uit de stuurpaal (40). 2. Schuif de sensorkabels (D, E) door de opening in de stuurpaal. 3. Plaats het stuur (47) voor tegen de paal (40) en zet deze vast met de verwijderde boutjes

3x 3x 3x

3334

41

22

61

17

46

40

4134

33

47

40

E

D

STAP 7. Plaatsen van de computer 1. Verwijder de twee boutjes M5*10 (54) uit de achterzijde van de computer (50). 2. Verbind de sensorkabels (D, E) en de computerkabel (61) komende vanuit de stuurpaal (40) met de corresponderende kabels uit de computer. 3. Plaats de computer (50) op de stuurpaal (40) en draai de verwijderde boutjes M5*12 (54) er weer in en zet het geheel vast. Afstellen: Stabiliseren van het apparaat Als het apparaat niet vast staat, kunnen door middel van draaien van de eindkappen (31) kleine oneffenheden worden opgevangen zodat het apparaat stabiel staat.

40

C

BA

50

54

61

D

E

31

49

47

40

41

46

41

34

33

35

12

32

30

20

20

43

60 28

4226

27

1

11

1413

15

16

18

17

2138

39

51(L)

36 44

45

24

19

37

51(R)

39

33

34

52

53

55

575958

22

21

31

35

35

31

29

6

5

4

3 9

2

10

87

23

35

48

25

3433

1326

461

65

4

56

63 64

62

50

54

EXPLODED DIAGRAM

Onderdelenlijst

Nr. Naam Aantal Nr. Naam Aantal

1 Frame 1 33 OD20*ID8.5*1.5T gebogen vulring 11

2 Vliegwiel as 1 34 M8*2.0T veerring 11

3 Vliegwiel 1 35 M8*55 schroef 4

4 6000 lager 4 36 M8*1.25*15.5T moer 4

5 Vliegwiel frame plaat 2 37 Rechter afdekking 1

6 M6*50 schroef 2 38 Linker afdekking 1

7 OD16*ID6.5*1.5T vulring 2 39 Crank gat vuller 2

8 M6*1.0*6T borgmoer 2 40 Stuurpaal 1

9 OD14*ID8.5*2.0 vulring 2 41 M8*20 schroef 7

10 M8 borgmoer 2 42 Zadelpaal lagering 1

11 Magneet 1 43 Stelknop 1

12 M10*65 schroef 1 44 Zadelpaal 1

13 OD20*ID10.5*2.0T vulring 3 45 Zadel 1

14 M10*1.5*10T borgmoer 1 46 Boven weerstandskabel 1

15 M5*35 schroef 1 47 Stuur 1

16 M5 moer 2 48 Stuurbekleding 2

17 Onder weerstandskabel 1 49 Eindkappen stuur 2

18 Magneet veer 1 50 Computer 1

19 Riemschijf 1 51 Pedalen 2

20 Lager groep 1 52 Stuurpaal afdichting 1

21 M4*20 kruiskopschroef 3 53 Zadeldek 1

22 Sensor kabel met sensor 1 54 Computer schroef 2

23 M4*20 kruiskopschroef 4 55 Crank 1

24 Riem 1 56 Handpolssensor 2

25 Vereffeningsplaat 1 57 M8 vulring voor zadel 3

26 M10*1.5*6.35T moer 2 58 M8 borgmoer voor zadel 3

27 Riemspannerring 1 59 M8 veerring voor zadel 3

28 Riemspanner veer 1 60 OD14*ID10.5*1.5T 2

29 Achtersteun 1 61 Boven sensorkabel 1

30 Voorsteun 1 62 Handpols schroef 2

31 Achtersteun eindkap 2 63 TCD schroef 1

32 Voorsteun eindkap 2 64 TCD vulring 1

COMPUTER

Functieknop: MODE/RESET knop– Indrukken om functie in te stellen.

– Om tijd, afstand en calorieën te resetten twee seconden ingedrukt houden. 1. SCAN: druk MODE knop als “▼” in SCAN positie is, monitor zal switchen tussen: time、speed、

distance、calories、odometer en pulse, elke aanduiding blijft 6 seconden. 2. TIME : Telt de totaaltijd tussen start en einde. 3. SPEED: Toont werkelijke snelheid. 4. DISTANCE: Toont de afgelegde afstand tussen start en einde. 5. CALORIES: Toont de verbruikte calorien van de oefening van begin tot einde. 6. ODOMETER（TOTAAL AFSTAND）：monitor toont totaal afgelegde afstand.

7. Hartslag: Druk MODE knop als“▼” in Pulse positie is Voor meting van de hartslag, plaats je handpalmen op de sensoren en de monitor laat je hartslag zien in slagen per minuut (BPM) na ca 6-7 sec.

NOTE：

1. Als het display geen symbolen meer toont moeten de batterijen vervangen worden. 2. De monitor zal automatisch uitschakelen als er 4 minuten geen signaal binnenkomt .

3. De monitor zal weer opstarten als oefening hervat wordt

SPECIFICATIES:

FUNCTIE

AUTO SCAN Iedere 6 seconden

TIME 0:00’~99:59’

CURRENT

SPEED 0.0~999.9 KM/H（MILE/H）

DISTANCE 0.00~999.9 KM（MILE）

CALORIES 0.0~999.9 CAL

ODOMETER 0.0~9999 KM（MILE）

PULSE RATE 40~240 BPM (slagen per minuut)

BATTERY TYPE 2 stuks –AAA of UM –4

OPERATING TEMPERATURE 0°C ~ +40°C

OPSLAGTEMPERATUUR -10°C ~ +60°C

USER MANUAL

Schmidt

HT-335

IMPORTANT SAFETY INFORMATION This product has been designed for home use only and built for optimum safety. Please note the following safety precautions: 1. Before starting any exercise program you should consult your doctor to determine if you have any physical or health conditions that could create a risk to your health and safety, or prevent you from using the equipment properly. Your doctor's advice is essential if you are taking medication that affects your heart rate, blood pressure or cholesterol level. This is especially important for persons over the age of 35, pregnant women, or those with pre-existing health problems or balance impairments. 2. Before using this equipment to exercise, always do stretching exercises to properly warm up. 3. Be aware of your body's signals. Incorrect or excessive exercise can damage your health. Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, extreme shortness of breath, feeling light headed, dizzy or nauseous. If you do experience any of these conditions you should consult your doctor before continuing with exercise program. 4. During exercises and after keep children and pets away from the equipment. 5. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. For safety, the equipment should have at least 0.5 meter of free space all around it. Move all sharp objects to. 6. Before each use, visually inspect the unit including hardware and resistance bends. 7. Before using the equipment, check if the nuts, bolts and other bends are securely tightened. 8. Always use the equipment as indicated. If you find any defective components whilst assembling or checking the equipment, or if you hear any unusual noise coming from the equipment while using, stop. Do not use the equipment until the problem has been rectified. 9. Do not insert any object into any openings. 10. Be aware of all regulation and constructions parts which may disturb during exercises. 11. The safety level of the equipment can only be maintained if it is regularly examined for damage and/or wear and tear. 12. Wear suitable clothing whilst using the equipment. Avoid wearing loose clothing which may get caught in the equipment or that may restrict or prevent movement. 13. The equipment has been tested and certified according to EN 957 under class HC. Unit is not intended for commercial use therapy or rehabilitation. 14. Care must be taken when lifting or moving the equipment so as not to injure your back. Always use proper lifting techniques and/or use assistance. 15. The equipment is designed for adult use only. Adults should take care and responsibility for children. 16. Assemble this unit as described in this manual. Use only parts from the set. Check all parts with the part list. WARNING: READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. WE ASSUME NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE CAUSED BY OR THROUGH THE USE OF THIS PRODUCT SPECIFICATIONS Weight: 20kg Flywheel: 4.5 kg Dimensions: 93*56*117cm Maximum weight of user: 100 kg

MAINTENANCE Your unit has been carefully designed to require minimum maintenance. To ensure this, we recommend that you do the following: - Keep your unit clean by wiping sweat, dust or other residue off with a soft, clean cloth after each use - Always make sure that the bands are secure and show no signs of wear - Regularly check the tightness of nuts and bolts SADDLE ADJUSTMENT Loosen seat post knob. Set height according to growth (if you place your heel on the pedal, your leg should be straight). Tighten up the adjustment knob. Do not take out seat post from the main frame. Minimum insertion depth. Insert the saddle post (11) into the tube on the main unit (14) till the minimum insertion depth marking on the saddle post (11) at lease. Secure the saddle post with adjustment knob. TENSION ADJUSTMENT Turn the tension control knob anti-clockwise to reduce the tension, turn the tension control knob clockwise to increase the tension. BREAKING Stop to pedal when you want stop the item. Magnetic bike not acquire breaking system or emergency break.

ASSEMBLY DIAGRAM

35

30

33 34 36

1363433

36

3433

29

35 35

45

57

58

44

2217

59

43

47

40

41

4133

3433

61

50

54

51(R)

51(L)

34

34

STEP 1. ATTACHING THE REAR STABILIZER

1. Loosen and remove all the fixings from the rear stabilizer (29).

2. Attach the rear stabilizer (29) to the arc plate located on the

back side of the main unit (1) and fasten using the fixings

previously removed [two bolts M8x58 (35), two split

washers (34), two washers (33) and two nuts M8 (36)].

3. Use the provided multi-functional spanner to tighten the nuts.

STEP 2. ATTACHING THE FRONT STABILIZER

1. Loosen and remove all the fixings from the front stabilizer (30).

2. Attach the front stabilizer (30) to the arc plate located on the

front side of the main unit (1) and fasten using removed fixings

[two bolts (35), two split washers (34), two washers (33) and

two nuts M8 (36)].

3. Use the multi-functional spanner (provided) to tighten the nuts.

STEP 3. ATTACHING THE PEDALS

1. Screw in the left pedal (51L) on the pedal crank arms (56)

counter-clockwise.

2. Screw in the right pedal (51R) on the pedal crank arms (56)

clockwise.

3. Use the provided multi-functional spanner to tighten the nuts.

1363433

36

3433

29

35 35

2x2x2x2x

35

30

33 34 36

2x2x2x2x

1

51(R)

51(L)

56

STEP 4. ATTACHING THE SADDLE

1. Loosen and remover all the M8 flat, M8 washer and M8 nuts from the saddle.

2. Attach the saddle (45) to the saddle post tube (44) and fasten using the

fixings previously removed [three M8 flat (57), M8 washer (59) and three

pcs M8 nuts(58)].

3. Use the multi-functional spanner (provided) to tighten the nuts.

Assembling the saddle post

1. Loosen the adjustment knob (43).

2. Insert the saddle post (44) in to the tube on the main unit.

3. Adjust the saddle height according to your preference.

4. Guide and screw the adjustment knob (43) through

the opening on the tube and the saddle post (44).

Caution! The saddle post (44) should not directly rest on the adjustment knob (43). Risk of damage and/or

injuries!

44

58

5957

45

43

44

3818

3818

STEP 5. ATTACHING THE FRONT HANDLE POST

1. Remove the fixings [M8*20screw (41), M8*2.0T spring washer (34), OD20*ID8.5*1.5 washer (33)] at the

bottom of the front handle post (40).

2. Set the tension control knob to position 1 to release the tension cable (46) and simplify the procedure.

3. Place the front handle post (40) close to the tube on the main unit (1) and connect the upper computer wire

(61) to the lower computer wire (22).

4. Connect the tension cable (46) to the tension hook (17).

5. Attach the front handle post (40) to the tube on the main unit (1) and fasten using fixing previously removed

[three bolts M8*20 (41), three M8 split washers (34) and three washers(33)].

6. Use the provide allen key to tighten the bolts.

Caution! Make sure not to pinch the computer wire between the tubes. Risk of damage!

STEP 6. ATTACHING THE HANDLE BAR

1. Remove the upper fixings from the front handle post (40).

2. Guide the pulse sensor cables (D, E) through the

opening on the front handle post.

3. Attach the handle bar (47) to the front handle post (40)

and fasten using fixings [two bolts M8*20 (41), two

M8 split washers (34) and two M8 washers (33)].

4. Use the provided allen key to tighten the bolts.

Caution! Make sure not to pinch the pulse wire between

the tubes. Risk of damage!

3x 3x 3x

3334

41

22

61

17

46

40

4134

33

47

40

E

D

STEP 7. ATTACHING THE COMPUTER

1. Loosen the two bolts M5*10 (54) from the backside of the

computer (50).

2. Connect the pulse sensor wires (D, E) and upper computer

wire (61) coming out of the front handle post (40) with the

corresponding cables on the computer.

3. Attach computer (50) to the front handle post (40) and fasten

using two bolts previously removed M5*12 (54).

4. Use the provided multi-functional spanner to tighten the bolts.

Caution! Make sure that none of the wires gets caught in

between two surfaces. Risk of damage!

Adjustment: Stabilizing the bike

If the product is unstable you can reduce or eliminate the tilting by

turning the rear stabilizer caps (31).

40

C

BA

50

54

61

D

E

31

49

47

40

41

46

41

34

33

35

12

32

30

20

20

43

60 28

4226

27

1

11

1413

15

16

18

17

2138

39

51(L)

36 44

45

24

19

37

51(R)

39

33

34

52

53

55

575958

22

21

31

35

35

31

29

6

5

4

3 9

2

10

87

23

35

48

25

3433

1326

461

65

4

56

63 64

62

50

54

EXPLODED DIAGRAM

Parts List

No. Description Qty No. Description Qty

1 Main frame 1 33 OD20*ID8.5*1.5T Arc washer 11

2 Flywheel axle 1 34 M8*2.0T Split washer 11

3 Flywheel 1 35 M8*55 Screw 4

4 6000 Bearing 4 36 M8*1.25*15.5T Nut 4

5 Flywheel plate adaptor 2 37 Right shield 1

6 M6*50 Screw 2 38 Left shield 1

7 OD16*ID6.5*1.5T Washer 2 39 Crank hold cover 2

8 M6*1.0*6T Nylon cap 2 40 Upright 1

9 OD14*ID8.5*2.0 Flat washer 2 41 M8*20 Screw 7

10 M8 Nylon cap 2 42 Seat post bushing 1

11 Magnet 1 43 Seat post knob 1

12 M10*65 Screw 1 44 Saddle post 1

13 OD20*ID10.5*2.0T Washer 3 45 Saddle 1

14 M10*1.5*10T Nylon cap 1 46 TCD upper 1

15 M5*35 Screw 1 47 Handle bar 1

16 M5 Nut 2 48 Handle bar foam 2

17 TCD lower 1 49 Handle bar end cap 2

18 Magnetic spring 1 50 Computer 1

19 Belt plate 1 51 Pedals 2

20 Bearing group 1 52 Lower upright cover 1

21 M4*20 Flat cross screw 3 53 Saddle cover 1

22 Sensor cable lower (with sensor) 1 54 Computer screw 2

23 M4*20 Round cross screw 4 55 Crank 1

24 Belt 1 56 Hand pulse sensor 2

25 Adjust roller plate 1 57 M8 Washer (within saddle) 3

26 M10*1.5*6.35T Nut 2 58 M8 Nylon cap (within saddle) 3

27 Adjust roller gaper 1 59 M8 Split washer (within saddle) 3

28 Adjust roller spring 1 60 OD14*ID10.5*1.5T 2

29 Rear stabilizer 1 61 Sensor wire upper 1

30 Front stabilizer 1 62 Hand pulse screw 2

31 Rear stabilizer end cap 2 63 TCD screw 1

32 Front stabilizer end cap 2 64 TCD washer 1

EXERCISE COMPUTER INSTRUCTION MANUAL

FUNCTIONAL BUTTON:

MODE/RESET – Push down to select functions.

– Push down to reset time、distance and calories for 2 seconds.

FUNCTIONS AND OPERATIONS

1. SCAN: Press MODE button until “▼” appears at SCAN position, monitor will rotate through the following functions:

time、speed、distance、calories、odometer and pulse, each display will be hold 6 seconds.

2. TIME : Count the total time from exercise start to end.

3. SPEED: Display current speed.

4. DISTANCE: Count the distance from exercise start to end.

5. CALORIES: Count the total calories from exercise start to end.

6. ODOMETER（TOTAL DIST）：monitor will display the total accumulated distance.

7. PULSE RATE: Press MODE button until “▼” appears at PULSE position.

Before measuring your pulse rate, please place your palms of your hands on both of your contact pads and the monitor

will show your current heart beat rate in beats per minute(BPM) on the LCD after 6~7 seconds.

Remark: During the process of pulse measurement, because of the contact jamming, the measurement value may be

higher than the virtual pulse rate during the first 2~3 seconds, then will return to normal level. The measurement value

can not be regarded as the basis of medical treatment.

NOTE：

1. If the display is faint or shows no figures ,please replace the batteries.

2. The monitor will automatically shut off if there is no signal received after 4 minutes .

3. The monitor will be auto powered on when starting to exercise push button signal in.

4. The monitor will automatically start calculating when you start to exercise and will stop calculating when you stop

exercising for 4 seconds .

SPECIFICATIONS:

FUNCTION

AUTO SCAN Every 6 seconds

TIME 0:00’~99:59’

CURRENT SPEED 0.0~999.9 KM/H（MILE/H）

TRIP DISTANCE 0.00~999.9 KM（MILE）

CALORIES 0.0~999.9 CAL

ODOMETER 0.0~9999 KM（MILE）

PULSE RATE 40~240 BPM

BATTERY TYPE 2pcs of SIZE –AAA or UM –4

OPERATING TEMPERATURE 0°C ~ +40°C

STORAGE TEMPERATURE -10°C ~ +60°C