Jetstream PDF (2.6) 2005

8/6/2019 Jetstream PDF (2.6) 2005

1/240

JetstreamJetCraft

Users Guide

Release 2.6

Document No. 1000-A2-GB22-10

June 2005
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/

8/6/2019 Jetstream PDF (2.6) 2005

2/240

A June 2005

1000-A2-GB22-10

Copyright 2005 Paradyne Corporation.All rights reserved.Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form orby any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third par ties without the expresswritten permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specificallydisclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporationreserves the right to revise this publication and to make changes from time to time in the contents hereof withoutobligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a newrelease to this manual.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for any help needed. For additionalinformation concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, orParadyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty atwww.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or to speak with a companyrepresentative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

Document FeedbackWe welcome your comments and suggestions about this document. Please mail them to Technical Publications,Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [email protected] . Include thenumber and title of this document in your correspondence. Please include your name and phone number if you arewilling to provide additional clarification.

Trademarks

Acculink, ADSL/R, Bitstorm, Comsphere, DSL the Easy Way, ETC, Etherloop, FrameSaver, GranDSLAM, GrandVIEW,Hotwire, the Hotwire logo, iMarc, Jetstream, MVL, NextEDGE, Net to Net Technologies, OpenLane, Paradyne, theParadyne logo, Paradyne Credit Corp., the Paradyne Credit Corp. logo, Performance Wizard, ReachDSL, StormPort,TruePut are registered trademarks of Paradyne Corporation.

Connect to Success, Hotwire Connected, JetFusion, JetVision, MicroBurst, PacketSurfer, Quick Channel, Reverse

Gateway, Spectrum Manager, and StormTracker are trademarks of Paradyne Corporation.All other products or services mentioned herein are the trademarks, service marks, registered trademarks, orregistered service marks of their respective owners.

8/6/2019 Jetstream PDF (2.6) 2005

3/240

June 2005 B

1000-A2-GB22-10

JetCraft Software License Agreement

CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS. BY USING ANY OF THE JETCRAFTSOFTWARE, YOU AGREE TO BE BOUND BY THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE TOTHESE TERMS AND CONDITIONS, DO NOT USE OR INSTALL ANY OF THE SOFTWARE. IN SUCH EVENT, YOUMAY RETURN THE SOFTWARE TO THE SELLER OR TO PARADYNE (UNUSED) FOR A REFUND OF THE PRICEPAID.

This Software License Agreement (Agreement) grants you certain license rights in connection with the ParadyneCorporation (Paradyne) JetCraft software and related documentation to be installed (the Software).

Where third-party software is pre-installed into Paradyne hardware (Third Party Software) and a separate End UserLicense Agreement (Third Party EULA) is included with the Paradyne hardware, Licensee agrees to comply with theterms and conditions of the Third Party EULA with respect to its use of the Third Party Software.

1. Grant of License

Subject to the terms and conditions of this License, Paradyne hereby grants to Licensee, and Licensee herebyaccepts from Paradyne, a personal, nonexclusive license to install, use and execute Software in machine readableobject code form, on that number and type of stations or access ports for which a licensee fee has been paid,solely for Licensees use in connection with the use of Paradyne hardware or a Paradyne-compatible integratedaccess device (IAD). Licensee shall have the right to make a reasonable number of copies of the Software forbackup purposes. This license shall continue unless and until terminated in accordance with Section 4 of this

Agreement.

2. Proprietary Rights Notices

Licensee agrees (a) to respect all confidentiality notices or legends placed upon the Software; (b) not to concealfrom view any copyright, trademark or confidentiality notices placed on the Software media or on any outputgenerated by the Software; and (c) to reproduce all copyright, trademark or confidentiality notices on all copies ofthe Software, or any portion thereof, made by Licensee as permitted hereunder.

3. Proprietary Rights

Licensee acknowledges that Paradyne (and, as applicable, its licensor(s)) retains exclusive right, title and interestin and to the Software and all copies or portions thereof, including all intellectual property rights. By accepting thislicense, Licensee does not become the owner of the Software, but has the right to use the Software as outlinedand limited in this Agreement. Licensee further acknowledges and agrees that the Software contains confidentialinformation and trade secrets developed and acquired by Paradyne (and, as applicable, its licensor(s)) through the

expenditure of a great deal of time and money. Accordingly, Licensee agrees to treat the Software as confidentialand not to disclose all or any portion of the Software to any third party or entity, except as such disclosure may benecessary to Licensees employees and consultants in the course of their employment. To the extent permitted byapplicable law, Licensee agrees not to modify, decompile, disassemble or otherwise reverse engineer theSoftware. Licensee further agrees not to lend, rent, lease, sublicense or otherwise transfer any copies of theSoftware or any portion thereof in any form to any person, except as permitted in Section 9 of this Agreement.Licensee will use its best efforts and take all reasonable steps to protect the Software and to prevent anyunauthorized reproduction, publication, disclosure, or distribution of the Software or any portion thereof.

4. Term and Termination

This Agreement is effective upon the earlier of (a) the installation of the Software by Licensee (including, but notlimited to, loading the Software on a hard disk), or (b) acceptance of delivery of any Software by Licensee, andshall continue unless and until terminated in accordance with the provisions of this Section 4. This Agreement shallautomatically terminate and Licensee shall lose its license rights hereunder if (i) Licensee transfers possession ofthe Software, any copy of the Software, or any portion or merged portion of the Software to another party, exceptas provided in Section 9, or (ii) violates the provisions of Section 3. Additionally, Paradyne shall be entitled toterminate this Agreement upon written notice to Licensee in the event that Licensee breaches any materialobligation under this Agreement. Licensee shall be entitled to terminate this Agreement upon written notice givenby Licensee to Paradyne. Within ten (10) days after termination of this Agreement, Licensee shall destroy allcopies of the affected Software and related documentation, or any portion thereof, in any form, and shall certifysuch destruction upon the request of Paradyne.

8/6/2019 Jetstream PDF (2.6) 2005

4/240

C June 2005

1000-A2-GB22-10

5. Limited Warranty and Disclaimer of Warranties

The media upon which any Software is contained is warranted to be free from defects in material and workmanshipfor a period of thirty (30) days from the date of delivery to Licensee (the Warranty Period). The entire liability ofParadyne (and, as applicable, its licensor(s)) and Licensees exclusive remedy for breach of the foregoing limitedwarranty shall be for Paradyne to replace any defective media which is returned to Paradyne during the WarrantyPeriod. PARADYNE DOES NOT WARRANT THAT ANY SOFTWARE WILL OPERATE ERROR-FREE, WILL

OPERATE UNINTERRUPTED IN YOUR OPERATING ENVIRONMENT, IS COMPATIBLE WITH ANY SOFTWAREOR HARWARE CONFIGURATION, OR IS FREE OF ERRORS OR BUGS. EXCEPT AS PROVIDED HEREIN,THE SOFTWARE IS PROVIDED AS IS AND PARADYNE MAKES NO WARRANTY, EXPRESS, IMPLIED, ORSTATUTORY, WITH RESPECT TO THE SOFTWARE AND SPECIFICALLY DISCLAIMS THE IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTYOF NON-INFRINGEMENT.

6. Availability of Support

No support (such as ongoing maintenance and delivery of upgrades) is provided for the Software under thisAgreement. Any support for the Software must be purchased separately.

7. Intellectual Property Indemnification

Paradyne shall defend or settle, at its own expense, any action brought against Licensee to the extent arising out ofor based on any claim alleging that the unmodified Software or any portion thereof, as used within the scope of this

Agreement, infringes or misappropriates any third-party rights in copyrights, patents, or trade secrets in the UnitedStates. Additionally, Paradyne shall pay any damages finally awarded against Licensee and attributable to suchclaim, or any costs of settlement to which Paradyne agrees; provided, that (a) Licensee gives prompt written noticeof any such claim, demand, or action to Paradyne; (b) Licensee provides Paradyne with sole control of the defenseand settlement thereof; and (c) Licensee reasonably cooperates with Paradyne in the defense or settlementthereof. In the event that any Software is held in such suit or proceeding to infringe or misappropriate suchintellectual property right, and the use of the Software, or portion thereof, is enjoined, Paradyne shall, at its soleoption and expense (i) procure for Licensee the right to continue using the Software, or portion thereof; (ii) replacethe same with noninfringing programs of reasonably equivalent functionality; or (iii) accept return of the Software,or portion thereof. In the event that Paradyne accepts return of the Software, or portion thereof, Licensee shallreceive a refund of that portion of any fee paid in connection with the license for such Software, or portion thereof.Paradyne assumes no liability hereunder for claims which result from the use or combination of the Software withother than Paradyne hardware or Paradyne-compatible IADs. THIS SECTION 7 SETS FORTH THE ENTIRELIABILITY AND OBLIGATION OF PARADYNE AND LICENSEES SOLE REMEDY FOR ANY CLAIM OFINFRINGEMENT OR MISAPPROPRIATION OF PATENT, COPYRIGHT, TRADE SECRET OR OTHERINTELLECTUAL PROPERTY RIGHTS.

8. Limitation of Liability

IN NO EVENT WILL PARADYNE (OR, AS APPLICABLE, ITS LICENSORS) BE LIABLE TO LICENSEE OR ANYOTHER PARTY FOR ANY CONSEQUENTIAL, INCIDENTAL, PUNITIVE, SPECIAL OR INDIRECT DAMAGESARISING OUT OF THIS AGREEMENT OR THE USE OR INABILITY TO USE THE SOFTWARE, INCLUDING,BUT NOT LIMITED TO, ANY LOST PROFITS OR COST SAVINGS, EVEN IF PARADYNE HAS BEEN ADVISEDOF THE POSSIBILITY OF SUCH DAMAGES.

IN NO EVENT SHALL THE PARADYNE LIABILITY TO LICENSEE, WHETHER BASED ON AN ACTION ORCLAIM IN CONTRACT OR TORT (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE AND, TO THE EXTENTPERMITTED BY LAW, STRICT LIABILITY) OR OTHERWISE, ARISING OUT OF OR RELATED TO THISAGREEMENT EXCEED THE AGGREGATE FEES PAID BY LICENSEE FOR THE SOFTWARE AS OF THE DATESUCH ACTION OR CLAIM WAS FILED.

9. Transfer and Assignment

Neither the licenses granted hereunder nor this Agreement (nor any portion of the Software) may be assigned ortransferred by Licensee except in connection with the sale or transfer of the Paradyne hardware orParadyne-compatible IAD with which the Software is used, and then only if (a) the entire Software and all copiesthereof, and related documentation, are transferred; and (b) the transferee agrees to be bound by the terms of thisAgreement.

8/6/2019 Jetstream PDF (2.6) 2005

5/240

June 2005 D

1000-A2-GB22-10

10. U.S. Government Restricted Rights

The following terms shall apply where Licensee is an agency or unit of the U.S. government.

a. Units of the DoD. Use, duplication or disclosure by the government is subject to restrictions as set forth inparagraph (c)(1)(ii) of the Rights in technical Data and Computer Software clause at DFARS 252.227-7013.Paradyne Corporation, 8546 126th Avenue North, Largo, Florida 33773.

b. Civilian agencies. Use, reproduction or disclosure is subject to restrictions as set forth in subparagraphs (a)through (d) of the Commercial Computer Software-Restricted Rights clause at FARS 52.227-19 and thelimitations set forth in the Paradyne standard commercial agreement for this Software. Unpublished-rightsreserved under the copyright laws of the United States.

11. Compliance with Laws and Payment of Taxes

Licensee agrees to comply with all applicable laws in connection with its license and use of the Software. Licenseerepresents and warrants that it is authorized under applicable United States export laws and regulations to obtainand use the Software licensed hereunder and, and agrees that it will not export or re-export the Software inviolation of those laws and regulations. Licensee shall be responsible for payment of all sales or use taxes, dutiesor other governmental assessments upon the license of the Software to Licensee (exclusive of taxes on the netincome of Paradyne), and any property or other taxes assessed upon Licensees possession or use of theSoftware.

12. Miscellaneous

In the event that any provision of this Agreement is found invalid or unenforceable pursuant to judicial decree ordecision, the remainder of this Agreement shall remain valid and enforceable according to its terms. ThisAgreement shall be construed and enforced in accordance with the laws of the State of Florida, exclusive of itschoice of law rules. The application of the United Nations Convention on the International Sale of Goods isexpressly excluded. Any action or proceeding arising out of or related to this Agreement shall be brought in a stateor federal court of competent jurisdiction located in the County of Pinellas, Florida and both parties hereby submitto the in personam jurisdiction of such courts for purposes of any such action or proceeding. Notwithstanding theforegoing, if Licensee resides outside the United States, any such action or proceeding shall be submitted tobinding arbitration in Pinellas County, Florida, and the arbitration hearing shall be conducted in the Englishlanguage and pursuant to the International Rules of the American Arbitration Association (as then in effect) and

judgment on the award may be entered by any court of appropriate jurisdiction. This Agreement may not bemodified, amended or altered except by a writing signed by a duly authorized representative of Paradyne andLicensee. No waiver of any provision of this Agreement or any right or obligation of either party shall be effectiveexcept pursuant to a writing signed by a duly authorized representative of Paradyne and Licensee. This Agreement

constitutes the entire agreement between Paradyne and Licensee with respect to the transactions contemplatedherein and supersedes any and all prior or contemporaneous oral or written communications with respect to thesubject matter hereof.

8/6/2019 Jetstream PDF (2.6) 2005

6/240

E June 2005

1000-A2-GB22-10

8/6/2019 Jetstream PDF (2.6) 2005

7/240

June 2005 i

Contents

Preface

Audience ..................................................................................viiNew in This Release ...............................................................vii

Organization ............................................................................vii

Related Documents ............................................................... viii

Symbols ...................................................................................... x

Chapter 1 JetCraft Overview

JetCraft Features......................................................................1-2

CPX-1000 Components .......................................................... 1-4

Craft Terminal..........................................................................1-4

Chapter 2 JetCraft Installation

Preparing for JetCraft Installation ........................................ 2-1

Installing JetCraft ...................................................................2-2

Starting JetCraft.......................................................................2-6

Re-connecting to JetCraft ....................................................... 2-9

Where to Go Next ...................................................................2-9

Removing JetCraft...................................................................2-9

Chapter 3 JetCraft Basic Operations
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/

8/6/2019 Jetstream PDF (2.6) 2005

8/240

Table of Contents 1000-A2-GB22-10

ii June 2005

The JetCraft Main Screen ....................................................... 3-1

Menu Bar............................................................................3-2

Toobar Icons.......................................................................3-2

Tree View............................................................................3-3

Map View ...........................................................................3-4

Shelf View...........................................................................3-4

The Alarm Window .......................................................... 3-5

The Status Bar....................................................................3-7

JetCraft Menus.........................................................................3-7

The File Menu....................................................................3-7

The Configuration Menu ................................................. 3-8

The Services Menu............................................................3-9

The Report Menu .............................................................. 3-9

The Help Menu..................................................................3-9

Chapter 4 Administration and User Management

Understanding User Access Control....................................4-1

Changing a User Password ................................................... 4-2

Creating CPX Users ...............................................................4-3Modifying CPX Users ............................................................4-6

Deleting CPX User .................................................................4-8

Reviewing CPX Users.............................................................4-8

Chapter 5 CPX-1000 Configuration

CPX-1000 Configuration Profile ........................................... 5-2

Modifying CPX-1000 Parameters ................................... 5-3Reviewing CPX-1000 Parameters ................................... 5-4

Modifying IP Configuration..................................................5-5

Configuring Global VCI Settings..........................................5-6

Setting CDV Value ..................................................................5-8

Setting LBO Value ...................................................................5-9

8/6/2019 Jetstream PDF (2.6) 2005

9/240

June 2005 iii

1000-A2-GB22-10 Table of Contents

Configuring STS-1 Card.......................................................5-10

Setting Clock Source............................................................. 5-11

Refreshing the CPX-1000 Display ......................................5-13

Chapter 6 Protection Group Provisioning

Assigning Network Protection Group Members ...............6-2

Assigning PSTN Protection Group Members.....................6-5

Swapping Protection Group Members ...............................6-7

Removing Protection Group Members................................6-9

Chapter 7 Interface Groups

Creating T1 Interface Groups ...............................................7-2

Creating STS-1 Interface Group ...........................................7-8

Assigning Ports/Channels to GR-303 Interface Groups 7-12

Removing Ports/Channels from GR-303 Interface Groups 7-16

Assigning Ports/Channels to the T1 CAS Interface Group 7-18

Removing Ports/Channels from the T1 CAS Interface Group7-21

Modifying GR-303 Interface Groups..................................7-23

Deleting GR-303 Interface Groups......................................7-25

Switching Over......................................................................7-26

Performing an EOC Switchover....................................7-27

Performing a TMC Switchover ..................................... 7-29

Configuring PPS Settings...............................................7-31

Chapter 8 Network Resource Manager

Overview..................................................................................8-1

Provisioning.............................................................................8-2

Modifying a Network Resource......................................8-3

8/6/2019 Jetstream PDF (2.6) 2005

10/240


iv June 2005

Deleting a Network Resource ......................................... 8-4

Chapter 9 IAD Profiles and IADs ProvisioningIAD Profiles..............................................................................9-1

Adding IAD Profiles ..............................................................9-2

Modifying IAD Profiles..........................................................9-3

Deleting IAD Profiles .............................................................9-5

IADs .......................................................................................... 9-6

IAD Admin States...................................................................9-7

Creating IADs..........................................................................9-9

Creating Voiceband IADs Using the Wizard ................9-9Creating LES CAS Loop Start/Ground Start IADs Usingthe Wizard........................................................................9-17

Creating LES CAS E&M IADs Using the Wizard.......9-21

Creating LES CAS Mixed Port IADs Using the Wizard 9-24

Creating a Voiceband IAD Using the Create Command9-28

Creating a LES CAS Loop Start/Ground Start IAD Using

the Create Command......................................................9-32Creating a LES CAS E&M IAD Using the CreateCommand.........................................................................9-36

Creating a LES CAS Mixed Port IAD Using the CreateCommand.........................................................................9-40

Modifying IADs ....................................................................9-44

Deleting IADs ........................................................................9-47

Reviewing IADs ....................................................................9-49

Searching IADs by Fields ....................................................9-49

Chapter 10 Alarms, Events, and Statistics

Alarms Notification .............................................................. 10-1

CPX Alarms ...........................................................................10-3

Setting Alarm Polling Interval ............................................ 10-3

8/6/2019 Jetstream PDF (2.6) 2005

11/240

June 2005 v

1000-A2-GB22-10 Table of Contents

Statistics..................................................................................10-4

Statistics Summary................................................................10-6

Polling CP Performance.....................................................10-10

Accessing Interface Groups............................................... 10-11

Accessing Network Protection Groups............................10-12

Accessing PSTN Protection Groups ................................. 10-13

Accessing STS-1 Port .......................................................... 10-14

Accessing DS-1 Port............................................................10-14

Accessing IADs ...................................................................10-16

Graphing Statistics..............................................................10-17

Chapter 11 Maintenance and Services

Backing Up CPX-1000 Database ......................................... 11-2

Restoring CPX-1000 Database............................................. 11-3

Rebooting the CPX-1000 ..................................................... 11-4

Rebooting the MP or CP Card............................................. 11-5

Setting the Clock ................................................................... 11-5

Switching CP Cards.............................................................. 11-7

Ensuring Redundancy ................................................... 11-8Changing CP Card States............................................... 11-9

Performing a CP Switchover....................................... 11-11

Hot Swapping...................................................................... 11-11

Hot Swapping MP Card .............................................. 11-12

Hot Swapping CP and HSC Cards ............................ 11-13

Hot Swapping Line Cards ........................................... 11-14

Performing Loop Back Test................................................ 11-15

Tracing STS-1 Path .............................................................. 11-17Downloading IAD Software.............................................. 11-18

Automated IAD Software Download .............................. 11-20

Configuring the IAD Auto Download Profiles ........ 11-22

Add ..................................................................... 11-24

Modify ................................................................ 11-24

8/6/2019 Jetstream PDF (2.6) 2005

12/240


vi June 2005

Delete .................................................................. 11-25

Close.................................................................... 11-26

Remote Restarting of IADs................................................ 11-27

Chapter 12 Integrated Monitoring

Launching Integrated Monitor............................................12-2

Interpreting Integrated Monitor Data................................12-3

Refreshing Integrated Monitoring......................................12-5

Appendix AJetCraft Menu Map

Appendix B Statistics Definitions

Appendix C Alarm Summary

Index

8/6/2019 Jetstream PDF (2.6) 2005

13/240

June 2005 vii

Preface

TheJetCraft Users Guide provides detailed instructions for

installing Paradyne Jetstream craft interface terminal software on

your PC. This guide also provides instructions to configure and

provision a CPX-1000 Voice Services Platform using JetCraft.

Audience TheJetCraft Users Guide is written for test and installationtechnicians and engineers who install and use the JetCraft software

to test a CPX-1000.

New in ThisRelease

Release 2.6 of JetVision includes the following enhancements:

T1-CAS Interface Group

LES CAS IAD E&M Wink Start Signaling

Organization TheJetCraft Users Guide is organized as follows: Chapter 1, JetCraft Overview, provides an overview of the

CPX-1000 Voice Gateway and defines the hardware and

software components and their functions. It also explains

the role JetCraft plays in the initial setup of CPX-1000

equipment and its ongoing management.

Chapter 2,JetCraft Installation, provides instructions forinstalling and removing JetCraft.

Chapter 3, JetCraft Basic Operations, describes component

icons in the main window, and how to use them.

Chapter 4, Administration and User Management, provides

procedures provisioning CPX-1000 users.

8/6/2019 Jetstream PDF (2.6) 2005

14/240

Preface 1000-A2-GB22-10

viii June 2005

Chapter 5, CPX-1000 Configuration, provides procedures to

configure CPX-1000 and create users and CPX-1000 profiles.

Chapter 6, Protection Group Provisioning, provides

instructions to provision the network and PSTN Protection

Group.

Chapter 7, Interface Groups, provides instructions to

provision the T1 and STS-1 Interface Groups.

Chapter 9, IAD Profiles and IADs Provisioning, provides

instructions to provision IAD Profiles and IADs.

Chapter 10, Alarms, Events, and Statistics, describes JetCraft

alarms and how to collect and graph error and performance

statistics.

Chapter 11, Maintenance and Services, provides instructions

to perform routine maintenance.

Chapter 12, Integrated Monitoring, provides instructions to

launch the Integrated Monitor and interpret the operational

status of each entity it monitors.

Appendix A,JetCraft Menu Map, provides a linear,

hierarchical overview of the tasks and sub-tasks associated

with the JetCraft main window menu.

Appendix B, Statistics Definitions, provides definitions for

statistics used in JetCraft.

Appendix C, Alarm Summary, provides a summary of

events and error alarms.

Index

RelatedDocuments

Complete documentation for this product is available online at

www.paradyne.com. Select Support Technical Manuals

Jetstream Media Gateway Systems.

CPX-1000 Voice Services Platform Installation and Operation

Describes features and characteristics of the CPX-1000

equipment, provides procedures to install the equipment,and provides instructions to troubleshoot and repair the

CPX-1000.

JetVision Installation

Describes how to install JetVision on Windows and Solaris

platforms.

JetVision User s Guide
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://www.paradyne.com/tech_support/jetstream_manuals.htmlhttp://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://www.paradyne.com/tech_support/jetstream_manuals.html

8/6/2019 Jetstream PDF (2.6) 2005

15/240

June 2005 ix

1000-A2-GB22-10 Preface

Describes the top level management of multiple CPX-1000

equipment.

To order a paper copy of a Paradyne document or to talk to a sales

representative, please call 727-530-2000.

8/6/2019 Jetstream PDF (2.6) 2005

16/240

Preface 1000-A2-GB22-10

x June 2005

Symbols This document uses the following special symbol.

Voice/Data InterruptionThis telephone symbol alerts you to the procedures thatinterrupt traffic.

Note

Throughout this guide, the pointing finger highlightsimportant information. Be sure to read this informationbefore continuing.

Tip

This symbols points out helpful information whenperforming procedures.

8/6/2019 Jetstream PDF (2.6) 2005

17/240

June 2005 1-1

C H A P T E R 1

JetCraft Overview

JetCraft is primarily used by the central office craft personnel

performing on-site management, including the installation and

troubleshooting of CPX-1000 shelves. This chapter explains the

role JetCraft plays in the initial setup of a CPX-1000 equipment and

its ongoing management. This chapter includes these topics:

JetCraft features (page 1-2)

CPX-1000 components (page 1-4)

Craft terminal (page 1-4)

A Java application, JetCraft uses a Graphical User Interface (GUI)

to manage the CPX-1000 and its components, including

configuring the CPX-1000 shelves

provisioning Interface Groups, and Protection Groups, and

IADs monitoring performance

reporting alarms

troubleshooting and maintenance

JetCraft also provides a security feature for controlling user access

to the CPX-1000.

8/6/2019 Jetstream PDF (2.6) 2005

18/240

1. JetCraft Overview 1000-A2-GB22-10

1-2 June 2005

JetCraftFeatures

Table 11 lists the JetCraft features.

Table 11. JetCraft Features

Features Description

Configuration At startup, CPX-1000 automatically discovers the following linecards:

TDM 12T-1

ATM (OC-3 and DS-3)

STS-1

For redundancy, the CPX-1000 supports primary/secondaryand active/standby states for the following cards:

Call Processors (CP)

ATM (OC-3, DS-3)

STS-1

Besides BITS clock and multiple VPI/VCI settings,JetCraft alsosupports Cell Delay Variation (CDV) for Frame Relay and ATMprotocols and Line Build Out (LBO).

Provisioning

Interface Groups for T1and STS-1

JetCraft supports RT provisioning and up to eight IGs can beprovisioned.

JetCraft enables PPS settings and allows switchover on selectedEOC and TMC.

Protection Groups forPSTN and ATM

A Protection Group provides a logical mapping for two ports,where only one port is active at a time and another port is in astandby state. Up to six PSTN and four ATM PGs can beprovisioned. JetCraft also supports ATM APS configuration.

IAD Profiles JetCraft provides a variety of default profiles.

IADs JetCraft supports RT provisioning and up to 8,192 IADs can beprovisioned.

Besides dynamic compression, JetCraft also supports a null (0)Call Reference Value (CRV). This feature allows for a moreeffective use of the CRV IAD assignments when less than a fullset of ports are required to be provisioned for the IAD.

8/6/2019 Jetstream PDF (2.6) 2005

19/240

June 2005 1-3

1000-A2-GB22-10 1. JetCraft Overview

Performance monitoring JetCraft includes performance monitoring tools for routinemaintenance and network capacity planning. When initiated,JetCraft collects information on equipment performance, such astotal calls active on a CPX-1000 and virtual circuit bandwidthusage.

Alarms reporting JetCraft includes an alarm sequence ID and a customizablealarm polling interval.

Troubleshooting andmaintenance

Switchover: JetCraft allows you to initiate a switchover, wheretwo redundant cards exchange their active/standby states.

Hot swap: JetCraft allows you to hot swap (planned or

unplanned) a card on module without affecting the operation ofthe CPX-1000.

Loop back: JetCraft provides a diagnostics tool to test theinbound traffic.

Database backup and restore: the service provider can createCPX-1000 provisioning database files, use a File TransferProtocol (FTP) application to transmit and receive theprovisioning database files to and from a CPX-1000, and thenrestore the CPX-1000 provisioning database using theappropriate JetCraft menu option.

In addition, you can maintain and upgrade the software for

associated IADs through the JetCraft interface.

Integrated Monitor A diagnostic tool to provide an a real-time view of the health ofa CPX-1000 and its associated managed domain.

Security JetCraft provides a default user ID (cpxuser) and password

(cpxuser) and uses three user groups to control access to the

CPX-1000.

Table 11. JetCraft Features (Continued)

Features Description

8/6/2019 Jetstream PDF (2.6) 2005

20/240

1. JetCraft Overview 1000-A2-GB22-10

1-4 June 2005

CPX-1000Components

Table 12 lists and describes the icons used in JetCraft.

Craft Terminal The JetCraft software runs on Windows 98/2000 or NT 4.0. A PC(or laptop) with the JetCraft software installed serves as a Craft

terminal to the CPX-1000.

The Craft terminal communicates with a CPX-1000 through an

Ethernet connection using TCP/IP protocol. The physical

connection can be local (through a Local Area Network (LAN)connection) or remote (through a Wide Area Network (WAN)

connection).

Table 12. Components Represented as Icons in JetCraft

Icons Description

CPX-1000 icon: the fundamental unit of installation. JetCraftaccesses one CPX-1000 at a time.

Shelf icon: up to 16 cards are installed in a CPX-1000 shelf.

Card icon: each card has configuration and status information.

Port icon: The physical ports on a card.

Protection Group (PG) manager icon: selects a PG for multiplenetwork (PSTN and ATM) PG assignments, unassignments, andmodification.

TDM Manager icon: selects for multiple Interface Group (IG)creation, deletion and modification.

IAD icon: IADs are uniquely associated with a CPX-1000. Youcreate voice path ATM Permanent Virtual Circuits (PVCs) whenyou create the IADs.

8/6/2019 Jetstream PDF (2.6) 2005

21/240

June 2005 2-1

C H A P T E R 2

JetCraft Installation

This chapter provides instructions for installing JetCraft.

Preparing the environment for installation (page 2-1)

Installing JetCraft (page 2-2)

Removing JetCraft (page 2-9)

Preparing forJetCraftInstallation

Before installation, make sure that the person performing the

installation has administrator privileges.

JetCraft requires the following:

Workstation running Windows 98/2000 and NT Version 4,

Service Pack 5 or later

Netscape Navigator, Release 4, or later or Internet Explorer,

Release 4.0.1, or later

Table 21lists the hardware requirements for running JetCraft.

Table 21. Hardware Requirements for JetCraft

Hardware Requirements

Craft Terminal Pentium class 233 MHzprocessor or greater

RAM 128 MB

Virtual memory 256 MB

Storage (hard disk) 100 MB free disk space

CD-ROM drive Accessible

Network Ethernet NIC

8/6/2019 Jetstream PDF (2.6) 2005

22/240

2. JetCraft Installation 1000-A2-GB22-10

2-2 June 2005

InstallingJetCraft

Though two different versions of JetCraft can co-exist on the same

machine, we recommend that they be installed in different folders.

To install the JetCraft software:

Step 1 Place the JetCraft application software CD into the CD-ROM drive.

A screen appears, indicating the file extraction status. Then the

Welcome screen appears (Figure 21).

Figure 21. Welcome Screen

Monitor 640 x 480 (VGA) or larger resolution preferredMouse and keyboard

Table 21. Hardware Requirements for JetCraft (Continued)

Hardware Requirements

8/6/2019 Jetstream PDF (2.6) 2005

23/240

June 2005 2-3

1000-A2-GB22-10 2. JetCraft Installation

Step 2 Click Next. The License Agreement screen appears (Figure 22).

Figure 22. Software Agreement License Screen

Click here to continue

Note

At any time during this installation, you can click theBack button to review or correct the previous settings,then proceed from that point forward.

8/6/2019 Jetstream PDF (2.6) 2005

24/240


2-4 June 2005

Step 3 Click to select the accept the terms of the license

agreement checkbox, then click Next. The Destination Folder

screen appears (Figure 23).

Figure 23. Destination Folder Screen

Step 4 Click Next to accept the default path: C:\Jetstream\.

Or

Type the directory path in the Destination folder field or

click Change to navigate to where JetCraft will be installed. Then

click Next.

If a folder for JetCraft does not exist, a dialog box appears, asking if

you want to create one. Click Yes.

The Feature Selection screen appears, listing the installed features

and their file sizes (Figure 24).

8/6/2019 Jetstream PDF (2.6) 2005

25/240

June 2005 2-5


Figure 24. Feature Selection Screen

Step 5 Click Next. The Ready to Install screen appears, listing the

features to be installed (Figure 25).

Figure 25. Ready to Install Screen

Note

Make sure that both the Visibroker and JetCraftcheckboxes are selected.

8/6/2019 Jetstream PDF (2.6) 2005

26/240


2-6 June 2005

Step 6 Click Install Now. A screen appears, showing the file extraction

progress. After the files are extracted, the Installation Summary

screen appears, listing the installed applications and their file sizes

(Figure 26).

Figure 26. Installation Summary Screen

Step 7 Click Exit. The JetCraft icon (Figure 27) appears on your

desktop.

Figure 27. JetCraft Icon

StartingJetCraft

JetCraft Release 2.6 is not backward compatible. If you log in to a

CPX-1000 running an earlier version, an error message appears,

indicating the version of the CPX-1000 is unsupported.

Once connected, JetCraft pings the CPX-1000 on a repeatinginterval and notifies you when the connection is lost

(Re-connecting to JetCraft on page 2-9).

The CPX-1000 is shipped with the following defaults set:

IP address: 10.0.10.100

subnet mask: 255.255.255.0

8/6/2019 Jetstream PDF (2.6) 2005

27/240

June 2005 2-7


To start the JetCraft application:

Step 1 Change the IP address of the craft terminal to match that of

CPX-1000 (Network Neighborhood > TCP/IP tab), but increase the

last digit by one bit. For example, if the IP address of the CPX-1000

is 10.153.145.128, then enter 10.153.145.128.

Step 2 Change the subnet mask of the craft terminal to match that of

CPX-1000.

Step 3 Reboot and restart the craft terminal.

Step 4 Double-click the JetCraft icon on your desktop. The Login dialog

box appears, displaying the default IP address (Figure 28).

Figure 28. JetCraft Login Dialog Box

Step 5 Type the IP address of the CPX-1000 to which you are logging in

the CPX IP field.

Step 6 Type cpxuser(default user ID) in the User Id field.

Step 7 Type cpxuser(default password) in the Password field.

Note

Ensure that the craft terminal (PC) and CPX-1000 are on

the same subnet.

NoteOnce the IP address is entered, you dont have to type itagain until you change the CPX-1000 IP address. Youcan use the drop-down list to select the IP addresses.
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://-/?-http://-/?-http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/

8/6/2019 Jetstream PDF (2.6) 2005

28/240


2-8 June 2005

Step 8 Click OK.

If the login fails, a message appears, describing the failure as

shown in Figure 29. Click Cancel to exit the login dialog

box. Resolve the login problems, then repeat Step 1 to log inagain.

Figure 29. Login Fail

When the login is successful, the JetCraft Main screen

similar to Figure 210 appears.

Figure 210. JetCraft Main Screen

Login Failure message
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://-/?-http://-/?-http://-/?-http://-/?-http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/

8/6/2019 Jetstream PDF (2.6) 2005

29/240

June 2005 2-9


Re-connectingto JetCraft

JetCraft automatically times out after a period of inactivity. When

the connection is lost, the following dialog box appears:

Click Re-login. Then type your user ID and password in their

respective fields when the JetCraft Login window reappears.

Where to GoNextYou can learn about working with the JetCraft Main window(Chapter 3, JetCraft Basic Operations), or see an overview of all the

menu options on the JetCraft Main window (Appendix A,JetCraft

Menu Map).

You can also use the JetCraft Main screen to configure the

CPX-1000 shelf in the following order:

Configuring CPX-1000 (see Chapter 5, CPX-1000

Configuration) or creating user access (see Chapter 4,

Administration and User Management)

Provisioning Protection Groups (Chapter 6, Protection

Group Provisioning) Provisioning Interface Groups (Chapter 7, Interface Groups)

Provisioning IAD Profiles and ISDN Port Templates

(Chapter 9, IAD Profiles and IADs Provisioning)

Provisioning IADs (Chapter 10, Alarms, Events, and

Statistics)

RemovingJetCraft

To remove an earlier version of JetCraft:

Step 1 Click the Start button > Settings > Control Panel.

Step 2 Double-click Add/Remove Programs. The Add/Remove

Programs Properties screen appears.

8/6/2019 Jetstream PDF (2.6) 2005

30/240


2-10 June 2005

Step 3 Select the JetCraft applications files, click Add/Remove as shown

in Figure 211. A dialog box appears, asking if you want to delete

the selected item.

Figure 211. Add/Remove Programs Properties Screen

Step 4 Click Yes. The Uninstallation Welcome screen appears

(Figure 212).

Figure 212. Uninstallation Welcome Screen
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://-/?-http://-/?-http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://-/?-http://-/?-

8/6/2019 Jetstream PDF (2.6) 2005

31/240

June 2005 2-11


Step 5 Click Next. The Feature Selection screen appears (Figure 213).

Figure 213. Feature Selection Screen

Step 6 Select the items you want to delete, then click Next. The Ready to

Uninstall screen appears, listing the items to be deleted

(Figure 214).

Figure 214. Ready to Uninstall Screen
http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://-/?-http://-/?-http://jc%20user_xref.pdf/http://jc%20user_xref.pdf/http://-/?-http://-/?-

8/6/2019 Jetstream PDF (2.6) 2005

32/240


2-12 June 2005

Step 7 Click Uninstall Now. The Uninstallation Summary screen

appears (Figure 215) after the selected items are deleted.

Figure 215. Uninstallation Summary Screen

Step 8 Click Exit. You are returned to the desktop.

Step 9 Close the Add/Remove Programs Properties screen.

8/6/2019 Jetstream PDF (2.6) 2005

33/240

June 2005 3-1

C H A P T E R 3

JetCraft Basic Operations

This chapter describes the JetCraft Main screen and different views

from which it displays and menus. This chapter includes the

following topics:

The JetCraft Main screen (page 3-1) The JetCraft menus (page 3-7)

The JetCraftMain Screen

The JetCraft Main screen is an iconic representation of the

CPX-1000 components it manages and the network entities with

which it interfaces. The Main screen is divided into six sections

(Figure 31):

Menu bar

Toolbar icons

Tree View

Map View (changes to Shelf View when the Shelf icon is

selected)

Alarm window

Status bar

You can access commands from the menu bar, toolbar icons, and

by right-clicking objects in the Tree and Map views.For a complete

listing of options available for each menu and icons, refer to

Appendix A,JetCraft Menu Map.

8/6/2019 Jetstream PDF (2.6) 2005

34/240

3. JetCraft Basic Operations 1000-A2-GB22-10

3-2 June 2005

Figure 31. JetCraft Main Screen

Menu Bar To use the JetCraft menus to perform an operation, make surethat you have access to this operation and that you have selected

an appropriate CPX-1000 managed object for the operation. Ifyour access to the operation is restricted, that menu selection is

grayed out.

Toobar Icons There are six icons on the toolbar (Figure 32). You can click anicon on the toolbar to open the menu selections (except the Alarm

Summary icon).

Figure 32. Toolbar Icons

Click here to create STS-1 IGs

Click here to create an IAD

Click here to create an IAD Profile Click here to update alarm summary

Click here to create T1 IGs

Click here to perform IAD

management functions

8/6/2019 Jetstream PDF (2.6) 2005

35/240

June 2005 3-3

1000-A2-GB22-10 3. JetCraft Basic Operations

Tree View The Tree View (Figure 33) provides a hierarchal view of theCPX-1000 cards. A plus sign (+) next to the card name indicates

that there are ports assigned to that card. The name of the card

includes the slot number and the name and number of the port. For

example, the card labeled 03-TDM-12T1 indicates that slot 3contains a TDM T1 card.

To expand and view the structure of the CPX-1000 cards, either

double-click the Shelf icon on the Tree View or click the plus (+)

key next to that icon. Click the minus () key to collapse the list.

You can use the Tree View to find specific shelf or alarm

information. Right-click an element icon and choose to view

information about that element.

Figure 33. Tree View

CPX-1000

Shelf

Card

Port

Network Protection Group

PSTN Protection Group

Interface Group

IAD

8/6/2019 Jetstream PDF (2.6) 2005

36/240


3-4 June 2005

Map View Use the Map View (Figure 34) to select and view configuration,performance, and alarm information about the CPX-1000 and

IADs. Right-click an element and choose configuration or report

information.

The Map View shows all Local Digital Switch (LDS, up to four).

You can use the Refresh CPX feature to update the Map View as

the LDS are added or deleted.

Figure 34. Map View

Shelf View Clicking the Shelf icon in the Tree View changes the Map View toShelf View, displaying the cards installed on your CPX-1000. Use

the Shelf View (Figure 35) to select and view configuration,

performance, and alarm information about the CPX-1000 cards.

Right-click a card and choose card configuration or report

information. When Shelf View appears, resize the window to viewthe card names at the bottom of the window.

The color shown indicates the states of the cards: green for active

and blue for standby. When in transitional mode (e.g., during

switchover), the card is shown in wheat color. Table 31

describes the types of cards that are currently available and lists

their slots assignment.

For a description of individual cards, refer to CPX-1000 Voice

Services Platform Installation and Operation.

8/6/2019 Jetstream PDF (2.6) 2005

37/240

June 2005 3-5


Figure 35. Shelf View

The AlarmWindow

Alarms appear in the current alarm summary window as shown in

Figure 36. Update the current alarm summary by clicking on

the toolbar.

Table 31. CPX-1000 Cards

Card Type Abbreviation Valid Slot Assignment

Call Processing, primary (A) orsecondary (B)

CP-A

CP-B

7

9

Hot Swap Controller (bridge),primary (A) or secondary (B)

HSC-A

HSC-B

10

8

Management Processing MP 6

ATM-OC3 OC3 Slots 15 and 1116

ATM-DS3 DS3 Slots 15 and 1116

TDM-T1 TDM-12 Slots 15 and 1116

Synchronous transport signal-1 STS-1 Slots 15 and 1116

8/6/2019 Jetstream PDF (2.6) 2005

38/240


3-6 June 2005

You can sort and view alarm information by clicking any one of the

Alarm window column headings. Click another column heading

to change the sort order again.

Figure 36. Alarm Window

Alarmed elements appear in the Tree View and Map View in acolor relating to their alarm severity (Table 32). Alarms are also

indicated by a large X on the affected object in the Tree View. The

color of the X indicates the severity of the alarm (Chapter 10,

Alarms, Events, and Statistics).

Table 32. Alarm Severity by Color

Alarm Severity Color

Critical redMajor orange

Minor yellow

Indeterminate blue

Unknown cyan

8/6/2019 Jetstream PDF (2.6) 2005

39/240

June 2005 3-7


The Status Bar The status bar displays alarm events and messages (Figure 37).Two colors indicate the type of message: blue for status and red for

error.

Refer to Chapter 10, Alarms, Events, and Statistics for messagedefinitions.

Figure 37. Status Bar

JetCraft Menus Four menus provide JetCraft operations: File menu

Configuration menu

Services menu

Report menu

The Help menu provides a quick look-up of JetCraft procedures. It

also provides an easy and convenient way to view information

about JetCraft.

The File Menu Use the File menu to:

refresh the CPX-1000 display after change

exit JetCraft

Displayed messageCPX-1000 IP

User ID

8/6/2019 Jetstream PDF (2.6) 2005

40/240


3-8 June 2005

TheConfigurationMenu

Operations displayed in the Configuration menu and icons

selected in the Tree View are mutually inclusive; that is, an icon

needs to be selected before the operation becomes available.

Use the Configurationmenu to: configure CPX cards and ports (Chapter 5, CPX-1000

Configuration)

perform CP, MP, and line cards switchover (Chapter 11,

Maintenance and Services)

create and manage Interface Group (Chapter 7, Interface

Groups)

poll DS1 error statistics (Chapter 10, Alarms, Events, and

Statistics)

perform EOC/TMC switchover (Chapter 7, Interface

Groups)

configure PPS settings (Chapter 7, Interface Groups)

swap between the primary and secondary members of the

Protection Group (Chapter 6, Protection Group

Provisioning)

perform a STS-1 path trace (Chapter 11, Maintenance and

Services)

create and manage IAD profiles (Chapter 9, IAD Profiles

and IADs Provisioning)

create and manage IADs (Chapter 9, IAD Profiles and IADsProvisioning)

launch Integrated Monitor (Chapter 12, Integrated

Monitoring)

synchronize BITS clock (Chapter 5, CPX-1000

Configuration)

configure LBO values (Chapter 5, CPX-1000 Configuration)

poll CP performance statistics (Chapter 10, Alarms, Events,

and Statistics)

8/6/2019 Jetstream PDF (2.6) 2005

41/240

June 2005 3-9


The ServicesMenu

Use the Services menu to:

back up and restore the CPX-1000 configuration

(Chapter 11, Maintenance and Services)

set the alarm polling interval (Chapter 10, Alarms, Events,and Statistics)

set up the VCI value (Chapter 5, CPX-1000 Configuration)

configure the CPX IP address (Chapter 5, CPX-1000

Configuration)

change the CPX time (Chapter 11, Maintenance and

Services)

reboot the CPX-1000 (Chapter 11, Maintenance and

Services)

create a CPX user profile (Chapter 4, Administration andUser Management)

change password (Chapter 4, Administration and User

Management)

The Report Menu Use the Report menu to generate:

error graph statistics (Chapter 10, Alarms, Events, and

Statistics)

performance graph statistics (Chapter 10, Alarms, Events,

and Statistics)

The Help Menu Use the Help menu to:

launch the JetCraft Help

view information about JetCraft

8/6/2019 Jetstream PDF (2.6) 2005

42/240


3-10 June 2005

8/6/2019 Jetstream PDF (2.6) 2005

43/240

June 2005 4-1

C H A P T E R 4

Administration and UserManagement

This chapter provides instructions for provisioning users. These

tasks include:

Understanding user access control (page 4-1)

Changing user passwords (page 4-2)

Creating CPX users (page 4-3)

Although you can install JetCraft anytime, typically, you install the

CPX-1000 and then the JetCraft software. After installation, use

JetCraft to configure users and assign their access privileges. These

users can access the CPX-1000 and create Interface Groups and

IADs.

UnderstandingUser AccessControl

When you first start JetCraft, log in using the default user ID(cpxuser) and password (cpxuser). The default user ID belongs to an

authorized user group that has access to all CPX operations. To

limit CPX-1000 access, we recommend changing the default

password as soon as possible.

Each user group has a specific level of access and privilege, and

users belonging to a specific group can only perform operations

that are assigned to that group. Each user is given a password

when the user group is created. Table 41 lists and defines the user

access levels and their privileges.

8/6/2019 Jetstream PDF (2.6) 2005

44/240

4. Administration and User Management 1000-A2-GB22-10

4-2 June 2005

Changing aUser Password

To change your own password or to change another user s

password (if you have Admin privileges):

Step 1 Select Change CPX Password from the Services menu. The

Change Password window appears (Figure 41).

Figure 41. Change Password Window

Step 2 Type the old and new password.Step 3 Type the new password again.

Step 4 Click OK to change the password.

Table 41. User Access Level Summary

Access Level Privilege

Admin This group has full access to all features of JetCraft, including changing otherusers passwords. They can create, modify, and delete all users, and canchange JetCraft configuration.

Operations This group can access JetCraft configuration but cannot create, modify, ordelete all users. They can change their own password but not others.

Reports This group can only view reports and statistics but cannot make or save anychanges.

8/6/2019 Jetstream PDF (2.6) 2005

45/240

June 2005 4-3

1000-A2-GB22-10 4. Administration and User Management

Creating CPXUsers

To create a CPX user:

Step 1 Select Create CPX User from the Services menu. The CreateUser window appears (Figure 42).

Figure 42. Create User Window

Step 2 Enter the following information (up to 32 alphanumeric characters

including spaces and punctuation) in their respective fields:

IDusers login ID

Nameusers name

Passwordusers password

Retypethe users password

Expiration Datedefault is set to 10 years from the date

when this user is created (required Admin privilege to

modify)

Groupselect Admin, Operations, or Reports from the

drop-down list

Note

The Address, Contact, and Comment tabs are optional.

8/6/2019 Jetstream PDF (2.6) 2005

46/240


4-4 June 2005

Step 3 Click Address. The Address page appears (Figure 43).

Figure 43. Create User WindowAddress Tab

Step 4 Enter the address in their respective fields (up to 32 alphanumeric

characters including spaces and punctuation).

Step 5 Select Contact. The Contact page appears (Figure 44).

Figure 44. Create User WindowContact Tab

8/6/2019 Jetstream PDF (2.6) 2005

47/240

June 2005 4-5


Step 6 Enter the phone number, pager, and Email in their respective fields

(up to 32 alphanumeric characters including spaces and

punctuation).

Step 7 Select Comments. The Comment page appears (Figure 45).

Figure 45. Create User WindowComment Tab

Step 8 Click anywhere in the Comment area and enter comments about

the user.

Step 9 Click OK to create the CPX user.

8/6/2019 Jetstream PDF (2.6) 2005

48/240


4-6 June 2005

Modifying CPXUsers

To modify CPX user information (an Administrative privilege is

required):

Step 1 Select CPX User Administration from the Services menu. TheUpdate User Information window appears (Figure 46).

Figure 46. Update User Informations Window

In addition to modifying user information, you can also performthe following tasks:

add a new user (page 4-3)

delete an existing user (page 4-8)

Step 2 Select the user whose information you want to modify.

8/6/2019 Jetstream PDF (2.6) 2005

49/240

June 2005 4-7


Step 3 Click Modify. The Modify User window appears (Figure 47).

Figure 47. Modify User Window

Step 4 Modify the fields (if necessary) in any of the Modify User tabs

(Creating CPX Users on page 4-3.)

Step 5Click

OKto modify the CPX user.

Note

The ID and Expiration Date fields cannot be modified.

8/6/2019 Jetstream PDF (2.6) 2005

50/240


4-8 June 2005

Deleting CPXUser

To delete a CPX user (an Administrative privilege is required):

Step 1 Select the user you want to delete from the Update UserInformation window (Figure 46 on page 4-6).

Step 2 Click Delete. A message appears, asking if you want to delete the

selected user.

Step 3 Click Yes. The user is deleted.

Reviewing

CPX Users

To review the newly created or existing CPX users, select CPX

User Administration from the Services menu. The Update

User Information window (Figure 46 on page 4-6) displays theCPX users information.

8/6/2019 Jetstream PDF (2.6) 2005

51/240

June 2005 5-1

C H A P T E R 5

CPX-1000 Configuration

This chapter provides instruction for configuring the CPX-1000. It

includes the following tasks:

Modifying IP configuration (page 5-5)

Configuring global VCI settings (page 5-6)

Setting CDV value (page 5-8)

Setting LBO value (page 5-9)

Configuring the STS-1 card (page 5-10)

Setting the clock source (page 5-11)

Refreshing the CPX after modifications (page 5-13)

The CPX-1000 is shipped with the following default and a

standard configuration profile that you use JetCraft to customize

for a specific subscriber. IP address: 10.0.10.100

subnet mask: 255.255.255.0

If the CPX-1000 is configured, JetCraft automatically places the

cards in service (i.e., unlocked state) when you log in.

If the CPX-1000 has not been configured, you need to:

ensure the CPX-1000 equipment is installed

customize or modify the CPX-1000 profile

configure the CPX-1000 for telephone service

monitor equipment initialization for event messages and

alarms

8/6/2019 Jetstream PDF (2.6) 2005

52/240

5. CPX-1000 Configuration 1000-A2-GB22-10

5-2 June 2005

CPX-1000Configuration

Profile

The CPX-1000 is preprovisioned with a standard configuration

profile.

Since most of the CPX-1000 configuration parameters cannot bechanged after Interface Groups and IADs are provisioned, modify

the CPX-1000 configuration at startup.

Table 51lists the configuration parameters needed for configuring

the CPX-1000 in JetCraft.

Table 51. CPX-1000 Configurable Parameters

CPX Parameter Description

ID An identifier associated with the CPX-1000, consists of 463alphanumeric characters (e.g., JET1). No spaces, underlinedcharacters, etc. allowed.

Name A name for the CPX-1000 that consists of up to 63 alphanumericcharacters (e.g., JETSET). No spaces, underlined characters, etc.allowed.

Use this name for differentiating CPX-1000s, error reporting, andwhen creating an IAD.

IP Address The 32-bit Internet Protocol address assigned to the CPX-1000.

Default Gateway The IP address that allows the CPX-1000 to be addressed over aLAN or WAN.

Subnet Mask The 32-bit identifier that allows the IP address of the CPX-1000 tobe used with multiple connections.

Administrative State JetCraft administrative service-affecting state of CP cards andports. Options are:

Unlocked: Capable of service

Locked: Restricted from service (card is in the shelf, but

JetCraft or JetVision administrators restricted it from

service)

Operational State The operational state of the CPX-1000 cards and ports. Optionsare:

Enabled

Disabled

8/6/2019 Jetstream PDF (2.6) 2005

53/240

June 2005 5-3

1000-A2-GB22-10 5. CPX-1000 Configuration

ModifyingCPX-1000Parameters

To modify the CPX-1000 parameters:

Step 1 Select in the Tree View.

Step 2 Select Configure from the Configuration menu.

Or

Right-click in the Map View and select Configure.

The CPX Configuration window appears (Figure 51).

Figure 51. CPX Configuration Window

Step 3 Enter your modification(s) between 4 to 63 alphanumeric

characters (no spaces, underlines, or slashes).

the ID field

the Name field (the identifier used in the Map View and

identifies which IADs belong to the CPX-1000)

Note

You can modify the Name and the ID fields; other fieldsare read only.

8/6/2019 Jetstream PDF (2.6) 2005

54/240


5-4 June 2005

Step 4 Select Status. The Status tab window (Figure 52) displays the

current, read-only operational status of the CPX-1000.

Figure 52. CPX Configuration WindowStatus Tab

Step 5 Click OK to modify the CPX-1000 parameters.

ReviewingCPX-1000Parameters

To review the CPX-1000 parameters:

Step 1 Select in the Tree View.


Or

Right-click in the Map View and select Configure.

The CPX Configuration window (Figure 51 on page 5-3) displays

the name and the identifier of the CPX-1000 and other read-only

information, such as default gateway, IP address, serial number,

and subnet mask.

8/6/2019 Jetstream PDF (2.6) 2005

55/240

June 2005 5-5


Modifying IPConfiguration

To modify IP configuration, you need the following information:

IP address

Subnet mask Default Gateway

Step 1 Select the MP card from the Tree View or Shelf View.

Step 2 Select IP Configuration from the Services menu. The CPX IP

Configuration window appears (Figure 53).

Figure 53. CPX IP Configuration Window

Step 3 Type the new IP address, subnet mask, and default gateway in the

respective fields.

Note

You can modify the IP address only when the MP card isselected.

8/6/2019 Jetstream PDF (2.6) 2005

56/240


5-6 June 2005

Step 4 Click OK. A dialog box appears, asking you if you want to reboot

the CPX-1000.

Step 5 Click Yes.

When the CPX-1000 reboots, your changes are accepted.

If you click No, your changes will not take effect.

ConfiguringGlobal VCISettings

You can change the VCI value only when there are no IADs

provisioned to the CPX-1000. The default value is 1024.

Warning

Rebooting the MP card interrupts service.

Note

After you reboot the CPX-1000, we recommend that youexit and re-login to JetCraft.

Warning

Changing the VCI value requires rebooting the CPX-1000.Rebooting the CPX-1000 drops all calls.

8/6/2019 Jetstream PDF (2.6) 2005

57/240

8/6/2019 Jetstream PDF (2.6) 2005

58/240


5-8 June 2005

Setting CDVValue

Cell Delay Variation (CDV) is a QoS parameter that measures the

time needed for each cell to travel over the Virtual Circuit (VC).

The value expressed is in the microsecond (ms). The higher the

CDV value, the less the calls allowed.

To set the CDV value:

Step 1 Locate the CPX-1000 by clicking the group icon from the Tree View

where the CPX-1000 resides.

Step 2 Click a CPX-1000 and expand the tree.

Step 3 Click the CPX-1000 icon from the Tree View.

Step 4 Select Configure from the Configuration menu. The CPX


Figure 55. CPX Configuration Window

Step 5 Type the values between 1 60 in both the ATM and Frame Relay

fields (default for ATM is 8 ms and frame relay is 28 ms).

Step 6 Click OK.

8/6/2019 Jetstream PDF (2.6) 2005

59/240

June 2005 5-9


Setting LBOValue

Line Build Out (LBO) is used to offset the output attenuation.

To set the LBO value:

Step 1 Locate the CPX-1000 by clicking the group icon from the Tree Viewwhere the CPX-1000 resides.

Step 2 Click a CPX-1000 and expand the tree.

Step 3 Click the CPX-1000 icon from the Tree View.

Step 4 Select LBO Value from the Configuration menu.

The following dialog box appears.

Step 5 Select the linear measurement (feet) from the drop-down lists.

Ranges for T1 LBO are:

0133

133266 (default)

266366

399533

533655

Options for STS1 LBO are Above 100 ft. (default) or Below

100 ft.

Step 6 Click OK.

8/6/2019 Jetstream PDF (2.6) 2005

60/240


5-10 June 2005

ConfiguringSTS-1 Card

To change the frame format and line encoding on the STS-1 card:

Step 1 Click the Shelf icon associated with the CPX-1000 and expand thetree by clicking the + sign.

Step 2 Expand the STS-1 card on the Tree View, and select BITs.

Step 3 Select Configure from the Configuration menu. The Port


Figure 56. STS1 BITS Port ConfigurationStep 4 Click Status. The Status tab appears (Figure 57).

Figure 57. STS1 BITS Port ConfigurationStatus Tab

8/6/2019 Jetstream PDF (2.6) 2005

61/240

June 2005 5-11


Step 5 Select the frame format options (SF or ESF) from its drop-down list.

Step 6 Select the line encoding options (AMI or B8ZS) from its drop-down

list.

Setting ClockSource

Clock source comes from BITS (STS-1 cards) and Interface Groups.

There are 13 possible priorities. When present, priorities 1 through

4 are used for STS-1 cards and 5 through 12 for interface groups.

Priority 13 is reserved for system clock and is not user-

configurable.

When the revertive behavior is selected, it takes place across all

priorities. For example, priorities 1 and 2 lose the clock, and

priority 3 takes over and is actively driving the bus. When priority

1 regains its clock, then priority 1 will then take control of driving

the bus.

To assign priority of CPX clock source:

Step 1 Select in the Tree View, then select Clock Synch from the

Configuration menu.

Or

Right-click in the Tree View and select Clock Synch.

The Clock Synch window similar to Figure 58 appears.

Figure 58. Clock Synch Window

8/6/2019 Jetstream PDF (2.6) 2005

62/240


5-12 June 2005

Step 2 Select a row in which you want to remove a clock source.

Step 3 Remove the old clock source by double-clicking the Clock Source

field and selecting the blank line. The clock source is moved to the

Unassigned Clocks panel (Figure 59).

Figure 59. Clock Synch Window with ClocksUnassigned

Notes

The Priority and Status fields are read only.

The number of clock source available is based on thenumber of STS-1 cards and Interface Groups you haveconfigured on your CPX-1000.

8/6/2019 Jetstream PDF (2.6) 2005

63/240

June 2005 5-13


Step 4 Select a row in which you want to set a new clock source.

Step 5 Double-click the Clock Source field, and select a new clock source.

The selected clock source is moved from the Unassigned Clocks

panel and is displayed in the Clock Source field (Figure 510).

Figure 510. Clock Synch Window with Clocks Assigned

Step 6 Select a revertibility policy (default is Revertive).

Step 7 Click OK.

Refreshing theCPX-1000Display

To refresh the CPX-1000 display after youve made modifications,

select Refresh CPX from the File menu. The CPX-1000 display is

updated with your modifications, and the messageRefreshing...Done appears in the status bar.

8/6/2019 Jetstream PDF (2.6) 2005

64/240


5-14 June 2005

8/6/2019 Jetstream PDF (2.6) 2005

65/240

8/6/2019 Jetstream PDF (2.6) 2005

66/240

6. Protection Group Provisioning 1000-A2-GB22-10

6-2 June 2005

AssigningNetworkProtectionGroup

Members

Before assigning members to the network protection group, make

sure that the CPX-1000 is up with redundant ATM cards (OC-3 or

DS-3).

To assign members to the network Protection Group:

Step 1 Click Network PG on the Tree View, the right-hand pane

changes to the network Protection Group tabular view

(Figure 61).

Figure 61. Network Protection Group Tabular View

Step 2 Select a protection group to which you want to assign member.

Note

The gray background indicates that the states (active/

standby) of the card are unknown because the cardcorresponding to a member has been removed;however, the slot/port information continues to display.

Right-click these fields and select Configure

8/6/2019 Jetstream PDF (2.6) 2005

67/240

8/6/2019 Jetstream PDF (2.6) 2005

68/240


6-4 June 2005

Step 5 Select Unlocked from the Admin State drop-down list.

Step 6 Repeat Step 5 for the Secondary Member.

Step 7Select a cable type.

For OC-3 ports, select Straight.

For DS-3 ports, select either Y-cable or Straight.

Step 8 Click to select the Unidirectional 1 Plus 1 to enable the

ATM switch to automatically switch the active to standby if the

card fails.

Step 9 Click OK. The newly created Protection Groups display in the

tabular view (Figure 63).

Figure 63. Protection Groups Displayed in TabularView

Note

The APS selection is enabled only when straight cable isselected.

8/6/2019 Jetstream PDF (2.6) 2005

69/240

June 2005 6-5

1000-A2-GB22-10 6. Protection Group Provisioning

Assigning PSTNProtection

GroupMembers

Before assigning members to the PSTN network Protection Group,

make sure that the CPX-1000 is up with redundant STS-1 cards.

To assign members to the PSTN Protection Group:

Step 1 Click PSTN PG on the Tree View, the right-hand pane changes

to the PSTN Protection Group tabular view (Figure 64).

Figure 64. PSTN Protection Group Tabular View

Step 2 Select a PSTN protection group member that you want to assign.


Or

Right-click the highlighted selection and select Configure from

the pop-up menu.

The Configuration for PSTN PG window appears (Figure 65).

Right-click these fields and

select Configure

8/6/2019 Jetstream PDF (2.6) 2005

70/240


6-6 June 2005

Figure 65. Configuration for PSTN PG Window

Step 4 Select a slot and port number for the Primary Member from the

Slot/Portdrop-down list. Once a port assignment is selected, all

other fields in the area are automatically populated.

Step 5 Select Unlocked from the Admin State drop-down list.

Step 6 Repeat Step 5 for the Secondary Member.

Step 7 Select Y-cable.

Step 8 Click OK. The newly created Protection Group display in the

tabular view (Figure 66).

Figure 66. Protection Groups Displayed in TabularView

Notes

You cannot assign ports that are already members ofsome other Protection Group.

Ensure that you assign the same port type to the sameProtection Group.

8/6/2019 Jetstream PDF (2.6) 2005

71/240

June 2005 6-7


SwappingProtection

GroupMembers

To swap between the primary and secondary members of the

Protection Group:

Step 1 Place the ATM ports to which an ATM Protection Group will be

switched in the Locked state.

Step 2 Click the desired PG icon (Network or PSTN) on the Tree View, the

Protection Group Manager window similar to Figure 67.

Figure 67. Protection Group Manager

Step 3 Select a Protection Group ID to which you want to switch member.


Or

Right-click the highlighted selection and select Configure.

The Protection Group Manager window similar to Figure 68appears.

8/6/2019 Jetstream PDF (2.6) 2005

72/240


6-8 June 2005

Figure 68. Configuration for Network PG Window

Step 5 Select Locked from the Admin State drop-down list.

Step 6 Click OK to return to the Protection Group Manager window.

Step 7 Select PG Swap from the Configuration menu.

Or

Right-click the highlighted selection and select PG Swap from the

pop-up menu.

Step 8 Observe the colors. The Primary Member is now blue and the

Secondary Member green.

Note

The APS feature is not applicable for the PSTN PG.

8/6/2019 Jetstream PDF (2.6) 2005

73/240

June 2005 6-9


RemovingProtection

GroupMembers

Before removing members from a Protection Group, ensure that

the port assigned to the group member is Locked.

To remove members from a Protection Group:

Step 1 Click the desired PG icon (Network or PSTN) on the Tree View, the

Protection Group Manager window similar to Figure 69 appears.

Figure 69. Protection Group Manager

Step 2 Select a Protection Group member that you want to remove.


Or

Right-click the highlighted selection and select Configure from

the pop-up menu.

The Configuration for Network PG window similar to Figure 610

appears.

8/6/2019 Jetstream PDF (2.6) 2005

74/240

8/6/2019 Jetstream PDF (2.6) 2005

75/240

June 2005 7-1

C H A P T E R 7

Interface Groups

This chapter provides instructions to provision the Interface

Groups. These tasks include:

Creating T1 Interface Groups (page 7-2)

Creating STS-1 Interface Groups (page 7-8)

Assigning ports/channels to GR-303 Interface Groups

(page 7-12)

Removing ports/channels from GR-303 Interface Groups

(page 7-16)

Assigning ports/channels to the T1-CAS Interface Group

(page 7-18)

Removing ports/channels from the T1-CAS Interface Group

(page 7-21)

Modifying GR-303 Interface Groups (page 7-23)

Deleting GR-303 Interface Groups (page 7-25)

Performing an EOC switchover (page 7-27)

Performing a TMC switchover (page 7-29)

Configuring PPS settings (page 7-31)

JetCraft supports up to eight Interface Groups for each CPX-1000.

Each Interface Group supports up to 28 DS1 lines or 28 channels

from the CPX-1000.

Typically, the Interface Groups are created without a physical

connection. As a result, the Interface Groups are alarmed as they

are created, then cleared when they are connected to the cable.

Table 71 lists the parameters you will need to configure the

Interface Group.

Note

An empty T1 CAS Interface Group is available

Jetstream PDF (2.6) 2005

Documents

Transcript of Jetstream PDF (2.6) 2005