de werkwijze en open standaarden

112
DURA VERMEER KIEST VOOR OPEN STANDAARDEN MET OPEN STANDAARDEN DE SAMENWERKING INVULLING GEVEN >DURAVERMEER.NL/EXPERTISE/BIM

Transcript of de werkwijze en open standaarden

Page 1: de werkwijze en open standaarden

DURA VERMEER KIEST VOOR

OPEN STANDAARDENMET OPEN STANDAARDEN DE SAMENWERKING INVULLING GEVEN

>DURAVERMEER.NL/EXPERTISE/BIM

Page 2: de werkwijze en open standaarden

VOORWOORD

De afgelopen jaren was het een interessante ontdekkingsreis door de jungle van het BIM landschap. Na het opstarten, bouwen en opleveren van diverse projecten kunnen we achterom kijken en de gebaande paden in het landschap ontdekken. Nu is het tijd om een routebeschrijving uit te gaan delen zodat we de juiste bagage mee nemen, de lastige afdalingen en beklimmingen over kunnen slaan en zo efficiënt mogelijk ons doel bereiken. De ontwikkelingen staan niet stil, we zijn nog niet klaar! “Open Standaarden” Dit boek is een samenvatting van de nu (anno 2015) geldende landelijke en internationale normen en afspraken in relatie tot het proces, structuur en informatie. Als Dura Vermeer Bouw & Vastgoed zijnde hebben we centraal afspraken gemaakt over de normen die gehanteerd zullen worden en welke prioritering daaraan wordt gegeven:

1. RVB BIM norm v1.1 2. ISO 16739:2013 – i.c.m. IFC 2x3 3. NL-SfB (minimaal 4 karakters) 4. Dutch Revit Standards (DRS) V2.0

Hierin geeft de RVB BIM norm voornamelijk invulling op het gebied van structuur. Hierin wordt verwezen naar IFC 2x3 conform de ISO norm. Deze geeft de basis waar welke informatie volgens een eenduidige manier geplaatst kan worden. NL- SfB geeft helderheid in structuur en zorgt ervoor dat objecten eenvoudig herleidbaar zijn. Tot slot geeft de DRS, indien in Revit wordt gemodelleerd, handvatten aan modelleurs voor naamgeving en wijze van modelleren. Waarom kiest Dura Vermeer Bouw & Vastgoed voor Open Standaarden? Hier zijn vele redenen voor, maar de belangrijkste is dat wij een schakel in de keten zijn. Waarbij we ons realiseren dat de partijen waarmee wij samenwerken ook in andere ketens actief zijn. Om spraakverwarring te vermijden en de partijen waarmee wij samenwerken niet een Dura Vermeer methode op te leggen, is het volgens ons het beste om aan te sluiten bij de ontwikkelingen in de markt. Hiermee ook de algemene ontwikkeling van en de innovatie binnen de bouwsector te versnellen. Het geeft de andere partijen tevens meer reden om te investeren en aan te sluiten bij deze manier van werken. Met BIM in de keten efficiënter, sneller, beter, goedkoper en leuker bouwen!

Page 3: de werkwijze en open standaarden

INHOUDSOPGAVE

1. Rijks Vastgoed Bedrijf a. RVB BIM Norm v1.1

2. NL-SfB; elementenmethode ‘91 a. Toelichting

3. IFC a. Toelichting b. Entiteiten c. Quantities, Base Quantities en Propertysets d. IFC Parameteroverzicht

4. Samenhang standaarden a. BIM van structuur naar de gewenste output

Page 4: de werkwijze en open standaarden

13 woningen Mille Fleurs Waterzoom - Ede

1

Page 5: de werkwijze en open standaarden
Page 6: de werkwijze en open standaarden

RVB BIM Norm

Versie 1.1 | 1 februari 2013

Rijksvastgoedbedrijf

Page 7: de werkwijze en open standaarden

Alle rechten voorbehouden. Alle auteursrechten en databankrechten ten

aanzien van deze uitgave worden uitdrukkelijk voorbehouden.

Deze rechten berusten bij de Staat / het Rijksvastgoedbedrijf.

Behoudens de in of krachtens de Auteurswet 1912 gestelde uitzonde-

ringen, mag niets uit deze uitgave worden verveelvoudigd, opgeslagen

in een geautomatiseerd gegevensbestand of openbaar gemaakt in

enige vorm of op enige wijze, hetzij elektronisch, mechanisch, door

fotokopieën, opnamen of enige andere manier, zonder voorafgaande

schriftelijke toestemming van het Rijksvastgoedbedrijf.

Page 8: de werkwijze en open standaarden

RVB BIM Norm | 3

1 Begripsbepaling 6

1.1 Algemeen 61.2 Contextspecifiek 61.2.1 DBFMO, DBM en MC 6

2 BIM-extracten 8

2.1 Algemene vereisten aan BIM-extracten 82.1.1 Coördinatie en aspectinformatie 82.1.2 Lokale positie en oriëntatie 82.1.3 Structuur en naamgeving 92.1.4 Correct gebruik van entiteiten 92.1.5 Nauwkeurigheid 92.1.6 Doublures en doorsnijdingen 92.1.7 Modeleenheid (units), maataanduidingen, maateenheden en getalafronding 102.1.8 Informatie-indelingssystematiek en -naamgeving 102.1.9 Bouwlaagindeling (levels) en -naamgeving 102.2 Specificaties van het IFC-model 122.2.1 Begripsbepaling 122.2.2 Toepassingsgebied 122.2.3 Normatieve referenties 122.2.4 Bestandsformaat en -naam 122.2.5 Opleveringsvereisten 122.2.6 IFC-model 132.2.6.1 Geometrisch detailleringsniveau 132.2.6.2 Informatie-indeling (classification) 132.2.6.3 Objectrelaties 132.2.6.4 ObjectGUID 132.2.6.5 Geografische positie en oriëntatie 132.2.7 IFC-objecten 142.2.7.1 Project 142.2.7.2 Terrein 142.2.7.3 Bouwwerk 142.2.7.4 Bouwlaag 152.2.7.5 Bouwlaagoppervlakobject 152.2.7.6 Ruimte 152.2.7.7 Groepering van ruimten: zones 162.2.7.8 Bouwkundige, constructieve en installatietechnische elementen 182.2.7.8.1 Aspect brandveiligheid 192.2.7.8.2 Discipline constructie 192.2.7.9 Groepering van constructieve elementen 192.2.7.10 Groepering van installatietechnische elementen 192.2.7.11 Inventaris-, inrichtings- en uitrustingselementen 19

Inhoudsopgave

Page 9: de werkwijze en open standaarden

RVB BIM Norm | 4

2.3 Specificaties van de CAD-tekening 202.3.1 Begripsbepaling 202.3.2 Toepassingsgebied 202.3.3 Normatieve referenties 202.3.4 Bestandsformaat en -naam 202.3.5 Opleveringsvereisten 212.3.6 CAD-entiteiten 212.3.7 CAD-tekening 212.3.7.1 Tekeningblad 212.3.7.2 Detailleringsniveau 212.3.7.2.1 Discipline bouwkunde 212.3.7.2.2 Discipline constructie 222.3.7.2.3 Discipline werktuigbouwkunde 222.3.7.2.4 Discipline elektrotechniek 222.3.7.2.5 Aspect brandveiligheid 222.3.7.3 Tekeningstructuur 222.3.7.3.1 Aspect brandveiligheid 232.3.7.4 Informatielaagindeling (layers) en -naamgeving 242.3.7.4.1 Aspect brandveiligheid 242.4 Specificaties van de meetstaten, berekeningen, uittrekstaten 252.4.1 Begripsbepaling 252.4.2 Toepassingsgebied 252.4.3 Referenties 252.4.4 Bestandsformaat en -naam 25

3 Bij de BIM-extracten te leveren bestanden 26

3.1 Algemeen 263.1.1 BIM 263.1.2 Modeldocumentatie 263.1.3 Bestandenlijst 263.2 Contextspecifiek 273.2.1 DBFMO, DBM en MC 273.2.1.1 Relatietabel prestatiespecificaties 27

4 Bijlage 28

4.1 Nomenclatuur Bouwbesluit 2012 284.1.1 Ruimtefunctie 284.1.2 Gebruiksfunctie 284.1.3 Gebruiksgebied 284.1.4 Verblijfsgebied 284.1.5 Brandcompartimentering 284.1.6 Vluchtroute 284.2 Titelblok- en tekeninglijstgegevens 284.3 Brandveiligheid: symbolen en lijnen 284.4 Relatietabel sjabloon 28

Page 10: de werkwijze en open standaarden

RVB BIM Norm | 5

De Rijksvastgoedbedrijf BouwwerkInformatieModel Norm, kortweg RVB BIM Norm, beschrijft de specificaties van BIM-extracten en de bij deze extracten aan te leveren bestanden.

De RVB BIM Norm beschrijft noch het proces, noch de stapsgewijze technische details om tot het resultaat volgens de voorgeschreven specificaties te komen; de RVB BIM Norm omvat geen BIM/CAD handleiding.

Inleiding

Page 11: de werkwijze en open standaarden

RVB BIM Norm | 6

1.1 Algemeen

In de RVB BIM Norm worden de volgende begrippen gehanteerd:

• bouwwerk: het geheel aan bouwwerkelementen. • bouwwerkelement: een ruimtelijk of materieel onderdeel van het bouwwerk. Bouwwerkelementen zijn

de ruimtelijke, bouwkundige, constructieve en installatietechnische elementen of componenten, alsook inventaris-, uitrustings- en inrichtingselementen.

• bouwlaag: de groepering van alle bouwwerkelementen die bij een te onderscheiden verdieping van het bouwwerk behoren.

• bouwwerkinformatieproducten: de (combinaties van) bestanden en documenten die het bouwwerk beschrijven, bijvoorbeeld 3D-modellen, 2D-tekeningen en producten die gebruik maken van bouwwerk-gegevens, zoals uittrekstaten, meetstaten, berekeningen etc.

• BIM of bouwwerkinformatiemodel: het integrale 3D-informatiebronmodel van het bouwwerk zoals dit met BIM-objecten opgezet wordt in een BIM-modelleerapplicatie. Het BIM kan uit meerdere afzonderlijke modellen bestaan, ondermeer omwille van uitsplitsing op basis van de verschillende disciplines of aspecten. Het BIM omvat alle bouwwerkinformatie die benodigd is om de vereiste BIM-extracten te produceren.

• BIM-object: iedere entiteit in het BIM die informatie van het bouwwerk bevat of beschrijft, al dan niet met een geometrische representatie. Toelichting: De representatie van een bouwwerkelement in het BIM is een BIM-object.

• BIM-object-ID: vrij te kiezen identificatiecode van een BIM-object welke uniek is binnen het BIM en overgeërfd wordt binnen bepaalde BIM-extracten, en waarmee eenduidige koppelingen gemaakt kunnen worden met andere informatiegegevens.

• BIM-extracten: de bouwwerkinformatieproducten die uit het BIM afgeleid of geëxporteerd worden.

1.2 Contextspecifiek

Naargelang de specifieke context, zoals de aard van het contract of project, waarbij het aanleveren van BIM-extracten vereist is, zijn aanvullende begrippen van toepassing.

1.2.1 DBFMO, DBM en MCBij DBFMO, DBM en MC worden de volgende aanvullende begrippen gehanteerd:

• Object: in de RVB BIM Norm dient het begrip bouwwerk als het Object te worden begrepen. Het begrip Object, met hoofdletter “O”, is gedefinieerd in de Overeenkomst. Toelichting: Het begrip Object is onderscheiden van het begrip BIM-object.

• BIM: aanvullend op de algemene begripsbepaling omvat het BIM in het algemeen de representatie van het bouwwerk (het Object) en in het bijzonder de representatie van alle functievervullers waaruit het bouwwerk is samengesteld.

• functie: de door Opdrachtgever vereiste functie zoals beschreven in de prestatiespecificaties.• functie-ID: unieke identificatiecode van de functie.

Toelichting: Deze identificatiecode is de unieke code zoals die in de prestatiespecificaties aan een functie is toegekend.

1. Begripsbepaling

Page 12: de werkwijze en open standaarden

RVB BIM Norm | 7

• functievervuller: in de RVB BIM Norm dient het begrip bouwwerkelement als functievervuller te worden begrepen. Het is de door Opdrachtnemer geleverde oplossing als vervuller van de vereiste functie. Toelichting: Ten behoeve van een correcte representatie van de vervuller van een vereiste functie kan het nodig zijn om BIM-objecten zoals ruimten in het BIM op te splitsen.

• identificatielabel-ID: unieke identificatiecode van het fysieke identificatielabel (e.g. RFID-tag) van de functievervuller.

• functievervuller-ID: in de RVB BIM Norm dient het begrip BIM-object-ID als functievervuller-ID te worden begrepen. Toelichting: Deze identificatiecode is de door Opdrachtnemer vrij te kiezen, doch unieke code toegekend aan de functiever-vuller in het model.

• relatietabel: de door Opdrachtnemer op te stellen oplossing met de expliciete en ondubbelzinnige koppeling van de functievervuller-IDs aan de functie-IDs of van de functievervuller-IDs aan de identificatielabel-IDs.

Page 13: de werkwijze en open standaarden

RVB BIM Norm | 8

Onder BIM-extracten wordt begrepen:

• IFC-model;• CAD-tekening;• meetstaten, berekeningen, uittrekstaten etc.

2.1 Algemene vereisten aan BIM-extracten

In de RVB BIM Norm worden eisen gesteld aan de aan te leveren eindproducten, de BIM-extracten. Om de onderlinge consistentie van BIM-extracten te borgen naar opzet, structuur en naamgeving, zijn de in dit hoofdstuk gestelde vereisten op alle BIM-extracten van toepassing.

Toelichting: • Het exporteren van een BIM-extract vanuit het BIM-bronbestand met de bijbehorende BIM-modelleerapplicatie geeft geen

automatische garantie dat het resulterende BIM-extract voldoet aan de gestelde eisen. De aanleverende partij is te allen tijde zelf verantwoordelijk voor de technische en inhoudelijke validiteit van het BIM-extract.

• Er zijn geen merkspecifieke vereisten gesteld aan de BIM-modelleerapplicaties die benodigd zijn voor het produceren van de vereiste BIM-extracten. De applicaties moeten evenwel geschikt zijn om op correcte, efficiënte, eenvoudige en herhaalbare wijze de extracten volgens de vereiste specificaties uit het BIM te extraheren.

2.1.1 Coördinatie en aspectinformatieDe BIM-extracten, zoals IFC-modellen en CAD-tekeningen, zijn onderling gecoördineerd. Om aspectspecifieke informatie inzichtelijk te clusteren, ondermeer op basis van de gebruikelijk te onderscheiden disciplines, zijn de BIM-extracten uitgesplitst in separate aspectextracten. Deze aspect -extracten zijn onderling gecoördineerd. Het BIM-extract in de discipline bouwkunde of architectuur is het basis- en referentiemodel, dan wel de tekenkundige onderlegger voor alle andere BIM-extracten.

Toelichting: Coördinatie houdt ondermeer in dat bij het samenvoegen van de aspectmodellen of -tekeningen tot één model of tekening, alle geëxtraheerde (i.c. geëxporteerde) BIM-objecten in het BIM-extract de correcte schaal, locatie en oriëntatie hebben, zonder dat een verschaling, translatie of rotatie van een aspectmodel of -tekening hiervoor nodig is.

2.1.2 Lokale positie en oriëntatieLokale positie: in het BIM-extract is de representatie van het bouwwerk als model of tekening vlakbij het nulpunt gepositioneerd. Lokale oriëntatie: de representatie van het bouwwerk is in het algemeen zodanig georiënteerd dat de orthogonaliteit samenvalt met de x- en y-as én dat in een bovenaanzicht het noorden zoveel als mogelijk naar de bovenkant, dan wel de hoofdingang naar de onderkant wijst.

Toelichting: • De lokale positie en oriëntatie is onderscheiden van de geografische positie en oriëntatie. De vastlegging van de geografische

positie en oriëntatie is naargelang de BIM-extractsoort nader gespecificeerd. • Bij de CAD-tekening wordt onder nulpunt, het nulpunt van het World Coordinate System (WCS) begrepen.

2. BIM-extracten

Page 14: de werkwijze en open standaarden

RVB BIM Norm | 9

2.1.3 Structuur en naamgevingVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, zijn alle bestanden van of behorend bij een BIM-extract én alle entiteiten en gegevens in een BIM-extract op een logische, betekenisvolle, herkenbare, inzichtelijke, begrijpelijke en consistente wijze gestructureerd en naam gevoerd.

Toelichting: Ten behoeve van het minimaliseren van interoperabiliteitsproblemen bij de uitwisseling en koppeling van gegevens beginnen de invulwaarden in tekstvelden of vrije velden altijd met een cijfer of een letter, tenzij in deze norm expliciet anders gespecificeerd.

2.1.4 Correct gebruik van entiteitenVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, is een entiteit in het BIM-extract gemodelleerd of getekend met de voor het doel geëigende entiteit overeenkomstig het correct beoogd gebruik van de applicatie waarmee het BIM opgezet is. Voorbeeld: wand als wall-object, tekst als text-entiteit, etc.

Het BIM-extract bevat in beginsel geen proxy-objecten:• 2D-BIM-extract: een CAD-tekening mag geen enkel proxy-object bevatten.• 3D-BIM-extract: een IFC-model mag enkel en alleen een proxy-object bevatten conform de

buildingSMART IFC-specificatie, i.e. indien voor het te representeren bouwwerkelement in IFC geen geschikt IFC-object bestaat.

2.1.5 NauwkeurigheidGeometrische entiteiten in het BIM-extract zijn exact gepositioneerd. De entiteiten zijn accuraat, herkenbaar en volledig gemodelleerd of getekend overeenkomstig het vereiste detailleringsniveau, met inachtneming van de eventuele benaderingen die hierbij gebruikelijk van toepassing zijn.

2.1.6 Doublures en doorsnijdingenIn het BIM-extract komen in beginsel geen doublures voor. Er zijn geen BIM-objecten die in eenzelfde BIM-extract op eenzelfde locatie, meermaals hetzelfde representeren, ook al bestaat het BIM-extract uit meerdere aspectmodellen of -tekeningen.

Toelichting: Doublures kunnen ontstaan door tekenkundige of modelleerfouten waarbij foutievelijk meerdere kopieën van een BIM-object op eenzelfde locatie geplaatst zijn. Dergelijke doublures zijn nooit toegestaan. Doublures kunnen ook resulteren uit het disciplinespecifiek concretiseren van bouwwerkelementen. Te denken valt ondermeer aan de bouwwerkelementen in de disciplines bouwkunde en constructie. Bijvoorbeeld een vloerelement in het bouwkundig model kan in het constructiemodel geconcretiseerd zijn in de vorm van een aantal kanaalplaten. Dergelijke doublures zijn enkel en alleen toegestaan als de elementen onderling volledig passend zijn én de elementen eenduidig en consistent in een afzonderlijk aspectmodel of -tekening naar discipline te onderscheiden zijn.

Geheel of gedeeltelijke doorsnijding van BIM-objecten onderling is in beginsel niet toegestaan. Toelichting: Doorsnijdingen van bouwwerkelementen onderling zijn in het algemeen niet toegestaan, zoals bij de aansluiting van wand op wand, wand op vloer, etc. Doorsnijdingen van ondergeschikte aard, zoals deze van ingestorte of ingefreesde elektraleidingen met wanden, zijn toegestaan. Doorsnijding is in ieder geval niet toegestaan bij ontmoetingen van significante installatietechnische elementen met elementen uit de hoofddraagconstructie.

Page 15: de werkwijze en open standaarden

RVB BIM Norm | 10

2.1.7 Modeleenheid (units), maataanduidingen, maateenheden en getalafrondingHet BIM-extract is initieel opgezet gebruik makend van een metrisch sjabloon (template), waarbij 1 modeleenheid (drawing unit) = 1 mm, met weergave van:

• lengtemaat in mm of m,• oppervlaktemaat in m2,• volume in m3.

De waarden van maataanduidingen volgen uit de exacte afmetingen van gemodelleerde of getekende BIM-objecten. Het is niet toegestaan om de waarden handmatig aan te passen en hiermee model afwijkingen te corrigeren. Bij de weergave van maataanduidingen in de BIM-extracten zijn de afrondingsregels van toepassing die voor het bouwinformatieproduct geëigend en gebruikelijk zijn.

2.1.8 Informatie-indelingssystematiek en -naamgevingScheiding van informatie in het BIM-extract gebeurt volgens de systematiek van NL-SfB, gebruikmakend van de NL-SfB variant-elementen nummercodes, zonder haakjes, en bijbehorende omschrijvingen.

De NL-SfB nummercode bestaat uit 4 cijfers. Daar waar het algemene of verzamelniveau gebruikt wordt, wordt de code met één of twee nullen uitgevuld tot een viercijferige code. Het verder uitsplitsen van informatie door toevoeging van cijfers is toegestaan. In de tekst van de NL-SfB omschrijving is het leesteken “;” niet toegestaan en is vervangen door een spatie gevolgd door het koppelteken “-”.

2.1.9 Bouwlaagindeling (levels) en -naamgevingBouwlaag: zie begripsbepaling §1.1.

Toelichting: • De constructieve vloer en de afwerkvloer van een verdieping behoren als onderbegrenzing tot de overeenkomstige bouwlaag.• Een trapbordes of een incidentele tussenverdieping is in beginsel geen afzonderlijke bouwlaag. Waar nodig kunnen

aanvullende (plattegrond-)aanzichten voor dergelijke tussenverdiepingen geproduceerd worden, zonder hierbij af te wijken van de bouwlaagmodelstructuur.

Page 16: de werkwijze en open standaarden

RVB BIM Norm | 11

Notatie van de bouwlaagnaamgeving: <bouwlaagnummer><verdiepingsoort><spatie><tekstuele beschrijving>, waarbij:

• <bouwlaagnummer>: ..., -2, -1, 00, 01, 02, ..., waarbij 00 voorbehouden is voor de bouwlaag met de dominante hoofdtoegang.

• <verdiepingsoort>: - Bij een normale verdieping: code is niet van toepassing (geen karakter). - Bij een incidentele tussenverdieping: code bestaat uit 1 letter, waarbij: - a = 1ste tussenverdieping, - b = 2de tussenverdieping, - etc.• <tekstuele beschrijving>: kelder, begane grond, etc.

Voorbeelden van bouwlaagnaamgeving en aanvullende aanzichten in het geval van een tussenverdieping:

3D-BIM-extract: -2 kelder, -1 kelder, 00 begane grond, 01 eerste verdieping, etc.

2D-BIM-extract:

-2 kelder, -1 kelder, 00 begane grond, 00a tussenverdieping, 01 eerste verdieping, etc.

Page 17: de werkwijze en open standaarden

RVB BIM Norm | 12

2.2 Specificaties van het IFC-model

Naast de algemene vereisten aan BIM-extracten zijn, specifiek voor IFC-modellen, de in dit hoofdstuk gestelde specificaties van toepassing.

2.2.1 Begripsbepaling• IFC-model: 3D-BIM-extract als het totaal van IFC-objecten in één of meerdere IFC-bestanden die voldoen

aan de in de RVB BIM Norm gestelde specificaties. Het IFC-model kan bestaan uit meerdere onderling gecoördineerde deel- of aspectmodellen.

• IFC-object: de entiteit in het IFC-model die ontstaat door de extractie (i.c. export) van het overeenkomstige BIM-object uit het BIM volgens de gestelde IFC specificaties.

• IFC-object-ID: vrij te kiezen, eenvoudig herkenbare en leesbare identificatiecode van het IFC-object, welke uniek is binnen het IFC-model.

• ObjectGUID: GUID (globally unique identifier) van het IFC-object, door de BIM software gegenereerde unieke identificatiecode.

Toelichting: Naargelang de toepassing kan de IFC-object-ID of de ObjectGUID als BIM-object-ID begrepen worden.

2.2.2 Toepassingsgebied• Modelsoort: - DO/bestek (as designed) - Revisiemodel (as built, as maintained)• Disciplines: alle

2.2.3 Normatieve referentiesVoor zover in de RVB BIM Norm niet nader of afwijkend gespecificeerd, zijn de navolgende referenties van toepassing:

• IFC 2x3 TC1: http://buildingsmart-tech.org/ifc/IFC2x3/TC1/html/index.htm• BNA - NL-SfB tabellen 2005 incl. herziene Elementenmethode ’91.• NEN-EN 15221-6: “Facility Management - Part 6: Area and Space Measurement in Facility Management”.

2.2.4 Bestandsformaat en -naam• Bestandsformaat: IFC 2x3 TC1• Bestandsnaam: <projectnaam>_<aspectmodelsoort>

2.2.5 OpleveringsvereistenEr zijn geen bijkomende opleveringsvereisten, anders dan dat het aangeleverde IFC-model in IFC-formaat voldoet aan de in de RVB BIM Norm gestelde algemene en specifieke vereisten.Toelichting: • Het is toegestaan dat het IFC-model meer bouwwerkinformatiegegevens bevat dan deze die volgens de RVB BIM Norm

minimaal vereist zijn.• Zie §3 voor de bij de BIM-extracten aan te leveren bestanden.

Page 18: de werkwijze en open standaarden

RVB BIM Norm | 13

2.2.6 IFC-modelHet IFC-model voldoet aan de hierna genoemde specificaties.

2.2.6.1 Geometrisch detailleringsniveauVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, hebben geometrische IFC-objecten tenminste de herkenbare driedimensionale vorm en grootte zoals ze in hun uiterlijke vorm in de werkelijkheid verschijnen met een detailleringsniveau dat toereikend is voor de modelsoorten:

• DO/bestek (as designed) • Revisiemodel (as built, as maintained)

Toelichting: • Bijvoorbeeld een wandpakket samengesteld uit verschillende materiaallagen is in het IFC-model tenminste door de

geometrie van haar uiterlijke vorm weergegeven: dit is ter plaatste van het wandvlak de buitenzijde van de afgewerkte laag.• De aanleverende partij is zelf verantwoordelijk dat de uiterlijke verschijningsvorm en de bijhorende alfanumerieke informatie

van IFC-objecten overeenstemt met deze van de BIM-objecten in het BIM-bronbestand.

2.2.6.2 Informatie-indeling (classification)Tenminste alle IFC-objecten die een geometrische representatie van materiële bouwwerkelementen zijn, hebben een correcte IfcClassificationReference volgens de voorgeschreven naamgeving van de BIM-extracten: zie §2.1.8. De cijferparen van de NL-SfB nummercode zijn gescheiden door een punt “.”. Toegevoegde cijferparen zijn tevens met een punt gescheiden van de viercijferige NL-SfB code.

Attributes: • ItemReference: <NL-SfB nummercode>

Voorbeelden: 22.11 22.00 22.13.12

• Name: <NL-SfB omschrijving> Voorbeeld: binnenwanden - niet constructief - massieve wanden

2.2.6.3 ObjectrelatiesVoor zover elders in de RVB BIM Norm niet nader gespecificeerd, hebben de IFC-objecten onderlinge relaties conform de buildingSMART IFC-specificatie. Voor zover van toepassing hebben IFC-objecten tenminste een correcte IfcRelContainedInSpatialStructure-relatie.

Voorbeeld: Het meubel behoort tot de ruimte, de ruimte behoort tot de bouwlaag, de bouwlaag behoort tot het bouwwerk.

2.2.6.4 ObjectGUIDBij een actualisering of revisering van het IFC-model behoudt in beginsel elk IFC-object haar oorspron-kelijke GUID.

2.2.6.5 Geografische positie en oriëntatieHet IFC-model is geografisch correct georiënteerd en gepositioneerd volgens WGS84 en NAP.

Toelichting: • Denk hierbij aan de geografische positie van het terreinobject en de geografische oriëntatie (TrueNorth) van het

projectobject.• De geografische positie en oriëntatie is onderscheiden van de lokale positie en oriëntatie: zie §2.1.2.

Page 19: de werkwijze en open standaarden

RVB BIM Norm | 14

2.2.7 IFC-objectenHet IFC-model omvat, voor zover van toepassing, tenminste alle hierna genoemde IFC-objecten.

2.2.7.1 Project• Beschrijving: het project is het IFC-object met project- en modelinformatie.• Relaties: het IFC-model omvat slechts één projectobject.• IfcObject: IfcProject

Attributes: • Name: <projectnaam> • RepresentationContexts: het project is geografisch correct georiënteerd, door opgave van de

TrueNorth-waarde. • UnitsInContext: zie §2.1.7.

2.2.7.2 Terrein• Beschrijving: het terrein, de topografische site van het project.• Geometrie: 3D

Het IFC-object heeft de driedimensionale vorm en afmetingen van tenminste het terreinoppervlak van het project:

- Contour: tenminste van het kadastrale perceel of het geheel van percelen. - Hoogte: volgens de plaatselijke topografie.• Locatie: het referentiepunt van het terrein in het IFC-model is geografisch correct gepositioneerd.• Relaties: het project omvat slechts één terreinobject.• IfcObject: IfcSite

Attributes: • Name: <kadastrale aanduiding>

Voorbeeld: Delft AB 1234 Indien het project zich over meerdere kadastrale percelen uitstrekt, zijn alle kadastrale aanduidingen opgegeven, onderling gescheiden door <spatie>“-”<spatie>. Voorbeeld: Delft AB 1234 - Delft AB 1235

• RefLatitude: geografische locatie, breedtegraad op referentiepunt volgens WGS84. • RefLongitude: geografische locatie, lengtegraad op referentiepunt volgens WGS84. • RefElevation: geografische locatie, peil op referentiepunt, hoogtepeil t.o.v. NAP.

2.2.7.3 Bouwwerk• Beschrijving: zie begripsbepaling §1.1.• Relaties: - Eén of meerdere bouwwerken bevinden zich op het terrein. - Het bouwwerk is correct gepositioneerd t.o.v. het terrein.• Bijzonderheden: bouwwerken met onderling beduidend afwijkende bouwlaagindelingen bevinden zich

in beginsel in afzonderlijke, doch onderling gecoördineerde, IFC-modellen.• IfcObject: IfcBuilding

Attributes: • Name: <RVB-gebouwnummer>

Voorbeeld: 123456A78 Indien het project meerdere RVB-gebouwnummers omvat, zijn alle RVB-gebouwnummers opgegeven, onderling gescheiden door <spatie>“-”<spatie>. Voorbeeld: 123456A78 - 123456A79

Page 20: de werkwijze en open standaarden

RVB BIM Norm | 15

2.2.7.4 Bouwlaag• Beschrijving: zie begripsbepaling §1.1.• Relaties: - Een bouwwerk omvat tenminste één bouwlaag. - Ieder geometrisch IFC-object behoort tot de toepasselijke bouwlaag, met inbegrip van de onderlinge

hiërarchische relatie tussen de IFC-objecten.• IfcObject: IfcBuildingstorey

Attributes: • Name: zie §2.1.9.

Voorbeelden: -1 kelder, 00 begane grond, 01 eerste verdieping, etc.

2.2.7.5 Bouwlaagoppervlakobject• Beschrijving: het Bouwlaagoppervlakobject is het geometrische IFC-object dat expliciet de verzameling

weergeeft van de bij een bouwlaag behorende bouwwerkelementen. Het onderscheid naar binnen- of buitengebied wordt eveneens expliciet gemaakt door de betreffende verzamelingen met afzonderlijke Bouwlaagoppervlakobjecten weer te geven. Toelichting: Materiële bouwwerkelementen die de binnenruimten als omhulling begrenzen van de buitenruimte, zoals de gevel, behoren tot de verzameling van de binnenruimten.

• Geometrie: 2,5D/3D - Contour: bepaling van de omhullende begrenzing op basis van de principes van Level Area volgens

NEN-EN 15221-6. - Hoogte: van de bijbehorende bouwlaag.• Relaties: - Een bouwlaag heeft tenminste één Bouwlaagoppervlakobject. - Bouwlaagoppervlakobjecten mogen elkaar niet doorsnijden. - Een Bouwlaagoppervlakobject omsluit in beginsel geheel alle ruimten die tot de betreffende

bouwlaag behoren, uitgesplitst in hetzij uitsluitend binnenruimten, hetzij uitsluitend buitenruimten. Toelichting: Zowel het Bouwlaagoppervlakobject als de ruimte worden in het IFC-model met een IfcSpace gerepresenteerd. De genoemde relatie is een expliciet toegestane doorsnijding tussen de beide IFC-objecten.

- Ieder Bouwlaagoppervlakobject behoort tot de toepasselijke bouwlaag.• Classificatie: - n.v.t.• Opmerkingen: - De oppervlakte van een Bouwlaagoppervlakobject is geen Bruto Vloeroppervlakte (BVO) volgens NEN 2580. • IfcObject: IfcSpace

Attributes: • Name: de tekst “Gross” komt in de naam voor.

2.2.7.6 Ruimte• Beschrijving: de ruimte is het driedimensionale IFC-object dat in beginsel begrensd is door de haar

omhullende materiële bouwwerkelementen (wanden, vloeren etc.) en in haar vorm op deze omhullende elementen aansluit. Een ruimte is hetzij een binnenruimte, hetzij een buitenruimte.

• Geometrie: 3D - Contour:

In het algemeen volgt de contour van het driedimensionale object op vloerniveau de netto-contour van de ruimte langs de binnenzijde van de omhullende bouwwerkelementen. Interne bouwwerk-elementen, zoals kolommen, zijn ongeacht hun grootte als inwendige contour van het ruimteobject uitgesloten.

- Bij een ruimte in een trappenhuis, liftschacht of installatieschacht wordt in beginsel de netto-contour van de koker aangehouden.

- Indien wet- en regelgeving dit vereist, mag een ruimte waar nodig opgesplitst worden afwijkend van de materiële omhullende bouwwerkelementen.

Page 21: de werkwijze en open standaarden

RVB BIM Norm | 16

- Hoogte: In het algemeen is de hoogte van het driedimensionale object de netto-hoogte van de ruimte, gemeten vanaf de bovenzijde van de afgewerkte vloer tot aan de onderzijde van het element dat de ruimte aan de bovenzijde begrenst.

- Voor binnenruimten: de bovenbegrenzing van de ruimte is doorgaans de onderzijde van het (verlaagd) plafond. Een ruimte kan een variërende hoogte hebben binnen dezelfde bouwlaag, maar kan ook lokaal of in haar geheel een hoogte hebben die de bouwlaaghoogte overstijgt, bijvoorbeeld door het ontbreken van (delen van) een vloer of door vloeropeningen. Bouwlaagoverstijgende ruimten worden per bouwlaag opgesplitst ter hoogte van het bijbehorende bouwlaagniveau. De ruimtedelen sluiten in verticale zin op elkaar aan.

- Voor buitenruimten: bij het ontbreken van een materiële begrenzing aan de bovenzijde is de hoogte van de ruimte deze van de bouwlaag waartoe de ruimte behoort.

• Relaties: - Het bouwwerk is geheel voorzien van ruimten. - Ruimten doorsnijden elkaar niet. - Ruimten liggen steeds geheel binnen de contour van het Bouwlaagoppervlakobject.

Toelichting: Zowel de ruimte als het Bouwlaagoppervlakobject worden in het IFC-model met een IfcSpace gerepresenteerd. De genoemde relatie is evenwel een expliciet toegestane doorsnijding tussen de beide IFC-objecten.

- Iedere ruimte behoort tot de toepasselijke bouwlaag, dit is de bouwlaag waartoe het onderste begrenzende bouwwerkelement, in het algemeen de vloer, van de ruimte behoort. Ieder afzonderlijk ruimtedeel van een bouwlaagoverstijgende ruimte wordt toegekend aan de op die hoogte bijbehorende bouwlaag.

• Classificatie: - n.v.t.• Bijzonderheden: - Wordt niet als ruimte beschouwd: een bouwkundige spouw, de tussenruimte tussen een verlaagd

plafond en een vloer.• IfcObject: IfcSpace

Attributes: - Name: <IFC-object-ID> - ObjectType: ruimtefunctie volgens vigerend bouwbesluit.

Waarde uit vaste keuzelijst in bijlage: §4.1.1. Voorbeeld: verblijfsruimte

- LongName: <ruimtefunctienaam> Vrij te kiezen tekst, doch naam gevoerd volgens de algemene vereisten: zie §2.1.3. Voorbeeld: kantoorruimte

- InteriorOrExteriorSpace: [INTERNAL/EXTERNAL] volgens vigerend bouwbesluit. - BoundedBy: IfcRelSpaceBoundary: De 2nd level space boundary van de ruimte is gegenereerd. 2.2.7.7 Groepering van ruimten: zones• Beschrijving: een zone is een groepering van ruimten of ruimtedelen. Een ruimte kan behoren tot geen,

één of meerdere zones. Toelichting: Een groepering maakt het mogelijk om ruimten of ruimtedelen op een expliciete wijze in het model te clusteren en hiermee op verzamelniveau aanvullende informatie toe te kennen aan iedere ruimte die behoort tot een zone.

• IfcObject: IfcZone

Attributes - Name: code van groep, volgens de respectievelijke groepering zoals hieronder beschreven. - ObjectType: type groepering, volgens de respectievelijke groepering zoals hieronder beschreven.

Page 22: de werkwijze en open standaarden

RVB BIM Norm | 17

Toelichting: Voor bepaalde groeperingen van ruimten is in de notatie van de naamgeving een “<volgnummer>” vereist. Dit volgnummer is nodig om binnen een type groepering, zoals bijvoorbeeld “Bouwbesluit verblijfsgebied”, gelijknamige groepen van ruimten van elkaar te onderscheiden. In het bouwwerk kunnen er immers meerdere verblijfsgebieden zijn die elk afzonderlijk naar oppervlakte meetbaar moeten zijn en zodoende ook als individuele groep van elkaar te onderscheiden moeten zijn.

De volgende groeperingen worden onderscheiden:

• Groepering van ruimtedelen: Ruimten kunnen om velerlei redenen horizontaal of verticaal opgesplitst zijn in afzonderlijke ruimtedelen. Bijvoorbeeld wordt een bouwlaagoverstijgende ruimte opgesplitst in de ruimtedelen per bouwlaag. De geometrisch afzonderlijke ruimtedelen worden vervolgens gegroepeerd zodat steeds de complete ruimte als verzameling van de betreffende ruimtedelen te onderscheiden is.

- Name: <IFC-object-ID> van het dominante ruimtedeel binnen de groepering. In het geval van een ruimtedeel behorende tot een bouwlaagoverstijgende ruimte, zal het ruimtedeel met de materiële onderbegrenzing als het dominante ruimtedeel beschouwd worden. De <IFC-object-ID> van dit ruimtedeel wordt als naam van de groepering gebruikt.

- ObjectType: waarde = “ruimtegroep”

• Bouwbesluit gebruiksfunctie: - Name: gebruiksfunctie volgens vigerend bouwbesluit.

Notatie: GF_<code1>.<code2> waarbij,

- <code1>: code1 uit vaste keuzelijst in bijlage: §4.1.2. - <code2>: code2 uit vaste keuzelijst in bijlage: §4.1.2.

Voorbeeld: Een ruimte behorend tot de kantoorfunctie wordt genoteerd als: GF_05.0 Indien een ruimte volgens het vigerend bouwbesluit voldoet aan de definitie gemeenschappelijk, is in de notatie van elk van de van toepassing zijnde gebruiksfuncties het achtervoegsel “_GM” toegevoegd. Voorbeeld: Een gemeenschappelijke ruimte, in dienst van een kantoorfunctie én een bijeenkomstfunctie, behoort tot de groepen: GF_05.0_GM én GF_01.0_GM. In datzelfde bouwwerk behoren de niet gemeenschappelijke ruimten met een kantoorfunctie tot de groep: GF_05.0. De niet gemeenschappelijke ruimten met een bijeenkomstfunctie behoren tot de groep: GF_01.0. Indien een ruimte volgens het vigerend bouwbesluit voldoet aan de definitie gezamenlijk, is - analoog met het voorgaande - in de notatie van elk van de toepasselijke gebruiksfuncties het achtervoegsel “_GZ” toegevoegd. Indien een ruimte volgens het vigerend bouwbesluit een nevenfunctie vervult, behoort de ruimte zowel tot een groep met de “hoofd”gebruiksfunctie als tot een groep met de “neven”gebruiksfunctie. De groep, die een nevenfunctie vervult, heeft het achtervoegsel “_N”.

- ObjectType: waarde = “gebruiksfunctie”

• Bouwbesluit gebruiksgebied: - Name: gebruiksgebied volgens vigerend bouwbesluit.

Notatie: GG_<code>_<volgnummer> waarbij,

- <code>: code uit vaste keuzelijst in bijlage: §4.1.3. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: GG_G_01 - ObjectType: waarde = “gebruiksgebied”

Page 23: de werkwijze en open standaarden

RVB BIM Norm | 18

• Bouwbesluit verblijfsgebied: - Name: verblijfsgebied volgens vigerend bouwbesluit.

Notatie: VG_<code>_<volgnummer> waarbij,

- <code>: code uit vaste keuzelijst in bijlage: §4.1.4. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: VG_V_01 - ObjectType: waarde = “verblijfsgebied”

Pset_SpaceOccupancyRequirements: - OccupancyNumberPeak: volgens vigerend bouwbesluit het aantal personen dat maximaal

gelijktijdig in het verblijfsgebied aanwezig is.

• Bouwbesluit brandcompartimentering: - Name: (beschermd) (sub)brandcompartiment volgens vigerend bouwbesluit.

Notatie: BC_<code>_<volgnummer> waarbij,

- <code>: code uit vaste keuzelijst in bijlage: §4.1.5. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: BC_BC_01 - ObjectType: waarde = “brandcompartiment”

• Bouwbesluit vluchtroute: - Name: vluchtroute volgens vigerend bouwbesluit.

Notatie: VR_<code>_<volgnummer> waarbij,

- <code>: code uit vaste keuzelijst in bijlage: §4.1.6. - <volgnummer>: 01, 02, 03, etc. Voorbeeld: VR_bVR_01 - ObjectType: waarde = “vluchtroute”

2.2.7.8 Bouwkundige, constructieve en installatietechnische elementen• Beschrijving: de materiële bouwwerkelementen die deel uitmaken van het gebouw: bouwkundige,

constructieve en installatietechnische elementen.• Geometrie: 3D

Zie IFC-modelspecificaties (Geometrisch detailleringsniveau): §2.2.6.1. De elementen zijn in beginsel per bouwlaag gemodelleerd.

• Relaties: ieder bouwwerkelement behoort tot de toepasselijke bouwlaag.• Classificatie: - zie §2.2.6.2.• Bijzonderheden: - elementen in de discipline bouwkunde hebben een materiaaltoekenning.

IfcMaterial: vrij te kiezen materiaalnaam, doch naam gevoerd volgens de algemene vereisten van BIM-extracten én consistent toegepast in het IFC-model.

- deuren en ramen hebben een correcte representatie van de draairichting (operation type) en zijn gedefinieerd met de toepasselijke IfcDoorStyle of IfcWindowStyle.

• IfcObject: ieder bouwwerkelement wordt correct en consistent gerepresenteerd met het geschikte IfcObject: IfcBuildingElement (IfcBeam, IfcColumn, IfcDoor, IfcSlab, IfcWall, IfcWindow, etc.), IfcDistributionElement, IfcElectricalElement, IfcTransportElement, etc.

Attributes: - Name: <IFC-object-ID> • Pset_###Common: voor zover de eigenschap van toepassing is bij het betreffende modelobject: - IsExternal: [True/False]

Page 24: de werkwijze en open standaarden

RVB BIM Norm | 19

2.2.7.8.1 Aspect brandveiligheid• Pset_###Common: voor zover de eigenschap van toepassing is bij het betreffende modelobject: - FireRating: weerstand tegen branddoorslag en brandoverslag, WBDBO waarde volgens vigerend

bouwbesluit (in minuten). Het betreft de werkelijke WBDBO waarde, niet de gestelde eis. Voorbeeld: 60

- Compartmentation: [True/False] o.a. van toepassing bij IfcWall

Specifiek voor een IFC-object dat toegang tot een ruimte verschaft (zoals een deur), zijn aanvullend de volgende eigenschappen van toepassing:• Pset_###Common - FireExit: [True/False]: de waarde “True” is toegekend aan alle elementen die een uitgang voor

ontvluchting zijn, zoals bepaalde deuren. - SelfClosing: [True/False] - SmokeStop: [True/False]

2.2.7.8.2 Discipline constructie• Pset_###Common: voor zover de eigenschap van toepassing is bij het betreffende modelobject: - LoadBearing: [True/False]: de waarde “True” is toegekend aan alle elementen die constructief

dragend zijn.• alle elementen in de discipline constructie zijn ook in hun constructief analytische weergave in het

IFC-model aanwezig met hun toepasselijke krachtswerking. IfcStructuralItem (ItcStructuralMember, IfcStructuralConnection) IfcStructuralActivity (IfcStructuralAction, IfcStructuralReaction)

2.2.7.9 Groepering van constructieve elementen IfcStructuralLoadGroup is toegepast voor de groepering van belastingcombinaties.

IfcStructuralAnalysisModel is toegepast als systeem voor het constructieve analytische model.

2.2.7.10 Groepering van installatietechnische elementen IfcElectricalCircuit is toegepast als systeem voor de stroomdistributie elementen.

2.2.7.11 Inventaris-, inrichtings- en uitrustingselementen• Beschrijving: inventaris, inrichtings- en uitrustingselementen.• Geometrie: zie IFC-modelspecificaties (Geometrisch detailleringsniveau): §2.2.6.1.• Relaties: - Ieder element behoort tot de toepasselijke bouwlaag. - Voor zover een element in een ruimte gelegen is, behoort het element tot de haar omhullende

ruimte.• Classificatie: - zie §2.2.6.2.• IfcObject: ieder element wordt correct en consistent gerepresenteerd met het geschikte IfcObject

(IfcFurnishingElement, IfcEquipmentElement, etc.). Attribute: - Name: <IFC-object-ID>

Page 25: de werkwijze en open standaarden

RVB BIM Norm | 20

2.3 Specificaties van de CAD-tekening

Naast de algemene vereisten aan de BIM-extracten zijn, specifiek voor CAD-tekeningen, de in dit hoofdstuk gestelde specificaties van toepassing.

2.3.1 Begripsbepaling• CAD-tekening: 2D-BIM-extract als het totaal van tekeningbladen met CAD-entiteiten in een

CAD-bestand dat voldoet aan de in de RVB BIM Norm gestelde CAD-specificaties.• tekeningblad: het blad in de CAD-tekening met het tekeningkader waarbinnen het titelblok samen

met bijvoorbeeld een renvooi, overzichtstekening, een viewport of andere entiteiten geplaatst zijn. Het tekeningblad is bestemd voor weergave op een digitaal of papieren document.

2.3.2 Toepassingsgebied• Tekenwerksoort: - DO/bestek (as designed) - Revisietekenwerk (as built, as maintained)• Disciplines: alle

2.3.3 Normatieve referentiesOnderstaande referenties zijn integraal van toepassing tenzij anders aangegeven. Voor zover inhoudelijk overlappend, prevaleert de eerstgenoemde norm of referentie. In alle gevallen prevaleert hetgeen dat in de RVB BIM Norm gespecificeerd is.

• BNA - NL-SfB tabellen 2005 incl. herziene Elementenmethode ’91.• GB CAS 4.0 “GB CAD Afsprakenstelsel 4”. - De bepalingen onder §2 zijn optioneel. - Inclusief de in §5 en §6 genoemde voorkeuren.• NEN-ISO 128-40:2001 “Technische tekeningen -- Algemene principes voor de weergave -- Deel 40:

Basisafspraken voor doorsneden”. - De bepalingen onder NEN-ISO 128-50:2001 §9 zijn niet van toepassing.• NEN-ISO 5455:1990 & /C1:1996 “Technische tekeningen -- Schalen”.• NEN-EN-ISO 5457:1999 & /A1:2010 “Technische product-documentatie -- Formaten en inrichting van

tekenbladen”. - Inclusief de in §3.1 genoemde voorkeuren. - De bepalingen onder §4.3, §4.4, §4.5 zijn optioneel. - De bepalingen onder NEN-EN-ISO 7200:2004 §5 zijn optioneel.• NEN 1413 “Symbolen voor veiligheidsvoorzieningen op bouwkundige tekeningen en in bouwkundige

schema’s”.• NEN 2302:1983 “Tekeningen in de bouw -- Algemene regels”. - De bepalingen onder §2.7.1 zijn optioneel. - Inclusief de in §5.1.1 genoemde voorkeuren.• NEN 2574:1993 “Tekeningen in de bouw -- Indeling van gegevens op tekeningen voor gebouwen”.• NPR 2570:1986 “Tekeningen in de bouw -- Coördinatie van gegevens op tekeningen voor gebouwen”. - Uitsluitend §2.

2.3.4 Bestandsformaat en -naam• Bestandsformaat: - DWG 2007: het bestand dient opzichzelfstaand in de courante versie van Autodesk AutoCAD bruikbaar

te zijn, zonder bijvoorbeeld toegevoegde applicaties of bibliotheken. Toelichting: Trusted DWG is geen vereiste, maar het bestand is inhoudelijk geheel compatibel met de courante versie van Autodesk AutoCAD.

- PDF/E: alle bijbehorende fonts zijn embedded aanwezig.• Bestandsnaam: in beginsel vrij te kiezen.

Bij plattegronden vangt de bestandsnaam aan met de bouwlaagnaamgeving, zoals vereist volgens de algemene vereisten van BIM-extracten: zie §2.1.9.

Page 26: de werkwijze en open standaarden

RVB BIM Norm | 21

2.3.5 OpleveringsvereistenDe CAD-tekening en bijbehorende tekeningbladen worden respectievelijk in DWG- én PDF-formaat aangeleverd. Ze voldoen aan de in de RVB BIM Norm gestelde algemene en specifieke vereisten. Bij oplevering van de CAD-tekening:• is de tekening volledig opgeschoond;

Toelichting: Denk hierbij ondermeer aan het verwijderen van hulplijnen of overbodige lijnen afkomstig van extractie uit 3D-geometrie die de leesbhaarheid van entiteiten in de tekening verstoren, denk ook aan het gebruik van een functie zoals “purge”.

• zijn in de tekening geen toegevoegde entiteiten aanwezig zoals OLE-objecten, dictionaries, rasterbe-standen, external references, LISP- of VBA-routines, hyperlinks, databasekoppelingen: zie ook: §2.1.4 m.b.t. proxy-objecten;

• is layer 0 ingesteld als de current layer;• zijn aan de layout tabs geen printer- of plotterdefinities gekoppeld;• zijn alle layout tabs weergegeven als zoom extents;• is de system variable MEASUREMENT ingesteld op 1.Toelichting: Zie §3 voor de bij de BIM-extracten aan te leveren bestanden.

2.3.6 CAD-entiteiten• Er zijn slechts één- en tweedimensionale entiteiten getekend in het xy-vlak van het WCS.• Repeterende elementen zijn waar mogelijk en gebruikelijk gedefinieerd als een block. - Binnen een renvooi zijn geen blocks toegepast.• De elevation, z-waarde, thickness, linewidth, en global width van entiteiten zijn 0 of default (waarbij default

ingesteld is op 0). Eigenschappen van entiteiten zijn by Layer of by Entity.

2.3.7 CAD-tekeningDe CAD-tekening voldoet aan de hierna genoemde specificaties.

2.3.7.1 TekeningbladDe tekeningbladen in de CAD-tekening voldoen aan de volgende vereisten:• Wanneer gevisualiseerd naar (virtueel) papier van het bedoelde formaat zijn de tekeningen, en in het

bijzonder de linetypes en materiaalaanduidingen daarin, goed zichtbaar en te onderscheiden.• Lijndikte wordt slechts bepaald door koppeling aan kleur.• Elk tekeningblad is voorzien van één titelblok (identificatiestrook). Het titelblok bevat de gegevens

gespecificeerd in de bijlage §4.2.

2.3.7.2 DetailleringsniveauHet detailleringniveau is minimaal conform fase bestek (volgens NEN 2574). Naargelang discipline of aspect voldoen de tekeningen aan de volgende aanvullende vereisten:

2.3.7.2.1 Discipline bouwkundeAlle in het werk te realiseren (as designed) of gerealiseerde (as built) bouwwerkelementen zijn getekend. Minimaal gaat het hierbij om de volgende bouwwerkelementen:• Wanden, vloeren, en daken; inclusief de plaatselijke onderbrekingen daarin (vides, sparingen, etc.);• Wand-, vloer-, en dakopeningen (deuren, ramen, luiken, daklichten, rook/warmteafvoer, etc.) inclusief

globale representatie van vulling (kozijn, raamhout, profielen, etc.) en draairichting van eventueel beweegbare of bewegende delen in de vorm van een straalboog of bewegingsrichting in de vorm van een pijl.

• Wandafwerkingen die vanwege wet- en regelgeving zijn voorzien van een attest of certificaat, inclusief materiaalaanduiding.

- De tekst in het renvooi komt overeen met de materiaalnaam of aanduiding in het attest of certificaat.• Verticale verkeersvoorzieningen (trappen, hellingen, liften, etc.), waar gebruikelijk voorzien van een pijl

in de stijgrichting;• Balustrades en leuningen;• Vaste voorzieningen (keukens, sanitair, kasten, etc.).

Page 27: de werkwijze en open standaarden

RVB BIM Norm | 22

2.3.7.2.2 Discipline constructie• Voor deze discipline is het bestaande wettelijk kader het eerste uitgangspunt. Minimaal zijn alle

bouwwerkelementen van de hoofddraagconstructie getekend. • Op tekening is afleesbaar: - Het onderscheid tussen geprefabriceerd beton en in het werk gestort beton. - Betonkwaliteiten en staalsoorten. - Tijdsduur tot bezwijken, indien bepaald tijdens het ontwerpen van een bouwwerkelement of

materiaal.

2.3.7.2.3 Discipline werktuigbouwkunde• De volgende werktuigbouwkundige bouwwerkelementen zijn getekend: - Brandkleppen; - Brandafsluiters t.b.v. compartimentdoorvoer door een W-installatie; - (nood)Afsluiters van gebouwinstallaties; - (nood)Schakelaar van gebouwinstallaties.

2.3.7.2.4 Discipline elektrotechniek• De volgende elektrotechnische bouwwerkelementen zijn getekend: - Brandafsluiters t.b.v. compartimentdoorvoer door een E-installatie.

2.3.7.2.5 Aspect brandveiligheid• Alle in het werk te realiseren, dan wel gerealiseerde brandveiligheidsvoorzieningen worden getekend.

Minimaal gaat het hierbij om de voorzieningen welke zijn genoemd in de bijlage §4.3 en NEN 1413. - (Beschermde) (sub)brandcompartimenten zijn aangegeven met behulp van compartimentlijnen die

zijn voorzien van eigenschappen zoals opgenomen in §4.3. - Brandveiligheidsvoorzieningen zijn weergegeven met de symbolen zoals opgenomen in §4.3. - Indien brandveiligheidsvoorzieningen hun oorsprong vinden in een andere discipline (bouwkunde,

elektrotechniek, etc.) kan het voorkomen dat een bouwwerkelement of voorziening meerdere malen gerepresenteerd wordt in de set revisietekeningen van een bouwwerk. Dit is toegestaan mits de verschillende representaties onderling niet strijdig zijn.

2.3.7.3 TekeningstructuurDe tekeningen voldoen aan de volgende vereisten:• Plattegronden zijn in beginsel een horizontale doorsnede op 1200 mm boven het vloerpeil van de

desbetreffende bouwlaag. - Als hiermee een tekening ontstaat die niet goed afleesbaar is of tot ongewenste bouwkundige

interpretaties aanleiding geeft, mag het doorsnijdingsvlak op een andere hoogte gelegd worden (ook lokaal). In voorkomende gevallen wordt een verklarende tekst in de tekening opgenomen.

• In aanvulling op het bepaalde in NEN-ISO 128-30 wordt ook de projectie van bouwwerkelementen gelegen vóór (boven) het doorsnijdingsvlak op tekening weergegeven.

• Tekenkundig onderscheid van de ligging van bouwwerkelementen ten opzichte van het doorsnij-dingsvlak is conform het volgende:

- Bouwwerkelementaanzicht: - Lijndikte kleiner dan bij doorsnede; - Lijntype getrokken lijn; - Geen arcering. - Bouwwerkelementdoorsnijding: - Lijndikte groter dan aanzicht en projectie; - Lijntype getrokken lijn; - Arcering. - Bouwwerkelementprojectie: - Lijndikte kleiner dan bij doorsnede; - Lijntype onderbroken lijn; - Geen arcering.

Page 28: de werkwijze en open standaarden

RVB BIM Norm | 23

• Doorsneden van bouwwerkelementen zijn voorzien van materiaalaanduiding met behulp van een arcering.

• Bouwwerkelementen getekend in aanzicht zijn bij noemenswaardige verschillen in afstand (diepte) vanaf het doorsnijdingsvlak voldoende visueel onderscheiden. Het gebruik van een afnemende mate aan detaillering en successievelijk dunnere of lichtere lijntypen heeft hiervoor de voorkeur.

- Hierbij moet gedacht worden aan delen van onderliggende verdiepingen zichtbaar door vloer openingen in een plattegrond, of terugliggende bouwdelen in een doorsnede of aanzicht.

• In aanzichten zijn vlakvullingen en beschaduwingen aangegeven met arceerpatronen.• De onderstaande informatie-elementen zijn aanwezig. - Alle projecties zijn voorzien van: - Stramien, inclusief maataanduidingen, waarmee een referentie ontstaat voor plaatsbepaling van

bouwwerkelementen. - Uitwendige maten van het bouwwerk. - Van elk vloerveld, hoogtemaat van bovenzijde afgewerkte vloer. - De netto doorgangsmaat (hoogte en breedte) van alle wand-, vloer-, en dakopeningen (met name

deuren en doorgangen). - Plattegronden zijn bovendien voorzien van: - Doorsnedeaanduidingen van aanwezige verticale doorsneden. - Voor elke ruimte: tenminste de bijbehorende ruimtefunctienaam als vrij te kiezen tekst, naam

gevoerd volgens de algemene vereisten in §2.1.3, ruimtenummer en oppervlakte. - Doorsneden zijn bovendien voorzien van: - Netto hoogtematen van verdiepingen met tussenliggende en totaalmaten, ten opzichte van het

vastgestelde peil. - Aanzichten zijn bovendien voorzien van: - Hoofdgevelmaten, goothoogten, en nokhoogten, ten opzichte van het vastgestelde peil.• Alle in een tekening voorkomende arceringen, symbolen, en afwijkende linetypes zijn in een renvooi

opgenomen met hun verklaring. - Corresponderende elementen zijn hetzelfde in de renvooien binnen het tekenwerk van één

bouwwerk. - Linetypes voor stramienlijnen, afbreeklijnen, en bouwwerkelementprojecties hoeven niet opgenomen

te worden. - Indien noodzakelijk voor een goed begrip kan een afwijkend linetype voorzien worden van een

verklarende tekst in de tekening in modelspace. - Voor symbolen mag conform NEN 2302 §4.3 worden volstaan met een verwijzing naar een staat of

norm.• Wanneer binnen een tekening slechts een onderdeel van een bouwwerk (bijvoorbeeld een bouwdeel,

een ruimte of een detail) afgebeeld wordt, dan is er een overzichtstekening die duidelijk maakt waar het desbetreffende onderdeel zich bevindt binnen het totaal te realiseren of gerealiseerde bouwwerk. Een overzichtstekening bevat bijvoorbeeld de volgende informatie:

- een schematische situatietekening, - een schematische plattegrond van het bouwwerk waarop het totaal en het beschouwde deel is

aangegeven; - een schematische doorsnede van het bouwwerk waarop verdieping of kijkrichting is aangegeven.• Schrift in de tekeningen is gesteld in de Nederlandse taal.

2.3.7.3.1 Aspect brandveiligheidTekeningen voor het aspect brandveiligheid voldoen aan de volgende aanvullende vereisten:• De corresponderende bouwkundige tekening is als ‘onderlegger’ toegevoegd, als enkel block welke zich

op layer 0 bevindt.• Ieder symbool (met uitzondering van compartimentlijnen) bestaat uit een block met de inhoud en

eigenschappen zoals voorgeschreven in bijlage §4.3. • Compartimentlijnen bestaan uit een polyline met de in bijlage §4.3 voorgeschreven eigenschappen.

Page 29: de werkwijze en open standaarden

RVB BIM Norm | 24

2.3.7.4 Informatielaagindeling (layers) en -naamgevingScheiding van informatie gebeurt door plaatsing van entiteiten op layers. Entiteiten in de tekeningen zijn geplaatst op de toepasselijke layer met de laagnaamgeving volgens de voorgeschreven naamgeving van de BIM-extracten: zie §2.1.8. Notatie van de laagnaamgeving: <NL-SfB nummercode><spatie><NL-SfB omschrijving>

Voorbeelden: 2200 binnenwanden2210 binnenwanden - niet constructief

2.3.7.4.1 Aspect brandveiligheidTekeningen voor het aspect brandveiligheid voldoen aan de volgende aanvullende vereisten:• Alle getekende brandveiligheidsinformatie, zoals symbolen en lijnen zijn geplaatst op de layer met code

6510.• Compartimentlijnen hebben de bijbehorende eigenschappen in het achtervoegsel van de laagnaam-

geving gecodeerd, volgens het format TTT_EIW_SX_B_SN waarbij: - TTT = Tijd in minuten (3 karakters); - EIW = kwaliteitsaanduiding (3 karakters); - SX = rookwerendheid (2 karakters); - B = Brandklasse (1 karakter); - SN = Rookklasse (2 karakters). De velden komen overeen met de eigenschappen van het symbool compartimentscheiding (symbool

6.4.16 volgens NEN 1413). Indien een karakter met leeg of afwezig geduid moeten worden, wordt een nul “0” voor dit karakter gebruikt.

Page 30: de werkwijze en open standaarden

RVB BIM Norm | 25

2.4 Specificaties van de meetstaten, berekeningen, uittrekstaten

Naast de algemene vereisten aan de BIM-extracten zijn, specifiek voor meetstaten, berekeningen, uittrekstaten, e.d. de in dit hoofdstuk gestelde specificaties van toepassing.

2.4.1 Begripsbepaling-

2.4.2 Toepassingsgebied• Productsoort: - DO/bestek (as designed) - Revisie (as built, as maintained)• Disciplines: alle

2.4.3 Referenties-

2.4.4 Bestandsformaat en -naam• Bestandsformaat: toepasselijk bestandsformaat indien elders niet nader gespecificeerd.• Bestandsnaam: vrij te kiezen indien elders niet nader gespecificeerd.

Page 31: de werkwijze en open standaarden

RVB BIM Norm | 26

Bij de aanlevering van BIM-extracten worden ook de onderstaande bestanden aangeleverd.

3.1 Algemeen

3.1.1 BIM• BIM-bronbestand en de daarmee samenhangende bestanden die benodigd zijn om het geleverde extract

compleet en op eenvoudige en herhaalbare wijze te reproduceren. Toelichting: Het BIM kan ook bestaan uit meerdere afzonderlijke modellen die onderling gecoördineerd zijn.

• Bestandsformaat: vrij te kiezen, in origineel (merkspecifiek) bronbestandsformaat.• Bestandsnaam: vrij te kiezen.

3.1.2 Modeldocumentatie • Logboek met beschrijving van: - Noemenswaardige modelleerkeuzes, -afspraken, etc. - Instructie om op eenvoudige en herhaalbare wijze alle extracten uit het BIM te reproduceren. - BIM-applicatie- en systeemgegevens: softwarenaam en -versie, besturingssysteem en -versie.• Bestandsformaat: Word of ODF• Bestandsnaam: <projectnaam>_modeldocumentatie

3.1.3 Bestandenlijst• Lijst van de aangeleverde bestanden (incl. contextspecifieke bestanden: zie §3.2) met vermelding van de

bestandsnamen, -formaten, formaatversies en beknopte beschrijvingen van de bestandsinhoud. In de lijst is ook de aangeleverde mappenstructuur toegelicht.

- Specifiek voor CAD-tekeningen: de lijst omvat ook een tekeninglijst met daarin de gegevens zoals aangegeven in bijlage §4.2. Deze gegevens corresponderen met de gegevens in het titelblok.

- Daar waar het bijkomende of niet uit het BIM geëxtraheerde bestanden betreft, zoals bijvoorbeeld constructieve berekeningen of materiaalcertificaten, zijn deze via het BIM-object-ID aan het bijbehorende bouwwerkelement gekoppeld, minstens in de bestandenlijst of in een aparte relatietabel.

• Bestandsformaat: Excel of ODS• Bestandsnaam: <projectnaam>_bestandenlijst

3. Bij de BIM-extracten te leveren bestanden

Page 32: de werkwijze en open standaarden

RVB BIM Norm | 27

3.2 Contextspecifiek

Naargelang de specifieke context, zoals de aard van het contract of project, waarbij het aanleveren van BIM-extracten vereist is, zijn – naast de algemeen bij de BIM-extracten aan te leveren bestanden – ook aanvullende bestanden vereist.

3.2.1 DBFMO, DBM en MC

3.2.1.1 Relatietabel prestatiespecificatiesDe door Opdrachtnemer op te stellen oplossing met de expliciete en ondubbelzinnige koppeling van de functievervuller-IDs aan:• resp. de functie-IDs. Deze relatie kan één op veel zijn. • resp. de identificatielabel-IDs, voor deze functievervullers die ook fysiek identificeerbaar zijn met een

identificatielabel. Deze relatie is één op één. Toelichting: In de prestatiespecificaties is bepaald welke functievervullers een identificatielabel dienen te hebben.

De aan te leveren oplossing is tenminste gelijkwaardig met onderstaande voorbeeldoplossing:• Tabel met de relatiekoppelingen.• Bestandsformaat: Excel of ODS.• Bestandsnaam: <projectnaam>_relatiemodel• Sjabloon: zie bijlage §4.4.

De tabel omvat de expliciete en ondubbelzinnige koppeling van de functievervuller-IDs aan:• resp. de functie-IDs. De koppeling is vastgelegd in relatietabel 1, waarbij: - 1e kolom: functievervuller-IDs - 2e kolom: functie-IDs• resp. de identificatielabel-IDs. De koppeling is vastgelegd in relatietabel 2, waarbij: - 1e kolom: functievervuller-IDs - 2e kolom: identificatielabel-IDs

Schematisch voorbeeld van relatietabel met koppeling van functievervuller-IDs aan functie-IDs

BIM-extract relatietabel prestatiespecificaties

A

F G

E

B C D Func

tieve

rvul

ler-

ID

Func

tie-I

D

A 1.1

B 1.1

C 1.1

D 1.1

E 1.2.2

F

G 1.2.1.1

G 1.2.1.2

functievervullers functies

1.1 Kantooralgemeen

1.2.2Verkeersruimte

1.2.1.1Archief DIV

1.2.1.2Archief inspectie

Page 33: de werkwijze en open standaarden

RVB BIM Norm | 28

De genoemde documenten zijn externe bijlagen beschikbaar op de RVB-website.

4.1 Nomenclatuur Bouwbesluit 2012

Lijst “RVB BIM Norm v1.0 - bijlage - nomenclatuur BB2012” omvat de onderstaande lijsten op de gelijknamige tabbladen.

4.1.1 Ruimtefunctie

4.1.2 Gebruiksfunctie

4.1.3 Gebruiksgebied

4.1.4 Verblijfsgebied

4.1.5 Brandcompartimentering

4.1.6 Vluchtroute

4.2 Titelblok- en tekeninglijstgegevens

Lijst “RVB BIM Norm v1.0 - bijlage - titelblok- en tekeninglijstgegevens”.

4.3 Brandveiligheid: symbolen en lijnen

Lijst “RVB BIM Norm v1.0 - bijlage - brandveiligheid symbolen en lijnen”.

4.4 Relatietabel sjabloon

Lijst “RVB BIM Norm v1.0 - bijlage - relatietabel sjabloon”.

4. Bijlage

Page 34: de werkwijze en open standaarden

RVB BIM Norm | 29

Page 35: de werkwijze en open standaarden

RVB BIM Norm | 30

Page 36: de werkwijze en open standaarden

RVB BIM Norm | 31

Deze brochure is een uitgave van:

Het RijksvastgoedbedrijfKorte Voorhout 7, 2511 CW Den Haagwww.rijksvastgoedbedrijf.nl

Februari 2013

Page 37: de werkwijze en open standaarden

Tuindorp - Zoetermeer

2

Page 38: de werkwijze en open standaarden

Zalmplaatschool - Rotterdam

2

Page 39: de werkwijze en open standaarden

NL-SfB, Elementenmethode '91

Toepassing

Een indeling op bouwdelen is een veel gebruikte manier om een gebouw geordend weer te geven. Bouwdelen

worden gerangschikt volgens een bepaalde methode. De meest gebruikte methode is die van de NL-SfB. De

NL-SfB is een manier van indelen met een eigen codering. De NL-SfB codering heeft zich in Nederland

ontwikkeld tot een standaard op het gebied van elementgerichte classificaties en wordt veel toegepast bij

meerjarenonderhoud. De NL-SfB codering deelt het gebouw op in elementen die elk onder een eigen rubriek

worden geplaatst. Zo vallen bijvoorbeeld alle buitenkozijnen onder de rubriek buitenwandopeningen. Deze

indeling zorgt er echter voor dat onderdelen waar een bouwdeel uit bestaat in verschillende rubrieken kan

vallen.

Historie

De SfB-codering is in de jaren vijftig in Zweden ontwikkeld voor classificatie van gebouwdelen ten behoeve van

kostencalculaties en bestekomschrijvingen. SfB staat voor “Samarbestkommitte Byggnadsfragor”, wat

'samenwerkingscommite voor bouwvraagstukken' betekent. Sinds 1977 is er een Nederlandse SfB-commissie,

die een indelingstabel voor de Nederlandse bouwsector heeft ontwikkeld onder de naam NL-SfB.

De norm wordt in 2015 van de BNA overgedragen op het BIM Loket, deze zal de norm beheren.

Opbouw

De SfB-code, bestaat uit drie delen:

1. Met het eerste deel van de SfB-code wordt verwezen naar het bouwdeel, de plaats waar het product in

het gebouw of het terrein zit. Bijvoorbeeld funderingsconstructies of vloerafwerking.

2. Met het tweede deel wordt verwezen naar de vorm of functie van het product, zoals baanvormige

(dak)bedekking, isolatie of beplanting.

3. Met het derde deel wordt aangegeven waar het product van gemaakt is, bijvoorbeeld van marmer,

linoleum of beton.

Besluit

Dura Vermeer volgt de RvB BIM Norm (artikel 2.1.8) betreft de methode hoe gebouwen gedecomposeerd

moeten worden. Dit wordt gedaan aan de hand van viercijferige code.

Zie voorbeeld:

xx 31.0 Buitenwandopeningen

xx.x 31.2 Buitenwandopeningen; Gevuld met

ramen

xx.xx 32.25 Buitenwandopeningen; Gevuld met

ramen, combinatieramen

Element

Variant-elementgroep

Variant-element

Page 40: de werkwijze en open standaarden

1- FUNDERINGEN 11 bodemvoorzieningen

13 vloeren op grondslag

16 funderingsconstructies

17 paalfunderingen

2- RUWBOUW 21 buitenwanden

22 binnenwanden

23 vloeren

24 trappen en hellingen

27 daken

28 hoofddraagconstructies

3- AFBOUW 31 buitenwandopeningen

32 binnenwandopeningen

33 vloeropeningen

34 balustrades en leuningen

37 dakopeningen

38 inbouwpakketten

4- AFWERKINGEN 41 buitenwandafwerkingen

42 binnenwandafwerkingen

43 vloerafwerkingen

44 trap- en hellingafwerkingen

45 plafondafwerkingen

47 dakafwerkingen

48 afwerkingspakketten

5- INSTALLATIES WERKTUIGBOUWKUNDIG 51 warmte-opwekking

52 afvoeren

53 water

54 gassen

55 koude-opwekking en distributie

56 warmtedistributie

57 luchtbehandeling

58 regeling klimaat en sanitair

6- INSTALLATIES ELEKTROTECHNISCH 61 centrale electrotechnische voorzieningen

62 krachtstroom

63 verlichting

64 communicatie

Page 41: de werkwijze en open standaarden

65 beveiliging

66 transport

67 gebouwbeheervoorzieningen

7- VASTE VOORZIENINGEN 71 vaste verkeersvoorzieningen

72 vaste gebruikersvoorzieningen

73 vaste keukenvoorzieningen

74 vaste sanitaire voorzieningen

75 vaste onderhoudsvoorzieningen

76 vaste opslagvoorzieningen

8- LOSSE INVENTARIS 81 losse verkeersinventaris

82 losse gebruikersinventaris

83 losse keukeninventaris

84 losse sanitaire inventaris

85 losse schoonmaakinventaris

86 losse opslaginventaris

9- TERREIN 90 terrein

Page 42: de werkwijze en open standaarden

1- FUNDERINGEN

11 bodemvoorzieningen

11.10 bodemvoorzieningen; grond, algemeen (verzamelniveau)

11.11 bodemvoorzieningen; grond, ontgravingen

11.12 bodemvoorzieningen; grond, aanvullingen

11.13 bodemvoorzieningen; grond, sloop- en rooiwerkzaamheden

11.15 bodemvoorzieningen; grond, damwanden

11.20 bodemvoorzieningen; water, algemeen (verzamelniveau)

11.24 bodemvoorzieningen; water, bemalingen

11.25 bodemvoorzieningen; water, damwanden

13 vloeren op grondslag

13.10 vloeren op grondslag; niet constructief, algemeen (verzamelniveau)

13.11 vloeren op grondslag; niet constructief, bodemafsluitingen

13.12 vloeren op grondslag; niet constructief, vloeren als gebouwonderdeel

13.13 vloeren op grondslag; niet constructief, vloeren als bestrating

13.20 vloeren op grondslag; constructief, algemeen (verzamelniveau)

13.21 vloeren op grondslag; constructief, bodemafsluitingen

13.22 vloeren op grondslag; constructief, vloeren als gebouwonderdeel

13.25 vloeren op grondslag; constructief, grondverbeteringen

16 funderingsconstructies

16.10 funderingsconstructies; voeten en balken, algemeen (verzamelniveau)

16.11 funderingsconstructies; voeten en balken, fundatie voeten

16.12 funderingsconstructies; voeten en balken, fundatie balken

16.13 funderingsconstructies; voeten en balken, fundatie poeren

16.14 funderingsconstructies; voeten en balken, gevelwanden (-200)

16.15 funderingsconstructies; voeten en balken, grondverbeteringen

16.20 funderingsconstructies; keerwanden, algemeen (verzamelniveau)

16.21 funderingsconstructies; keerwanden, grondkerende wanden

16.22 funderingsconstructies; keerwanden, waterkerende wanden

16.23 funderingsconstructies; keerwanden, gevelwanden (-200)

16.25 funderingsconstructies; keerwanden, grondverbeteringen

17 paalfunderingen

17.10 paalfunderingen; niet geheid, algemeen (verzamelniveau)

17.11 paalfunderingen; niet geheid, dragend palen; geboord

17.12 paalfunderingen; niet geheid, dragende palen; geschroefd

17.13 paalfunderingen; niet geheid, trekverankeringen

17.14 paalfunderingen; niet geheid, pijler-putring-funderingen

17.15 paalfunderingen; niet geheid, bodeminjecties

17.20 paalfunderingen; geheid, algemeen (verzamelniveau)

17.21 paalfunderingen; geheid, dragende palen

17.22 paalfunderingen; geheid, palen; ingeheide bekisting

17.23 paalfunderingen; geheid, trekverankeringen

17.25 paalfunderingen; geheid, damwanden-funderingen

Page 43: de werkwijze en open standaarden

2- RUWBOUW

21 buitenwanden

21.10 buitenwanden; niet constructief, algemeen (verzamelniveau)

21.11 buitenwanden; niet constructief, massieve wanden

21.12 buitenwanden; niet constructief, spouwwanden

21.13 buitenwanden; niet constructief, systeemwanden

21.14 buitenwanden; niet constructief, vlieswanden

21.15 buitenwanden; niet constructief, borstweringen

21.16 buitenwanden; niet constructief, boeiboorden

21.20 buitenwanden; constructief, algemeen (verzamelniveau)

21.21 buitenwanden; constructief, massieve wanden

21.22 buitenwanden; constructief, spouwwanden

21.23 buitenwanden; constructief, systeemwanden

21.25 buitenwanden; constructief, borstweringen

22 binnenwanden

22.10 binnenwanden; niet constructief, algemeen (verzamelniveau)

22.11 binnenwanden; niet constructief, massieve wanden

22.12 binnenwanden; niet constructief, spouwwanden

22.13 binnenwanden; niet constructief, systeemwanden; vast

22.14 binnenwanden; niet constructief, systeemwanden; verplaatsbaar

22.20 binnenwanden; constructief, algemeen (verzamelniveau)

22.21 binnenwanden; constructief, massieve wanden

22.22 binnenwanden; constructief, spouwwanden

22.23 binnenwanden; constructief, systeemwanden; vast

23 vloeren

23.10 vloeren; niet constructief, algemeen (verzamelniveau)

23.11 vloeren; niet constructief, vrijdragende vloeren

23.12 vloeren; niet constructief, balkons

23.13 vloeren; niet constructief, galerijen

23.14 vloeren; niet constructief, bordessen

23.15 vloeren; niet constructief, vloeren t.b.v. technische voorzieningen

23.20 vloeren; constructief, algemeen (verzamelniveau)

23.21 vloeren; constructief, vrijdragende vloeren

23.22 vloeren; constructief, balkons

23.23 vloeren; constructief, galerijen

23.24 vloeren; constructief, bordessen

23.25 vloeren; constructief, vloeren t.b.v. technische voorzieningen

24 trappen en hellingen

24.10 trappen en hellingen; trappen, algemeen (verzamelniveau)

24.11 trappen en hellingen; trappen, rechte steektrappen

24.12 trappen en hellingen; trappen, niet-rechte steektrappen

24.13 trappen en hellingen; trappen, spiltrappen

24.15 trappen en hellingen; trappen, bordessen

Page 44: de werkwijze en open standaarden

24.20 trappen en hellingen; hellingen, algemeen (verzamelniveau)

24.21 trappen en hellingen; hellingen, beloopbare hellingen

24.22 trappen en hellingen; hellingen, berijdbare hellingen

24.25 trappen en hellingen; hellingen, bordessen

24.30 trappen en hellingen; ladders en klimijzers, algemeen (verzamelniveau)

24.31 trappen en hellingen; ladders en klimijzers, ladders

24.32 trappen en hellingen; ladders en klimijzers, klimijzers

24.35 trappen en hellingen; ladders en klimijzers, bordessen

27 daken

27.10 daken; niet constructief, algemeen (verzamelniveau)

27.11 daken; niet constructief, vlakke daken

27.12 daken; niet constructief, hellende daken

27.13 daken; niet constructief, luifels

27.14 daken; niet constructief, overkappingen

27.16 daken; niet constructief, gootconstructies

27.20 daken; constructief, algemeen (verzamelniveau)

27.21 daken; constructief, vlakke daken

27.22 daken; constructief, hellende daken

27.23 daken; constructief, luifels

27.24 daken; constructief, overkappingen

27.26 daken; constructief, gootconstructies

28 hoofddraagconstructies

28.10 hoofddraagconstructies; kolommen en liggers, algemeen (verzamelniveau)

28.11 hoofddraagconstructies; kolommen en liggers, kolom-/liggerconstructies

28.12 hoofddraagconstructies; kolommen en liggers, spanten

28.20 hoofddraagconstructies; wanden en vloeren, algemeen (verzamelniveau)

28.21 hoofddraagconstructies; wanden en vloeren, wand-/vloerconstructies

28.30 hoofddraagconstructies; ruimte-eenheden, algemeen (verzamelniveau)

28.31 hoofddraagconstructies; ruimte-eenheden, doosconstructies

3- AFBOUW

31 buitenwandopeningen

31.10 buitenwandopeningen; niet gevuld, algemeen (verzamelniveau)

31.11 buitenwandopeningen; niet gevuld, daglichtopeningen

31.12 buitenwandopeningen; niet gevuld, buitenluchtopeningen

31.20 buitenwandopeningen; gevuld met ramen, algemeen (verzamelniveau)

31.21 buitenwandopeningen; gevuld met ramen, gesloten ramen

31.22 buitenwandopeningen; gevuld met ramen, ramen draaiend aan een kant

31.23 buitenwandopeningen; gevuld met ramen, schuiframen

31.24 buitenwandopeningen; gevuld met ramen, ramen draaiend op verticale of horizontale as

31.25 buitenwandopeningen; gevuld met ramen, combinatieramen

31.30 buitenwandopeningen; gevuld met deuren, algemeen (verzamelniveau)

31.31 buitenwandopeningen; gevuld met deuren, draaideuren

31.32 buitenwandopeningen; gevuld met deuren, schuifdeuren

31.33 buitenwandopeningen; gevuld met deuren, tuimeldeuren

31.34 buitenwandopeningen; gevuld met deuren, tourniqets

Page 45: de werkwijze en open standaarden

31.40 buitenwandopeningen; gevuld met puien, algemeen (verzamelniveau)

31.41 buitenwandopeningen; gevuld met puien, gesloten puien

32 binnenwandopeningen

32.10 binnenwandopeningen; niet gevuld, algemeen (verzamelniveau)

32.11 binnenwandopeningen; niet gevuld, openingen als doorgang

32.12 binnenwandopeningen; niet gevuld, openingen als doorzicht

32.20 binnenwandopeningen; gevuld met ramen, algemeen (verzamelniveau)

32.21 binnenwandopeningen; gevuld met ramen, gesloten ramen

32.22 binnenwandopeningen; gevuld met ramen, ramen draaiend aan een kant

32.23 binnenwandopeningen; gevuld met ramen, schuiframen

32.24 binnenwandopeningen; gevuld met ramen, ramen draaiend op verticale of horizontale as

32.25 binnenwandopeningen; gevuld met ramen, combinatieramen

32.30 binnenwandopeningen; gevuld met deuren, algemeen (verzamelniveau)

32.31 binnenwandopeningen; gevuld met deuren, draaideuren

32.32 binnenwandopeningen; gevuld met deuren, schuifdeuren

32.33 binnenwandopeningen; gevuld met deuren, tuimeldeuren

32.34 binnenwandopeningen; gevuld met deuren, tourniqets

32.40 binnenwandopeningen; gevuld met puien, algemeen (verzamelniveau)

32.41 binnenwandopeningen; gevuld met puien, gesloten puien

33 vloeropeningen

33.10 vloeropeningen; niet gevuld, algemeen (verzamelniveau)

33.11 vloeropeningen; niet gevuld, openingen als doorgang

33.12 vloeropeningen; niet gevuld, openingen als doorzicht

33.20 vloeropeningen; gevuld, algemeen (verzamelniveau)

33.21 vloeropeningen; gevuld, beloopbare vullingen

33.22 vloeropeningen; gevuld, niet-beloopbare vullingen

34 balustrades en leuningen

34.10 balustrades en leuningen; balustrades, algemeen (verzamelniveau)

34.11 balustrades en leuningen; balustrades, binnenbalustrades

34.12 balustrades en leuningen; balustrades, buitenbalustrades

34.20 balustrades en leuningen; leuningen, algemeen (verzamelniveau)

34.21 balustrades en leuningen; leuningen, binnenleuningen

34.22 balustrades en leuningen; leuningen, buitenleuningen

37 dakopeningen

37.10 dakopeningen; niet gevuld, algemeen (verzamelniveau)

37.11 dakopeningen; niet gevuld, daglichtopeningen

37.12 dakopeningen; niet gevuld, buitenluchtopeningen

37.20 dakopeningen; gevuld, algemeen (verzamelniveau)

37.21 dakopeningen; gevuld, gesloten ramen

37.22 dakopeningen; gevuld, ramen draaiend aan één kant

37.23 dakopeningen; gevuld, schuiframen

37.24 dakopeningen; gevuld, ramen draaiend op een as

37.25 dakopeningen; gevuld, combinatieramen

38 inbouwpakketten

Page 46: de werkwijze en open standaarden

38.10 inbouwpakketten; algemeen (verzamelniveau)

38.11 inbouwpakketten; inbouwpakketten met te openen delen

38.12 inbouwpakketten; inbouwpakketten met gesloten delen

4- AFWERKINGEN

41 buitenwandafwerkingen

41.10 buitenwandafwerkingen; algemeen (verzamelniveau)

41.11 buitenwandafwerkingen; afwerklagen

41.12 buitenwandafwerkingen; bekledingen

41.13 buitenwandafwerkingen; voorzetwanden

42 binnenwandafwerkingen

42.10 binnenwandafwerkingen; algemeen (verzamelniveau)

42.11 binnenwandafwerkingen; afwerklagen

42.12 binnenwandafwerkingen; bekledingen

43 vloerafwerkingen

43.10 vloerafwerkingen; verhoogd, algemeen (verzamelniveau)

43.11 vloerafwerkingen; verhoogd, podiums

43.12 vloerafwerkingen; verhoogd, installatievloeren

43.20 vloerafwerkingen; niet verhoogd, algemeen (verzamelniveau)

43.21 vloerafwerkingen; niet verhoogd, afwerklagen

43.22 vloerafwerkingen; niet verhoogd, bekledingen

43.23 vloerafwerkingen; niet verhoogd, systeemvloerafwerkingen

44 trap- en hellingafwerkingen

44.10 trap- en hellingafwerkingen; trapafwerkingen, algemeen (verzamelniveau)

44.11 trap- en hellingafwerkingen; trapafwerkingen, afwerklagen

44.12 trap- en hellingafwerkingen; trapafwerkingen, bekledingen

44.13 trap- en hellingafwerkingen; trapafwerkingen, systeemafwerkingen

44.20 trap- en hellingafwerkingen; hellingafwerkingen, algemeen (verzamelniveau)

44.21 trap- en hellingafwerkingen; hellingafwerkingen, afwerklagen

44.22 trap- en hellingafwerkingen; hellingafwerkingen, bekledingen

44.23 trap- en hellingafwerkingen; hellingafwerkingen, systeemafwerkingen

45 plafondafwerkingen

45.10 plafondafwerkingen; verlaagd, algemeen (verzamelniveau)

45.11 plafondafwerkingen; verlaagd, verlaagde plafonds

45.12 plafondafwerkingen; verlaagd, systeem plafonds

45.14 plafondafwerkingen; verlaagd, koofconstructies

45.15 plafondafwerkingen; verlaagd, gordijnplanken

45.20 plafondafwerkingen; niet verlaagd, algemeen (verzamelniveau)

45.21 plafondafwerkingen; niet verlaagd, afwerkingen

45.22 plafondafwerkingen; niet verlaagd, bekledingen

45.23 plafondafwerkingen; niet verlaagd, systeemafwerkingen

45.24 plafondafwerkingen; niet verlaagd, koofconstructies

45.25 plafondafwerkingen; niet verlaagd, gordijnplanken

47 dakafwerkingen

Page 47: de werkwijze en open standaarden

47.10 dakafwerkingen; afwerkingen, algemeen (verzamelniveau)

47.11 dakafwerkingen; afwerkingen, vlakke dakafwerkingen

47.12 dakafwerkingen; afwerkingen, hellende dakafwerkingen

47.13 dakafwerkingen; afwerkingen, luifel afwerkingen

47.14 dakafwerkingen; afwerkingen, overkappings afwerkingen

47.15 dakafwerkingen; afwerkingen, beloopbare dakafwerkingen

47.16 dakafwerkingen; afwerkingen, berijdbare dakafwerkingen

47.20 dakafwerkingen; bekledingen, algemeen (verzamelniveau)

47.21 dakafwerkingen; bekledingen, vlakke bekledingen

47.22 dakafwerkingen; bekledingen, hellende bekledingen

47.23 dakafwerkingen; bekledingen, luifel bekledingen

47.24 dakafwerkingen; bekledingen, overkapping bekledingen

47.25 dakafwerkingen; bekledingen, beloopbare dak bekledingen

47.26 dakafwerkingen; bekledingen, berijdbare dak bekledingen

48 afwerkingspakketten

48.10 afwerkingspakketten; algemeen (verzamelniveau)

48.11 afwerkingspakketten; naadloze afwerkingen

48.12 afwerkingspakketten; overige afwerkingen

5- INSTALLATIES WERKTUIGBOUWKUNDIG

51 warmte-opwekking

51.10 warmte-opwekking; lokaal, algemeen (verzamelniveau)

51.11 warmte-opwekking; lokaal, gasvormige brandstoffen

51.12 warmte-opwekking; lokaal, vloeibare brandstoffen

51.13 warmte-opwekking; lokaal, vaste brandstoffen

51.14 warmte-opwekking; lokaal, schoorstenen/kanalen (niet bouwkundig)

51.16 warmte-opwekking; lokaal, gecombineerde tapwaterverwarming

51.19 warmte-opwekking; lokaal, brandstoffenopslag

51.20 warmte-opwekking; centraal, algemeen (verzamelniveau)

51.21 warmte-opwekking; centraal, gasvormige brandstoffen

51.22 warmte-opwekking; centraal, vloeibare brandstoffen

51.23 warmte-opwekking; centraal, vaste brandstoffen

51.24 warmte-opwekking; centraal, schoorstenen/kanalen (niet bouwkundig)

51.26 warmte-opwekking; centraal, gecombineerde tapwater verwarming

51.29 warmte-opwekking; centraal, brandstoffenopslag

51.30 warmte-opwekking; toegeleverde warmte, algemeen (verzamelniveau)

51.31 warmte-opwekking; toegeleverde warmte, water tot 140° C.

51.32 warmte-opwekking; toegeleverde warmte, water boven 140° C.

51.33 warmte-opwekking; toegeleverde warmte, stoom

51.36 warmte-opwekking; toegeleverde warmte, gecombineerde tapwaterverwarming

51.40 warmte-opwekking; warmte-krachtkoppeling, algemeen (verzamelniveau)

51.41 warmte-opwekking; warmte-krachtkoppeling, total-energy

51.44 warmte-opwekking; warmte-krachtkoppeling, schoorstenen/kanalen (niet bouwkundig)

51.46 warmte-opwekking; warmte-krachtkoppeling, gecombineerde tapwaterverwarming

51.49 warmte-opwekking; warmte-krachtkoppeling, brandstoffenopslag

51.50 warmte-opwekking; bijzonder, algemeen (verzamelniveau)

Page 48: de werkwijze en open standaarden

51.51 warmte-opwekking; bijzonder, warmtepomp

51.52 warmte-opwekking; bijzonder, zonnecollectoren

51.53 warmte-opwekking; bijzonder, accumulatie

51.54 warmte-opwekking; bijzonder, aardwarmte

51.55 warmte-opwekking; bijzonder, kernenergie

52 afvoeren

52.10 afvoeren; regenwater, algemeen (verzamelniveau)

52.11 afvoeren; regenwater, afvoerinstallatie; in het gebouw

52.12 afvoeren; regenwater, afvoerinstallatie; buiten het gebouw

52.16 afvoeren; regenwater, pompsysteem

52.20 afvoeren; fecaliën, algemeen (verzamelniveau)

52.21 afvoeren; fecaliën, standaard systeem

52.22 afvoeren; fecaliën, vacuümsysteem

52.23 afvoeren; fecaliën, overdruksysteem

52.26 afvoeren; fecaliën, pompsysteem

52.30 afvoeren; afvalwater, algemeen (verzamelniveau)

52.31 afvoeren; afvalwater, huishoudelijk afval

52.32 afvoeren; afvalwater, bedrijfsafval

52.36 afvoeren; afvalwater, pompsysteem

52.40 afvoeren; gecombineerd, algemeen (verzamelniveau)

52.41 afvoeren; gecombineerd, geïntegreerd systeem

52.46 afvoeren; gecombineerd, pompsysteem

52.50 afvoeren; speciaal, algemeen (verzamelniveau)

52.51 afvoeren; speciaal, chemisch verontreinigd afvalwater

52.52 afvoeren; speciaal, biologisch besmet afvalwater

52.53 afvoeren; speciaal, radioactief besmet afvalwater

52.56 afvoeren; speciaal, pompsysteem

52.60 afvoeren; vast vuil, algemeen (verzamelniveau)

52.61 afvoeren; vast vuil, stortkokers

52.62 afvoeren; vast vuil, vacuümsysteem

52.63 afvoeren; vast vuil, persluchtsysteem

52.64 afvoeren; vast vuil, verdichtingssysteem

52.65 afvoeren; vast vuil, verbrandingssysteem

53 water

53.10 water; drinkwater, algemeen (verzamelniveau)

53.11 water; drinkwater, netaansluiting

53.12 water; drinkwater, bronaansluiting

53.13 water; drinkwater, reinwaterkelderaansluiting

53.14 water; drinkwater, drukverhoging

53.19 water; drinkwater, opslagtanks

53.20 water; verwarmd tapwater, algemeen (verzamelniveau)

53.21 water; verwarmd tapwater, direct verwarmd met voorraad

53.22 water; verwarmd tapwater, indirect verwarmd met voorraad

53.23 water; verwarmd tapwater, doorstroom; direct verwarmd

53.24 water; verwarmd tapwater, doorstroom; indirect verwarmd

53.30 water; bedrijfswater, algemeen (verzamelniveau)

53.31 water; bedrijfswater, onthard-watersysteem

Page 49: de werkwijze en open standaarden

53.32 water; bedrijfswater, demi-watersysteem

53.33 water; bedrijfswater, gedistilleerd-watersysteem

53.34 water; bedrijfswater, zwembad-watersysteem

53.40 water; gebruiksstoom en condens, algemeen (verzamelniveau)

53.41 water; gebruiksstoom en condens, lage-druk stoomsysteem

53.42 water; gebruiksstoom en condens, hoge-druk stoomsysteem

53.44 water; gebruiksstoom en condens, condens verzamelsysteem

53.50 water; waterbehandeling, algemeen (verzamelniveau)

53.51 water; waterbehandeling, filtratiesysteem

53.52 water; waterbehandeling, absorptiesysteem

53.53 water; waterbehandeling, ontgassingsysteem

53.54 water; waterbehandeling, destillatiesysteem

54 gassen

54.10 gassen; brandstof, algemeen (verzamelniveau)

54.11 gassen; brandstof, aardgasvoorziening

54.12 gassen; brandstof, butaanvoorziening

54.13 gassen; brandstof, propaanvoorziening

54.14 gassen; brandstof, LPG-voorziening

54.20 gassen; perslucht en vacuüm, algemeen (verzamelniveau)

54.21 gassen; perslucht en vacuüm, persluchtvoorziening

54.22 gassen; perslucht en vacuüm, vacuümvoorziening

54.30 gassen; medisch, algemeen (verzamelniveau)

54.31 gassen; medisch, zuurstofvoorziening

54.32 gassen; medisch, carbogeenvoorziening

54.33 gassen; medisch, lachgasvoorziening

54.34 gassen; medisch, koolzuurvoorziening

54.35 gassen; medisch, medische luchtvoorziening

54.40 gassen; technisch, algemeen (verzamelniveau)

54.41 gassen; technisch, stikstofvoorziening

54.42 gassen; technisch, waterstofvoorziening

54.43 gassen; technisch, argonvoorziening

54.44 gassen; technisch, heliumvoorziening

54.45 gassen; technisch, acetyleenvoorziening

54.46 gassen; technisch, propaanvoorziening

54.47 gassen; technisch, koolzuurvoorziening

54.50 gassen; bijzonder, algemeen (verzamelniveau)

54.51 gassen; bijzonder, voorziening; zuivere gassen

54.52 gassen; bijzonder, voorziening; menggassen

55 koude-opwekking en distributie

55.10 koude-opwekking; lokaal, algemeen (verzamelniveau)

55.11 koude-opwekking; lokaal, raamkoelers

55.12 koude-opwekking; lokaal, splitsystemen

55.13 koude-opwekking; lokaal, compactsystemen

55.20 koude-opwekking; centraal, algemeen (verzamelniveau)

55.21 koude-opwekking; centraal, compressorensystemen

55.22 koude-opwekking; centraal, absorptiesystemen

Page 50: de werkwijze en open standaarden

55.23 koude-opwekking; centraal, grondwatersystemen

55.24 koude-opwekking; centraal, oppervlaktewatersystemen

55.30 koude-opwekking; distributie, algemeen (verzamelniveau)

55.31 koude-opwekking; distributie, distributiesystemen

56 warmtedistributie

56.10 warmtedistributie; water, algemeen (verzamelniveau)

56.11 warmtedistributie; water, radiatorsystemen

56.12 warmtedistributie; water, convectorsystemen

56.13 warmtedistributie; water, vloerverwarmingssystemen

56.20 warmtedistributie; stoom, algemeen (verzamelniveau)

56.21 warmtedistributie; stoom, radiatorsystemen

56.22 warmtedistributie; stoom, convectorsystemen

56.24 warmtedistributie; stoom, stralingspanelen

56.30 warmtedistributie; lucht, algemeen (verzamelniveau)

56.31 warmtedistributie; lucht, directe distributiesysteem

56.32 warmtedistributie; lucht, systeem met stralingsoverdracht

56.40 warmtedistributie; bijzonder, algemeen (verzamelniveau)

56.41 warmtedistributie; bijzonder, zonnewarmtesystemen

56.42 warmtedistributie; bijzonder, aardwarmtesystemen

56.43 warmtedistributie; bijzonder, centraal warmtepompsysteem

57 luchtbehandeling

57.10 luchtbehandeling; natuurlijke ventilatie, algemeen (verzamelniveau)

57.11 luchtbehandeling; natuurlijke ventilatie, voorzieningen; regelbaar

57.12 luchtbehandeling; natuurlijke ventilatie, voorzieningen; niet regelbaar

57.20 luchtbehandeling; lokale mechanische afzuiging, algemeen (verzamelniveau)

57.21 luchtbehandeling; lokale mechanische afzuiging, afzuiginstallatie

57.30 luchtbehandeling; centrale mechanische afzuiging, algemeen (verzamelniveau)

57.31 luchtbehandeling; centrale mechanische afzuiging, afzuiginstallatie

57.40 luchtbehandeling; lokale mechanische ventilatie, algemeen (verzamelniveau)

57.41 luchtbehandeling; lokale mechanische ventilatie, ventilatie-installatie

57.50 luchtbehandeling; centrale mechanische ventilatie, algemeen (verzamelniveau)

57.51 luchtbehandeling; centrale mechanische ventilatie, ventilatie-installatie

57.52 luchtbehandeling; centrale mechanische ventilatie, ventilatie-installatie met warmteterugwinning

57.60 luchtbehandeling; lokaal, algemeen (verzamelniveau)

57.61 luchtbehandeling; lokaal, luchtbehandelingsinstallatie

57.70 luchtbehandeling; centraal, algemeen (verzamelniveau)

57.71 luchtbehandeling; centraal, luchtbehandelingsinstallatie

58 regeling klimaat en sanitair

58.10 regeling klimaat en sanitair; specifieke regelingen, algemeen (verzamelniveau)

58.11 regeling klimaat en sanitair; specifieke regelingen, specifieke regeling

58.12 regeling klimaat en sanitair; specifieke regelingen, gecombineerde regeling

58.20 regeling klimaat en sanitair; centrale melding, meting en sturing, algemeen (verzamelniveau)

58.21 regeling klimaat en sanitair; centrale melding, meting en sturing, specifieke regeling

58.22 regeling klimaat en sanitair; centrale melding, meting en sturing, gecombineerde regeling

Page 51: de werkwijze en open standaarden

6- INSTALLATIES ELEKTROTECHNISCH

61 centrale electrotechnische voorzieningen

61.10 centrale elektrotechnische voorzieningen; energie, noodstroom, algemeen (verzamelniveau)

61.11 centrale elektrotechnische voorzieningen; energie, noodstroom, eigen energieopwekking

61.20 centrale elektrotechnische voorzieningen; aarding, algemeen (verzamelniveau)

61.21 centrale elektrotechnische voorzieningen; aarding, veiligheidsaarding

61.22 centrale elektrotechnische voorzieningen; aarding, medische aarding

61.23 centrale elektrotechnische voorzieningen; aarding, speciale aarding

61.24 centrale elektrotechnische voorzieningen; aarding, statische elektriciteit

61.25 centrale elektrotechnische voorzieningen; aarding, bliksemafleiding

61.26 centrale elektrotechnische voorzieningen; aarding, potentiaalvereffening

61.30 centrale elektrotechnische voorzieningen; kanalisatie, algemeen (verzamelniveau)

61.31 centrale elektrotechnische voorzieningen; kanalisatie, t.b.v. installaties voor hoge spanning

61.32 centrale elektrotechnische voorzieningen; kanalisatie, t.b.v. installaties voor lage spanning 61.33 centrale elektrotechnische voorzieningen; kanalisatie, t.b.v. installaties voor communicatie

of beveiliging

61.40 centrale elektrotechnische voorzieningen; energie, hoogspanning, algemeen

61.41 centrale elektrotechnische voorzieningen; energie, hoogspanning, 1 Kv en hoger

61.50 centrale elektrotechnische voorzieningen; energie, laagspanning, algemeen 61.51 centrale elektrotechnische voorzieningen; energie, laagspanning, lager dan 1 Kv en hoger

dan 100 V

61.60 centrale elektrotechnische voorzieningen; energie, zeer lage spanning, algemeen

61.61 centrale elektrotechnische voorzieningen; energie, zeer lage spanning, lager dan 100 V

61.70 centrale elektrotechnische voorzieningen; bliksemafleiding, algemeen

61.71 centrale elektrotechnische voorzieningen; bliksemafleiding

62 krachtstroom

62.10 krachtstroom; hoogspanning, algemeen (verzamelniveau)

62.11 krachtstroom; hoogspanning, 1 t/m 3 Kv

62.12 krachtstroom; hoogspanning, boven 3 Kv

62.20 krachtstroom; laagspanning, onbewaakt, algemeen (verzamelniveau)

62.21 krachtstroom; laagspanning, onbewaakt, 220/230 V - 380 V

62.22 krachtstroom; laagspanning, onbewaakt, 380 V - 660 V

62.23 krachtstroom; laagspanning, onbewaakt, 660 V - 1 Kv

62.30 krachtstroom; laagspanning, bewaakt, algemeen (verzamelniveau)

62.31 krachtstroom; laagspanning, bewaakt, 220/230 V - 380 V

62.32 krachtstroom; laagspanning, bewaakt, 380 V - 660 V

62.33 krachtstroom; laagspanning, bewaakt, 660 V - 1 kV

62.40 krachtstroom; laagspanning, gestabiliseerd, algemeen (verzamelniveau)

62.41 krachtstroom; laagspanning, gestabiliseerd, 220/230 V - 380 V

62.42 krachtstroom; laagspanning, gestabiliseerd, 380 V - 660 V

62.43 krachtstroom; laagspanning, gestabiliseerd, 660 V - 1 Kv

62.50 krachtstroom; laagspanning, gecompenseerd, algemeen (verzamelniveau)

62.51 krachtstroom; laagspanning, gecompenseerd, 220/230 V - 380 V

62.52 krachtstroom; laagspanning, gecompenseerd, 380 V - 660 V

62.53 krachtstroom; laagspanning, gecompenseerd, 660 V - 1 Kv

Page 52: de werkwijze en open standaarden

63 verlichting

63.10 verlichting; standaard, onbewaakt, algemeen (verzamelniveau)

63.11 verlichting; standaard, onbewaakt, 220/230 V

63.12 verlichting; standaard, onbewaakt, 115 V

63.13 verlichting; standaard, onbewaakt, 42 V

63.14 verlichting; standaard, onbewaakt, 24 V

63.20 verlichting; calamiteiten, decentraal gevoed, algemeen (verzamelniveau)

63.23 verlichting; calamiteiten, decentraal gevoed, 42 V

63.24 verlichting; calamiteiten, decentraal gevoed, 24 V

63.30 verlichting; bijzonder, onbewaakt, algemeen (verzamelniveau)

63.31 verlichting; bijzonder, onbewaakt, 220/230 V

63.32 verlichting; bijzonder, onbewaakt, 115 V

63.33 verlichting; bijzonder, onbewaakt, 42 V

63.34 verlichting; bijzonder, onbewaakt, 24 V

63.40 verlichting; standaard, bewaakt, algemeen (verzamelniveau)

63.41 verlichting; standaard, bewaakt, 220/230 V

63.42 verlichting; standaard, bewaakt, 115 V

63.43 verlichting; standaard, bewaakt, 42 V

63.44 verlichting; standaard, bewaakt, 24 V

63.50 verlichting; calamiteiten, centraal gevoed, algemeen (verzamelniveau)

63.51 verlichting; calamiteiten, centraal gevoed, 220/230 V

63.52 verlichting; calamiteiten, centraal gevoed, 115 V

63.53 verlichting; calamiteiten, centraal gevoed, 42 V

63.54 verlichting; calamiteiten, centraal gevoed, 24 V

63.60 verlichting; bijzonder, bewaakt, algemeen (verzamelniveau)

63.61 verlichting; bijzonder, bewaakt, 220/230 V

63.62 verlichting; bijzonder, bewaakt, 115 V

63.63 verlichting; bijzonder, bewaakt, 42 V

63.64 verlichting; bijzonder, bewaakt, 24 V

63.70 verlichting; reclame, algemeen (verzamelniveau)

63.71 verlichting; reclame, 220/230 V

63.72 verlichting; reclame, 115 V

63.73 verlichting; reclame, 42 V

63.74 verlichting; reclame, 24 V

63.75 verlichting; reclame, 1 Kv en hoger

64 communicatie

64.10 communicatie; overdracht van signalen, algemeen (verzamelniveau)

64.11 communicatie; overdracht van signalen, algemene signaleringen

64.12 communicatie; overdracht van signalen, algemene personenoproep

64.13 communicatie; overdracht van signalen, tijdsignalering

64.14 communicatie; overdracht van signalen, aanwezigheid-/beletsignalering

64.20 communicatie; overdracht van geluid/spraak, algemeen (verzamelniveau)

64.21 communicatie; overdracht van geluid/spraak, telefoon

64.22 communicatie; overdracht van geluid/spraak, intercom

64.23 communicatie; overdracht van geluid/spraak, radio/mobilofoon

64.24 communicatie; overdracht van geluid/spraak, geluidsdistributie

64.25 communicatie; overdracht van geluid/spraak, vertaalsystemen

Page 53: de werkwijze en open standaarden

64.26 communicatie; overdracht van geluid/spraak, conferentiesystemen

64.30 communicatie; overdracht van beelden, algemeen (verzamelniveau)

64.31 communicatie; overdracht van beelden, gesloten televisiecircuits

64.32 communicatie; overdracht van beelden, beeldreproductie

64.33 communicatie; overdracht van beelden, film/dia/overhead

64.40 communicatie; overdracht van data, algemeen (verzamelniveau)

64.41 communicatie; overdracht van data, gesloten datanet

64.42 communicatie; overdracht van data, openbaar datanet

64.50 communicatie; geïntegreerde systemen, algemeen (verzamelniveau)

64.51 communicatie; geïntegreerde systemen, gesloten netwerken

64.52 communicatie; geïntegreerde systemen, openbare netwerken

64.60 communicatie; antenne-inrichtingen, algemeen

65 beveiliging

65.10 beveiliging; brand, algemeen (verzamelniveau)

65.11 beveiliging; brand, detectie en alarmering

65.12 beveiliging; brand, deurvergrendelingen en -ontgrendelingen

65.13 beveiliging; brand, brandbestrijding

65.20 beveiliging; braak, algemeen (verzamelniveau)

65.21 beveiliging; braak, detectie en alarmering

65.22 beveiliging; braak, toegangscontrole

65.30 beveiliging; overlast, detectie en alarmering, algemeen (verzamelniveau)

65.31 beveiliging; overlast, detectie en alarmering, zonweringsinstallatie

65.32 beveiliging; overlast, detectie en alarmering, elektromagnetische voorzieningen

65.33 beveiliging; overlast, detectie en alarmering, elektromagnetische voorzieningen

65.34 beveiliging; overlast, detectie en alarmering, overspanningsbeveiliging

65.35 beveiliging; overlast, detectie en alarmering, gassenbeveiliging

65.36 beveiliging; overlast, detectie en alarmering, vloeistofbeveiliging

65.37 beveiliging; overlast, detectie en alarmering, stralingsbeveiliging

65.39 beveiliging; overlast, detectie en alarmering, overige beveiligingen

65.40 beveiliging; sociale alarmering, algemeen (verzamelniveau)

65.41 beveiliging; sociale alarmering, nooddetectie; gesloten systemen

65.42 beveiliging; sociale alarmering, nooddetectie; open systemen

65.50 beveiliging; milieu-overlast, detectie en alarmering, algemeen (verzamelniveau)

66 transport

66.10 transport; liften en heftableau's, algemeen (verzamelniveau)

66.11 transport; liften en heftableau's, elektrische liften

66.12 transport; liften en heftableau's, hydraulische liften

66.13 transport; liften en heftableau's, trapliften

66.14 transport; liften en heftableau's, heftableau's

66.20 transport; roltrappen en rolpaden, algemeen (verzamelniveau)

66.21 transport; roltrappen en rolpaden, roltrappen

66.22 transport; roltrappen en rolpaden, rolpaden

66.30 transport; goederen, algemeen (verzamelniveau)

66.31 transport; goederen, goederenliften

66.32 transport; goederen, goederenheffers

66.33 transport; goederen, baantransportmiddelen

Page 54: de werkwijze en open standaarden

66.34 transport; goederen, bandtransportmiddelen

66.35 transport; goederen, baktransportmiddelen

66.36 transport; goederen, hijswerktuigen

66.37 transport; goederen, vrije-baan-transportvoertuigen

66.40 transport; documenten, algemeen (verzamelniveau)

66.41 transport; documenten, buizenpost

66.42 transport; documenten, railcontainer banen

66.44 transport; documenten, bandtransportmiddelen

67 gebouwbeheervoorzieningen

67.10 gebouwbeheervoorzieningen; bediening en signalering, algemeen (verzamelniveau)

67.11 gebouwbeheervoorzieningen; bediening en signalering, elektrotechnische systemen

67.12 gebouwbeheervoorzieningen; bediening en signalering, optische systemen

67.13 gebouwbeheervoorzieningen; bediening en signalering, pneumatische systemen

67.14 gebouwbeheervoorzieningen; bediening en signalering, geïntegreerde systemen

67.20 gebouwbeheervoorzieningen; gebouwautomatisering, algemeen (verzamelniveau)

67.21 gebouwbeheervoorzieningen; gebouwautomatisering, elektrotechnische systemen

67.22 gebouwbeheervoorzieningen; gebouwautomatisering, optische systemen

67.23 gebouwbeheervoorzieningen; gebouwautomatisering, pneumatische systemen

67.24 gebouwbeheervoorzieningen; gebouwautomatisering, geïntegreerde systemen 67.30 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),

algemeen (verzamelniveau) 67.31 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),

elektrotechnische systemen 67.32 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),

optische systemen 67.33 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),

pneumatische systemen 67.34 gebouwbeheervoorzieningen; regelinstallaties klimaat en sanitair (op afstand),

geïntegreerde systemen

7- VASTE VOORZIENINGEN

71 vaste verkeersvoorzieningen

71.10 vaste verkeersvoorzieningen; standaard, algemeen (verzamelniveau)

71.11 vaste verkeersvoorzieningen; standaard, meubileringen

71.12 vaste verkeersvoorzieningen; standaard, bewegwijzeringen

71.13 vaste verkeersvoorzieningen; standaard, kunstwerken

71.14 vaste verkeersvoorzieningen; standaard, decoraties e.d.

71.20 vaste verkeersvoorzieningen; bijzonder, algemeen (verzamelniveau)

71.21 vaste verkeersvoorzieningen; bijzonder, meubileringen

71.22 vaste verkeersvoorzieningen; bijzonder, bewegwijzeringen

71.23 vaste verkeersvoorzieningen; bijzonder, specifieke voorz. (o.a. loopleuningen)

72 vaste gebruikersvoorzieningen

72.10 vaste gebruikersvoorzieningen; standaard, algemeen (verzamelniveau)

72.11 vaste gebruikersvoorzieningen; standaard, meubilering

72.12 vaste gebruikersvoorzieningen; standaard, lichtweringen

72.13 vaste gebruikersvoorzieningen; standaard, gordijnvoorzieningen

72.14 vaste gebruikersvoorzieningen; standaard, beschermende voorzieningen

Page 55: de werkwijze en open standaarden

72.20 vaste gebruikersvoorzieningen; bijzonder, algemeen (verzamelniveau)

72.21 vaste gebruikersvoorzieningen; bijzonder, meubilering voor specifieke functiedoeleinden

72.22 vaste gebruikersvoorzieningen; bijzonder, instrumenten/apparatuur

73 vaste keukenvoorzieningen

73.10 vaste keukenvoorzieningen; standaard, algemeen (verzamelniveau)

73.11 vaste keukenvoorzieningen; standaard, keukenmeubilering

73.12 vaste keukenvoorzieningen; standaard, keukenapparatuur

73.20 vaste keukenvoorzieningen; bijzonder, algemeen (verzamelniveau)

73.21 vaste keukenvoorzieningen; bijzonder, keukenmeubilering

73.22 vaste keukenvoorzieningen; bijzonder, keukenapparatuur

74 vaste sanitaire voorzieningen

74.10 vaste sanitaire voorzieningen; standaard, algemeen (verzamelniveau)

74.11 vaste sanitaire voorzieningen; standaard, sanitaire toestellen; normaal

74.12 vaste sanitaire voorzieningen; standaard, sanitaire toestellen; aangepast

74.13 vaste sanitaire voorzieningen; standaard, accessoires

74.20 vaste sanitaire voorzieningen; bijzonder, algemeen (verzamelniveau)

74.21 vaste sanitaire voorzieningen; bijzonder, sanitaire toestellen voor bijzondere toepassing

74.22 vaste sanitaire voorzieningen; bijzonder, ingebouwde sanitaire voorzieningen

75 vaste onderhoudsvoorzieningen

75.10 vaste onderhoudsvoorzieningen; standaard, algemeen (verzamelniveau)

75.11 vaste onderhoudsvoorzieningen; standaard, gebouwonderhoudsvoorzieningen

75.12 vaste onderhoudsvoorzieningen; standaard, interieur onderhoudsvoorzieningen

75.13 vaste onderhoudsvoorzieningen; standaard, gevelonderhoudsvoorzieningen

75.20 vaste onderhoudsvoorzieningen; bijzonder, algemeen (verzamelniveau)

75.21 vaste onderhoudsvoorzieningen; bijzonder, gebouwonderhoudsvoorzieningen

75.22 vaste onderhoudsvoorzieningen; bijzonder, interieur onderhoudsvoorzieningen

75.23 vaste onderhoudsvoorzieningen; bijzonder, gemechaniseerde gevelonderhoudsvoorzieningen

76 vaste opslagvoorzieningen

76.10 vaste opslagvoorzieningen; standaard, algemeen (verzamelniveau)

76.11 vaste opslagvoorzieningen; standaard, meubileringen

76.20 vaste opslagvoorzieningen; bijzonder, algemeen (verzamelniveau)

76.21 vaste opslagvoorzieningen; bijzonder, gemechaniseerde voorzieningen

76.22 vaste opslagvoorzieningen; bijzonder, specifieke voorzieningen

8- LOSSE INVENTARIS

81 losse verkeersinventaris

81.10 losse verkeersinventaris; standaard, algemeen (verzamelniveau)

81.11 losse verkeersinventaris; standaard, meubilering

81.12 losse verkeersinventaris; standaard, bewegwijzering

81.13 losse verkeersinventaris; standaard, kunstwerken

81.14 losse verkeersinventaris; standaard, decoraties e.d.

81.20 losse verkeersinventaris; bijzonder, algemeen (verzamelniveau)

81.21 losse verkeersinventaris; bijzonder, meubilering

81.22 losse verkeersinventaris; bijzonder, bewegwijzering

Page 56: de werkwijze en open standaarden

81.23 losse verkeersinventaris; bijzonder, specifieke voorzieningen (o.a. afvalbakken)

82 losse gebruikersinventaris

82.10 losse gebruikersinventaris; standaard, algemeen (verzamelniveau)

82.11 losse gebruikersinventaris; standaard, meubilering

82.12 losse gebruikersinventaris; standaard, lichtweringen/verduisteringen

82.13 losse gebruikersinventaris; standaard, stofferingen

82.20 losse gebruikersinventaris; bijzonder, algemeen (verzamelniveau)

82.21 losse gebruikersinventaris; bijzonder, meubilering voor specifieke functiedoeleinden

82.22 losse gebruikersinventaris; bijzonder, instrumenten/apparatuur

83 losse keukeninventaris

83.10 losse keukeninventaris; standaard, algemeen (verzamelniveau)

83.11 losse keukeninventaris; standaard, keukenmeubilering

83.12 losse keukeninventaris; standaard, keukenapparatuur

83.13 losse keukeninventaris; standaard, kleine keukeninventaris

83.20 losse keukeninventaris; bijzonder, algemeen (verzamelniveau)

83.21 losse keukeninventaris; bijzonder, keukeninrichting

83.22 losse keukeninventaris; bijzonder, keukenapparatuur

83.23 losse keukeninventaris; bijzonder, kleine keukeninventaris

83.24 losse keukeninventaris; bijzonder, transportmiddelen

84 losse sanitaire inventaris

84.10 losse sanitaire inventaris; standaard, algemeen (verzamelniveau)

84.11 losse sanitaire inventaris; standaard, afvalvoorzieningen

84.12 losse sanitaire inventaris; standaard, voorzieningen t.b.v. hygiëne

84.13 losse sanitaire inventaris; standaard, accessoires

84.20 losse sanitaire inventaris; bijzonder, algemeen (verzamelniveau)

84.21 losse sanitaire inventaris; bijzonder, sanitaire toestellen voor bijzondere toepassing

85 losse schoonmaakinventaris

85.10 losse schoonmaakinventaris; standaard, algemeen (verzamelniveau)

85.11 losse schoonmaakinventaris; standaard, schoonmaakapparatuur

85.12 losse schoonmaakinventaris; standaard, vuilopslag

85.13 losse schoonmaakinventaris; standaard, vuiltransport

85.20 losse schoonmaakinventaris; bijzonder, algemeen (verzamelniveau)

85.21 losse schoonmaakinventaris; bijzonder, schoonmaakapparatuur

85.22 losse schoonmaakinventaris; bijzonder, vuilopslag

85.23 losse schoonmaakinventaris; bijzonder, vuiltransport

86 losse opslaginventaris

86.10 losse opslaginventaris; standaard, algemeen (verzamelniveau)

86.11 losse opslaginventaris; standaard, meubileringen

86.20 losse opslaginventaris; bijzonder, algemeen (verzamelniveau)

86.21 losse opslaginventaris; bijzonder, gemechaniseerde voorzieningen

86.22 losse opslaginventaris; bijzonder, specifieke voorzieningen

Page 57: de werkwijze en open standaarden

9- TERREIN

90 terrein

90.10 terrein; grondvoorzieningen, algemeen (verzamelniveau)

90.11 terrein; grondvoorzieningen, verwijderen obstakels

90.12 terrein; grondvoorzieningen, grondwaterverlagingen

90.13 terrein; grondvoorzieningen, drainagevoorzieningen

90.20 terrein; opstallen, algemeen (verzamelniveau)

90.21 terrein; opstallen, gebouwtjes met speciale functie

90.22 terrein; opstallen, overkappingen

90.30 terrein; omheiningen, algemeen (verzamelniveau)

90.31 terrein; omheiningen, muren

90.32 terrein; omheiningen, hekwerken

90.33 terrein; omheiningen, overige afscheidingen

90.34 terrein; omheiningen, toegangen

90.40 terrein; terreinafwerkingen, algemeen (verzamelniveau)

90.41 terrein; terreinafwerkingen, verhardingen

90.42 terrein; terreinafwerkingen, beplantingen

90.43 terrein; terreinafwerkingen, waterpartijen

90.44 terrein; terreinafwerkingen, keerwanden en balustrades

90.45 terrein; terreinafwerkingen, pergola's

90.50 terrein; terreinvoorzieningen, werktuigbouwkundig, algemeen (verzamelniveau)

90.51 terrein; terreinvoorzieningen, werktuigbouwkundig, verwarmingsvoorzieningen

90.52 terrein; terreinvoorzieningen, werktuigbouwkundig, afvoervoorzieningen

90.53 terrein; terreinvoorzieningen, werktuigbouwkundig, watervoorzieningen

90.54 terrein; terreinvoorzieningen, werktuigbouwkundig, gasvoorzieningen

90.55 terrein; terreinvoorzieningen, werktuigbouwkundig, koudeopwekkingsvoorzieningen

90.56 terrein; terreinvoorzieningen, werktuigbouwkundig, warmtedistributievoorzieningen

90.57 terrein; terreinvoorzieningen, werktuigbouwkundig, luchtbehandelingsvoorzieningen

90.58 terrein; terreinvoorzieningen, werktuigbouwkundig, regelingvoorzieningen

90.60 terrein; terreinvoorzieningen, elektrotechnisch, algemeen (verzamelniveau)

90.61 terrein; terreinvoorzieningen, elektrotechnisch, elektrotechnische en aardingsvoorzieningen

90.62 terrein; terreinvoorzieningen, elektrotechnisch, krachtvoorzieningen

90.63 terrein; terreinvoorzieningen, elektrotechnisch, lichtvoorzieningen

90.64 terrein; terreinvoorzieningen, elektrotechnisch, communicatievoorzieningen

90.65 terrein; terreinvoorzieningen, elektrotechnisch, beveiligingsvoorzieningen

90.66 terrein; terreinvoorzieningen, elektrotechnisch, transportvoorzieningen

90.67 terrein; terreinvoorzieningen, elektrotechnisch, beheervoorzieningen

90.70 terrein; terreininrichtingen, standaard, algemeen (verzamelniveau)

90.71 terrein; terreininrichtingen, standaard, terreinmeubilering

90.72 terrein; terreininrichtingen, standaard, bewegwijzering

90.73 terrein; terreininrichtingen, standaard, kunstwerken

90.74 terrein; terreininrichtingen, standaard, decoraties e.d.

90.80 terrein; terreininrichtingen, bijzonder, algemeen (verzamelniveau)

90.81 terrein; terreininrichtingen, bijzonder, terreinmeubilering

90.82 terrein; terreininrichtingen, bijzonder, specifieke voorzieningen

Page 58: de werkwijze en open standaarden

90.83 terrein; terreininrichtingen, bijzonder, bijzondere verhardingen

0- INDIRECTE PROJECTVOORZIENINGEN 0-.10 indirecte projectvoorzieningen; werkterreininrichting, algemeen (verzamelniveau)

0-.11 indirecte projectvoorzieningen; werkterreininrichting, bijkomende werken

0-.12 indirecte projectvoorzieningen; werkterreininrichting, personen/materiaalvoorzieningen

0-.13 indirecte projectvoorzieningen; werkterreininrichting, energievoorzieningen

0-.14 indirecte projectvoorzieningen; werkterreininrichting, beveiligingsvoorzieningen

0-.15 indirecte projectvoorzieningen; werkterreininrichting, doorwerkvoorzieningen

0-.16 indirecte projectvoorzieningen; werkterreininrichting, voorzieningen belendende percelen

0-.17 indirecte projectvoorzieningen; werkterreininrichting, onderhoudsvoorzieningen

0-.20 indirecte projectvoorzieningen; materieelvoorzieningen, algemeen (verzamelniveau)

0-.21 indirecte projectvoorzieningen; materieelvoorzieningen, transport

0-.22 indirecte projectvoorzieningen; materieelvoorzieningen, gereedschappen

0-.30 indirecte projectvoorzieningen; risicodekking, algemeen (verzamelniveau)

0-.31 indirecte projectvoorzieningen; risicodekking, verzekeringen

0-.32 indirecte projectvoorzieningen; risicodekking, waarborgen

0-.33 indirecte projectvoorzieningen; risicodekking, prijsstijgingen

0-.40 indirecte projectvoorzieningen; projectorganisatie, algemeen (verzamelniveau)

0-.41 indirecte projectvoorzieningen; projectorganisatie, administratie

0-.42 indirecte projectvoorzieningen; projectorganisatie, uitvoering

0-.43 indirecte projectvoorzieningen; projectorganisatie, documentatie

0-.50 indirecte projectvoorzieningen; bedrijfsorganisatie, algemeen (verzamelniveau)

0-.51 indirecte projectvoorzieningen; bedrijfsorganisatie, bestuur en directie

0-.52 indirecte projectvoorzieningen; bedrijfsorganisatie, winstregelingen

Page 59: de werkwijze en open standaarden

EATC - Eindhoven

3

Page 60: de werkwijze en open standaarden

Differ - Eindhoven

3

Page 61: de werkwijze en open standaarden

a. IFC 2x3 TC1- buildingSMARTOm BIM (modellen en informatie) te kunnen delen is het noodzakelijk om een universeelbestandsformaat te kiezen. Het bestandsformaat welke door iedere BIM software in en uit kanworden gelezen is IFC (Industry Foundation Classes 2x3 TC1). IFC geeft de mogelijkheid om, netals bijvoorbeeld PDF, informatie te delen zonder dat derden de inhoud kunnen bewerken.

Omdat er naast de geometrische informatie afstemming ook technische informatie wordt gecom-municeerd, is dit wenselijk om het via de modellen te delen. Hierdoor zal het BIM daadwerkelijkals primair informatiebron gaan dienen. Om dit te kunnen doen is het belangrijk om duidelijkeafspraken en spelregels te bepalen over waar welke informatie moet komen te staan en wanneerdit in het proces moet worden gedaan.

Building SMART, de internationale organisatie achter IFC, heeft een uiteenzetting gemaakt vanobjecten en de daarbij behorende parameters. In een parameter ondervang je het soort informatiedie passend is bij het object.

Deze parameters verschillen per entiteit. BuildingSMART heeft daarin een onderverdeling gemaakt, maarheeft hieraan geen eenheden bepaalt aangezien dezevaak land of regio specifiek zijn. Building SMART heefthiervoor een site gemaakt waarop deze gehele structuurterug te vinden is (http://www.buildingsmart-tech.org/if-c/IFC2x3/TC1/html/). Wij geven een toelichting op dezestructuur om tot een werkbaar model te kunnen komen.

Termen:Entiteit: Dit is een digitale voorstelling van een elementwat voorkomt in de gebouwde omgeving. Deze entitei-ten zijn gedefinieerd en hebben specifieke eigenschappen (base quantities en property sets). Eenvoorbeeld hiervan is dat een wand een wand representeert en een deur een deur representeert.Beiden hebben verschillende maatgevende maten en eigenschappen. Er zijn entiteiten voorzowel bouwkunde, constructie als installatie techniek.

Quantity: Binnen de definities van IFC staat dat hoeveelheden die uit de vorm van een entiteit afge-leid kunnen worden niet vastgelegd zijn als gegevens van element. Deze hoeveelheden dienenuit een element berekend worden door software. Het aantal, en de verschillende soorten hoeveel-heden kan per software verschillen, in de omschrijving bij de entiteiten is gekozen om de hoeveel-heden van Solibri aan te houden.

Base Quantity: Naast de analyseerbare hoeveelheden (Quantities) zijn er ook hoeveelheden perentiteit welke standaard zijn of niet analyseerbaar zijn. Dit zijn de Base Quantities. Bij kolommenis dit bijvoorbeeld de handelslengte (nominallength). In het model is alleen de netto versie van dekolom terug te vinden. Als de geanalyseerde hoeveelheid niet overeenkomt met de vastgesteldehoeveelheid is de vastgestelde hoeveelheid leidend. Deze hoeveelheden worden door de model-leersoftware weggeschreven naar de Base Quantities.

Page 62: de werkwijze en open standaarden

Opgesteld door: Ir. J.B.F. (Jeffrey) Truijens Ing. H.J. (Jasper) de Mink

Bekijken van een IFC

Een voorbeeld van hoe de Quantities, Base Quantities en Property Sets eruit zien binnen een vande viewers (Solibri Model Viewer) is hieronder weergegeven:

Porperty set (Pset): Eigenschappen van een entiteit die niet berekend kunnen worden aan de handvan de vorm van de entiteit vallen onder properties. Per entiteit zijn er een standaard set proper-ties gedefinieerd.

Page 63: de werkwijze en open standaarden

b. Entiteiten

Overzicht entiteiten

Zoals eerder gedefinieerd is een entiteit is een digitale voorstelling van een element wat voorkomtin de gebouwde omgeving. Deze entiteiten zijn gedefinieerd en hebben specifieke eigenschappen(base quantities en property sets). Een voorbeeld van een entiteit is dat een wand een wandrepresenteert en een deur een deur representeert. Beiden hebben verschillende maatgevendematen en eigenschappen.

Er zijn 93 verschillende entiteiten binnen IFC gedefinieerd. Deze entiteiten zijn er zowel voorbouwkunde, constructie als installatie techniek. Binnen IFC zijn deze entiteiten niet gekoppeldaan een discipline en kunnen ze binnen elke discipline gebruikt worden.

Voor het gebruik van verdere analyses lichten wij de entiteiten toe waarvan de gekoppelde infor-matie het meest wordt gebruikt binnen onze processen, 20 stuks. Aan de hand van deze overzich-ten kunnen we het te verwachten informatieaanbod uit de modellen managen en eenduidig inter-preteren.

= wordt in dit document nader toegelicht

Page 64: de werkwijze en open standaarden
Page 65: de werkwijze en open standaarden

c. Quantities, Base Quantities & PsetsQuantitiesDit zijn hoeveelheden die berekend kunnen worden aan de hand van de vorm van de entiteit.Omdat bij verschillende entiteiten verschillende maten maatgevend zijn verschillen de base quan-tities ook per entiteit. Een oppervlakte van een vloer is een ander dan die van een wand.

Hoeveelheden zijn gebaseerd op de volgende hoofdanalyses:• Lengte: Dit is o.a. de basis voor length, Profile width, Profile Heigth, Bounding Box Height, Diameter, Thickness en Frame Length• Oppervlakte: Dit is o.a. de basis voor Bottom Area, Skin Area, Gross Area en Area of Openings.• Inhoud: Dit is de basis voor Volume.

Aanvullend zijn er aantal (IfcQuantityCount), gewicht (IfcQuantity-Weight) en tijd (IfcQuantityTime).

Bounding Box: Bij veel entiteiten worden de afmetingen van de boun-dingbox aangegeven. De boundingbox is de buitenwerkse maat vanhet totale element. Deze maat komt vaak overeen met de Length ofHeight van een element als dit lijkt op een basis ruimtelijke vorm(kubus, balk, cilinder) met een horizontaal of verticaal grondvlak,met een lengte die hier haaks op staat. Voor vormen die hiervanafwijken kan de boundingbox niet als leidende maat gebruiktworden.

Voorbeeld: Als een geroteerde balk de entiteit ‘object’ meekrijgt in plaats van de juiste entiteit‘beam’, is slechts het uitlezen van de hoeveelheden van de Bounding Box mogelijk. Het uitlezenvan de actual length is dus niet mogelijk.

Base QuantityHet overzicht van de base quanties is opgesteld aan de hand van de Building Smart site:http://www.buildingsmart-tech.org/ifc/IFC2x3/TC1/html/index.htm . Hier kan je meer informatievinden over de achtergrond van de Base Quantities.

Property Set (Pset)Eigenschappen van een entiteit die niet berekend kunnen worden aan de hand van de vorm vande entiteit vallen onder properties. Deze moeten dus handmatig worden toegekend. Voorbeel-den zijn: IsExternal, LoadBearing, FireRating, AcousticRating en ThermalTransmittance. Perentiteit zijn er een standaard groep properties gedefinieerd, een property set, afgekort Pset.

Sommige properties kunnen verschillend geïnterpreteerd worden, IFC schrijft hier geen eenheidin voor. Dit dient per project of entiteit worden afgesproken, gebaseerd op de informatie behoef-te.

Voorbeeld: FireRating, dit kan WBDBO of moment tot bezwijken zijn.

Actual Length

Page 66: de werkwijze en open standaarden

IfcBeamQuantities

Base Quantities

Name Description Value TypeLenght A length measure is the value of a distance Solibri analysisProfile Width The Profile Width measure is the value of a distance Solibri analysisProfile Height The Profile Height measure is the value of a distance Solibri analysisBottom Area Total area of the cross section (or profile) of the beam. The exact definition

and calculation rules depend on the method of measurement used.Solibri analysis

Volume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value TypeNominalLength Total nominal length of the beam, not taking into account any cut-out's or

other processing features.IfcQuantityLength

CrossSectionArea Total area of the cross section (or profile) of the beam. The exact definitionand calculation rules depend on the method of measurement used.

IfcQuantityArea

OuterSurfaceArea Total area of the extruded surfaces of the beam (not taking into account theend cap areas), normally generated as perimeter * length.

IfcQuantityArea

TotalSurfaceArea Total area of the beam, normally generated as perimeter * length + 2 *cross section area.

IfcQuantityArea

GrossVolume Total gross volume of the beam, not taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityVolume

NetVolume Total net volume of the beam, taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityVolume

GrossWeight Total gross weight of the beam without add-on parts, not taking intoaccount possible processing features (cut-out's, etc.) or openings andrecesses.

IfcQuantityWeight

NetWeight Total net weight of the beam without add-on parts, taking into accountpossible processing features (cut-out's, etc.) or openings and recesses.

IfcQuantityWeight

Page 67: de werkwijze en open standaarden

Pset_BeamCommon

IfcBeam

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierSpan Clear span for this object. The shape information is provided in addition to

the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.

IfcPositiveLengthMeasure / LENGTHUNIT

Slope Slope angle - relative to horizontal (0.0 degrees). The shape information isprovided in addition to the shape representation and the geometricparameters used within. In cases of inconsistency between the geometricparameters and the shape properties, provided in the attached property, thegeometric parameters take precedence.

IfcPlaneAngleMeasure/ PLANEANGLEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).

IfcBoolean

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

Page 68: de werkwijze en open standaarden

IfcColumnQuantities

Name Description Value TypeLenght A length measure is the value of a distance Solibri analysisBottom Area Total area of the cross section (or profile) of the column. The exact

definition and calculation rules depend on the method of measurementused.

Solibri analysis

Diameter A diameter is the value of a distance of a straight line going through thecenter of a circle connecting two points on the circumference.

Solibri analysis

Profile Height The Profile Height measure is the value of a distance Solibri analysisProfile Width The Profile Width measure is the value of a distance Solibri analysisSkin Area Perimeter x lenght (excl. bottom area and top area) Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 69: de werkwijze en open standaarden

Base Quantities

IfcColumn

Pset_ColumnCommon

Name Description Value TypeNominalLength Total nominal length of the column, not taking into account any cut-out's or

other processing features.IfcQuantityLength

CrossSectionArea Total area of the cross section (or profile) of the column. The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityArea

OuterSurfaceArea Total area of the extruded surfaces of the column (not taking into accountthe end cap areas), normally generated as perimeter * length.

IfcQuantityArea

TotalSurfaceArea Total area of the column, normally generated as perimeter * length + 2 *cross section area.

IfcQuantityArea

GrossVolume Total gross volume of the column, not taking into account possibleprocessing features (cut-out's, etc.) or openings and recesses. The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityVolume

NetVolume Total net volume of the column, taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityVolume

GrossWeight Total gross weight of the column without add-on parts, not taking intoaccount possible processing features (cut-out's, etc.) or openings andrecesses.

IfcQuantityWeight

NetWeight Total net weight of the column without add-on parts, taking into accountpossible processing features (cut-out's, etc.) or openings and recesses.

IfcQuantityWeight

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierSlope Slope angle - relative to horizontal (0.0 degrees). The shape information is

provided in addition to the shape representation and the geometricparameters used within. In cases of inconsistency between the geometricparameters and the shape properties, provided in the attached property, thegeometric parameters take precedence.

IfcPlaneAngleMeasure/ PLANEANGLEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).

IfcBoolean

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

Page 70: de werkwijze en open standaarden

Base Quantities

IfcCoveringQuantities

Name Description Value TypeVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value TypeGrossArea Total area of the covering in the elevation view. The exact definition and

calculation rules depend on the method of measurement used.IfcQuantityArea

NetArea Total area of the covering in the elevation view taking into accountpossible openings. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityArea

IfcPolyloop

Extruded Direction

Page 71: de werkwijze en open standaarden

IfcCoveringPset_CoveringCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety

classification.IfcLabel

AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

FlammabilityRating Flammability Rating for this object. It is given according to the nationalbuilding code that governs the rating of flammability for materials.

IfcLabel

FragilityRating Indication on the fragility of the covering (e.g., under fire conditions). It isgiven according to the national building code that might provide aclassification for fragility.

IfcLabel

SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.

IfcLabel

Material Main material of the covering, it should only be given, if no IfcMaterialclass is assigned to the IfcCovering instance.

IfcLabel

Combustible Indication whether the object is made from combustible material (TRUE) ornot (FALSE).

IfcBoolean

TotalThickness Thickness of the covering, The thickness information is provided in additionto the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.

IfcPositiveLengthMeasure / LENGTHUNIT

Finish Finish selection for this object. Here specification of the surface finish forinformational purposes

IfcText

IfcPolyloop

Extruded Direction

Page 72: de werkwijze en open standaarden

IfcCurtainWallQuantities

Name Description Value TypeArea Area of the wall as viewed by an elevation view of the middle plane. It does

take into account all wall modifications (such as openings). The exactdefinition and calculation rules depend on the method of measurementused.

Solibri analysis

Area (minimum) Other side of the same wall (see Area, often the same value) Solibri analysisGross Area Area of the wall as viewed by an elevation view of the middle plane of the

wall. It does not take into account any wall modifications (such asopenings). The exact definition and calculation rules depend on the methodof measurement used.

Solibri analysis

Gross Area (minimum) Other side of the same wall (see Gross Area, often the same value) Solibri analysisArea of Doors Area of the doors in the wall as viewed by an elevation view of the middle

plane. The exact definition and calculation rules depend on the method ofmeasurement used.

Solibri analysis

Area of Windows Area of the windows in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Area of Openings Area of the openings in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Bottom Area Total area of the cross section (or profile) of the wall. The exact definitiond l l i l d d h h d f d

Solibri analysisHeight The height measure is the value of a distance Solibri analysisHeight (minimum) Lower side of the same wall (see Height, often the same value) Solibri analysisLength A length measure is the value of a distance Solibri analysisLength (minimum) Shorter side of the same wall (see Length, often the same value) Solibri analysisThickness The thickness measure is the value of a distance Solibri analysisThickness (minimum) Thinner side of the same wall (see Thickness, often the same value) Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 73: de werkwijze en open standaarden

Base Quantities

IfcCurtainWall

Pset_CurtainWallCommonName Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierAcousticRating Acoustic rating for this object. It is giving according to the national building

code. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

FireRating Fire rating given according to the national fire safety classification. IfcLabelCombustible Indication whether the object is made from combustible material (TRUE) or

not (FALSE).IfcBoolean

SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.

IfcLabel

ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. Here the totalthermal transmittance coefficient through the wall (including all materials).

IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

Name Description Value Type

Page 74: de werkwijze en open standaarden

IfcDoorQuantities

Base Quantities

Name Description Value Type

Name Description Value TypeArea Total area of the door in the elevation view. The exact definition and

calculation rules depend on the method of measurement used.Solibri analysis

Height The height measure is the value of a distance Solibri analysisWidth The width measure is the value of a distance Solibri analysisFrame Length A length measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 75: de werkwijze en open standaarden

Pset_DoorCommon

IfcDoor

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety

classification.IfcLabel

AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

SecurityRating Index based rating system indicating security level. It is giving according tothe national building code.

IfcLabel

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

Infiltration Infiltration flowrate of outside air for the filler object based on the area ofthe filler object at a pressure level of 50 Pascals. It shall be used, if thelength of all joints is unknown.

IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT

ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. It applies to thetotal door construction.

IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT

GlazingAreaFraction Fraction of the glazing area relative to the total area of the filling element.It shall be used, if the glazing area is not given separately for all panelswithin the filling element.

IfcPositiveRatioMeasure

HandicapAccessible Indication that this object is designed to be accessible by the handicapped.It is giving according to the requirements of the national building code.

IfcBoolean

FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here it defines an exit door in accordance to thenational building code.

IfcBoolean

SelfClosing Indication whether this object is designed to close automatically after use(TRUE) or not (FALSE).

IfcBoolean

SmokeStop Indication whether the object is designed to provide a smoke stop (TRUE)or not (FALSE).

IfcBoolean

Page 76: de werkwijze en open standaarden

IfcFootingQuantities

Base Quantities

Name Description Value Type

Name Description Value TypeHeight The height measure is the value of a distance Solibri analysisBottom Area Total area of the cross section (or profile) of the footing. The exact

definition and calculation rules depend on the method of measurementused.

Solibri analysis

Profile Height The Profile Height measure is the value of a distance Solibri analysisProfile Width The Profile Width measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 77: de werkwijze en open standaarden

Pset_ReinforcementBarCountOfIndependentFooting,Pset_ReinforcementBarPitchOfContinuousFooting

IfcFooting

Name Definition Data Type

Description Description of the reinforcement. IfcTextReference A descriptive label for the general reinforcement type. IfcLabelXDirectionLowerBarCount The number of bars with X direction lower bar. IfcIntegerYDirectionLowerBarCount The number of bars with Y direction lower bar. IfcIntegerXDirectionUpperBarCount The number of bars with X direction upper bar. IfcIntegerYDirectionUpperBarCount The number of bars with Y direction upper bar. IfcInteger

Description Description of the reinforcement. IfcTextReference A descriptive label for the general reinforcement type. IfcLabelCrossingUpperBarPitch The pitch length of the crossing upper bar. IfcPositiveLengthMeas

ure / LENGTHUNITCrossingLowerBarPitch The pitch length of the crossing lower bar. IfcPositiveLengthMeas

ure / LENGTHUNIT

Pset_ReinforcementBarCountOfIndependentFooting

Pset_ReinforcementBarPitchOfContinuousFooting

Page 78: de werkwijze en open standaarden

IfcMemberQuantities

Base Quantities

Name Description Value TypeVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value TypeNominalLength Total nominal length of the member, not taking into account any cut-out's

or other processing features.IfcQuantityLength

CrossSectionArea Total area of the cross section (or profile) of the member. The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityArea

OuterSurfaceArea Total area of the extruded surfaces of the member (not taking into accountthe end cap areas), normally generated as perimeter * length.

IfcQuantityArea

TotalSurfaceArea Total area of the member, normally generated as perimeter * length + 2 *cross section area.

IfcQuantityArea

GrossVolume Total gross volume of the member, not taking into account possibleprocessing features (cut-out's, etc.) or openings and recesses. The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityVolume

NetVolume Total net volume of the member, taking into account possible processingfeatures (cut-out's, etc.) or openings and recesses. The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityVolume

GrossWeight Total gross weight of the member without add-on parts, not taking intoaccount possible processing features (cut-out's, etc.) or openings andrecesses.

IfcQuantityWeight

NetWeight Total net weight of the member without add-on parts, taking into accountpossible processing features (cut-out's, etc.) or openings and recesses.

IfcQuantityWeight

Page 79: de werkwijze en open standaarden

Pset_MemberCommon

IfcMember

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierSpan Clear span for this object. The shape information is provided in addition to

the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.

IfcPositiveLengthMeasure / LENGTHUNIT

Slope Slope angle - relative to horizontal (0.0 degrees). The shape information isprovided in addition to the shape representation and the geometricparameters used within. In cases of inconsistency between the geometricparameters and the shape properties, provided in the attached property, thegeometric parameters take precedence.

IfcPlaneAngleMeasure/ PLANEANGLEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).

IfcBoolean

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

Page 80: de werkwijze en open standaarden
Page 81: de werkwijze en open standaarden

IfcObjectQuantities

Base Quantities

Pset_BuildingElementProxyCommon

Name Description Value TypeBottom Area Total area of the cross section (or profile) of the object. The exact definition

and calculation rules depend on the method of measurement used.Solibri analysis

Volume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifier

Name Description Value Type

Page 82: de werkwijze en open standaarden

IfcOpeningQuantities

Base Quantities

Name Description Value TypeArea Total area of the opening in the elevation view. The exact definition and

calculation rules depend on the method of measurement used.Solibri analysis

Height The height measure is the value of a distance Solibri analysisWidth The width measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value TypeNominalArea Area of the opening as viewed by an elevation view (for wall openings) or

as viewed by a ground floor view (for floor openings). The exact definitionand calculation rules depend on the method of measurement used.

IfcQuantityArea

NominalVolume Volume of the opening. The exact definition and calculation rules depend onthe method of measurement used.

IfcQuantityVolume

Page 83: de werkwijze en open standaarden

IfcOpeningPset_OpeningElementCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierPurpose Indication of the purpose for that opening, e.g. 'ventilation', 'access', etc. IfcLabelFireExit Indication whether this object is designed to serve as an exit in the case of

fire (TRUE) or not (FALSE). Here whether the space (in case of e.g., acorridor) is designed to serve as an exit space, e.g., for fire escapepurposes.

IfcBoolean

ProtectedOpening Indication whether the opening is considered to be protected under firesafety considerations. If (TRUE) it counts as a protected opening under theapplicable building code, (FALSE) otherwise.

IfcBoolean

ParallelJambs Indicated, whether the jambs of an opening in a curved building elementare intended to be parallel (TRUE) or are radial (FALSE). Radial means, thatthe extension of the jambs are rays through the axis of the revolutionforming the curved building element.

IfcBoolean

Page 84: de werkwijze en open standaarden

Pset_PlateCommon

IfcPlateQuantities

Base Quantities

Name Description Value TypeVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value Type

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierIsExternal Indication whether the element is designed for use in the exterior (TRUE)

or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).

IfcBoolean

AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. It applies to thetotal door construction.

IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT

Extruded Direction

Page 85: de werkwijze en open standaarden

Pset_RailingCommon

IfcRailingQuantities

Base QuantitiesName Description Value Type

Name Description Value TypeBottom Area Total area of the cross section (or profile) of the railing. The exact

definition and calculation rules depend on the method of measurementused.

Solibri analysis

Height The Height measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierHeight Height of the object. It is the upper hight of the railing above the floor or

stair. The size information is provided in addition to the shaperepresentation and the geometric parameters used within. In cases ofinconsistency between the geometric parameters and the size properties,provided in the attached property set, the geometric parameters takeprecedence.

IfcPositiveLengthMeasure / LENGTHUNIT

Diameter Diameter of the object. It is the diameter of the handrail of the railing. Thesize information is provided in addition to the shape representation and thegeometric parameters used within. In cases of inconsistency between thegeometric parameters and the size properties, provided in the attachedproperty set, the geometric parameters take precedence. Here the diameterof the hand or guardrail within the railing.

IfcPositiveLengthMeasure / LENGTHUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

Page 86: de werkwijze en open standaarden

IfcRampQuantities

Base QuantitiesName Description Value Type

Name Description Value TypeBottom Area Total area of the cross section (or profile) of the ramp. The exact definition

and calculation rules depend on the method of measurement used.Solibri analysis

Volume A volume measure is the value of the solid content of a body Solibri analysisHeight The height measure is the value of a distance Solibri analysisAngle Angle of the object - relative to horizontal (0.0 degrees) Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 87: de werkwijze en open standaarden

IfcRampPset_RampCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierRequiredHeadroom Required headroom clearance for the passageway according to the

applicable building code or additional requirements.IfcPositiveLengthMeasure / LENGTHUNIT

RequiredSlope Required sloping angle of the object - relative to horizontal (0.0 degrees).Required maximum slope for the passageway according to the applicablebuilding code or additional requirements

IfcPlaneAngleMeasure/ PLANEANGLEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here it defines an exit ramp in accordance tothe national building code.

IfcBoolean

HandicapAccessible Indication that this object is designed to be accessible by the handicapped.Set to (TRUE) if this ramp is rated as handicap accessible according thelocal building codes, otherwise (FALSE).

IfcBoolean

HasNonSkidSurface Indication whether the surface finish is designed to prevent slippery (TRUE)or not (FALSE).

IfcBoolean

Page 88: de werkwijze en open standaarden

IfcRoofQuantities

Base Quantities

Name Description Value TypeArea Total area of the roof in the elevation view taking into account

possible openings. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Perimeter The perimeter measure is the value of a distance Solibri analysisThickness The thickness measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value TypeTotalSurfaceArea Total (exposed to the outside) area of all roof slabs belonging to the roof.

The exact definition and calculation rules depend on the method ofmeasurement used.

IfcQuantityArea

LocalPlacements of IfcSlab

LocalPlacements of IfcRoof

Page 89: de werkwijze en open standaarden

IfcRoofPset_RoofCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety

classification.IfcLabel

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

ProjectedArea Area of the roof projected onto a 2D horizontal plane IfcAreaMeasure /AREAUNIT

TotalArea Total exposed area of the roof IfcAreaMeasure /AREAUNIT

LocalPlacements of IfcSlab

LocalPlacements of IfcRoof

Page 90: de werkwijze en open standaarden

IfcSlabQuantities

Name Description Value TypeArea Total area of the extruded area of the slab, taking into account possible

slab openings. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Gross Area Total area of the extruded area of the slab. The exact definition andcalculation rules depend on the method of measurement used.

Solibri analysis

Area of Openings Total area of openings. Solibri analysisPerimeter The perimeter measure of the slab is the value of a distance Solibri analysisPerimeter of Openings The perimeter measure of the openings in the slab is the value of a

distanceSolibri analysis

Thickness The thickness measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Extruded Direction

Page 91: de werkwijze en open standaarden

IfcSlab

Pset_SlabCommon

Base Quantities

Name Description Value TypeNominalWidth Total nominal (or average) width (or thickness) of the slab. The exact

definition and calculation rules depend on the method of measurementused.

IfcQuantityLength

Perimeter Perimeter measured along the outer boundaries of the slab. The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityLength

GrossArea Total area of the extruded area of the slab. The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityArea

NetArea Total area of the extruded area of the slab, taking into account possibleslab openings. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityArea

GrossVolume Total gross volume of the slab, not taking into account possible openingsand recesses. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityVolume

NetVolume Total net volume of the slab, taking into account possible openings andrecesses. The exact definition and calculation rules depend on the methodof measurement used.

IfcQuantityVolume

GrossWeight Total gross weight of the slab, not taking into account possible openingsand recesses or projections. The exact definition and calculation rulesdepend on the method of measurement used.

IfcQuantityWeight

NetWeight Total net weight of the slab, taking into account possible openings andrecesses or projections. The exact definition and calculation rules dependon the method of measurement used.

IfcQuantityWeight

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierAcousticRating Acoustic rating for this object. It is giving according to the national building

code. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values

IfcLabel

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

Combustible Indication whether the object is made from combustible material (TRUE) ornot (FALSE).

IfcBoolean

SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.

IfcLabel

ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. Here the totalthermal transmittance coefficient through the slab (including all materials).

IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building

IfcBoolean

LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).

IfcBoolean

Compartmentation Indication whether the object is designed to serve as a firecompartmentation (TRUE) or not (FALSE).

IfcBoolean

PitchAngle Angle of the slab to the horizontal when used as a component for the roof(specified as 0 degrees or not asserted for cases where the slab is not usedas a roof component).

IfcPlaneAngleMeasure/ PLANEANGLEUNIT

Extruded Direction

Page 92: de werkwijze en open standaarden

IfcSpaceQuantities

Name Description Value TypeArea Total area of the extruded area of the space, taking into account possible

space openings. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Height The height measure is the value of a distance Solibri analysisPerimeter The perimeter measure of the space is the value of a distance Solibri analysisArea of Doors Total area of doors Solibri analysisArea of Windows Total area of windows Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 93: de werkwijze en open standaarden

IfcSpaceBase Quantities

Name Description Value TypeNominalHeight Floor Height (without flooring) to Ceiling height (without suspended ceiling)

for this space (measured from top of slab of this space to the bottom of slabof space above); the average shall be taken if room shape is not prismatic.

IfcQuantityLength

ClearHeight Clear Height between floor level (including finish) and ceiling level(including finish and sub construction) of this space; the average shall betaken if room shape is not prismatic.

IfcQuantityLength

GrossPerimeter Calculated gross perimeter at the floor level of this space. It all sides of thespace, including those parts of the perimeter that are created by virtualboundaries and openings. The exact definition and calculation rules dependon the method of measurement used.

IfcQuantityLength

NetPerimeter Calculated net perimeter at the floor level of this space. It normallyexcludes those parts of the perimeter that are created by by virtualboundaries and openings. The exact definition and calculation rules dependon the method of measurement used.

IfcQuantityLength

GrossFloorArea Calculated sum of all floor areas covered by the space. It normally includesthe area covered by elementsinside the space (columns, inner walls, etc.).The exact definition and calculation rules depend on the method ofmeasurement used.

IfcQuantityArea

NetFloorArea Calculated sum of all usable floor areas covered by the space. It normallyexcludes the area covered by elements inside the space (columns, innerwalls, etc.), floor openings, or other protruding elements. Special rulesapply for areas that have a low headroom. The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityArea

GrossCeilingArea Calculated sum of all ceiling areas of the space. It normally includes thearea covered by elementsinside the space (columns, inner walls, etc.). Theceiling area is the real (and not the projected) area (e.g. in case of slopedceilings). The exact definition and calculation rules depend on the methodof measurement used.

IfcQuantityArea

NetCeilingArea Calculated sum of all ceiling areas covered by the space. It normallyexcludes the area covered by elements inside the space (columns, innerwalls, etc.) or by ceiling openings. The ceiling area is the real (and not theprojected) area (e.g. in case of sloped ceilings). The exact definition andcalculation rules depend on the method of measurement used.

IfcQuantityArea

GrossWallArea Calculated sum of all wall areas bounded by the space. It normally includesthe area covered by elementsinside the wall area (doors, windows, otheropenings, etc.). The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityArea

NetWallArea Calculated sum of all wall areas bounded by the space. It normally excludesthe area coveredby elements inside the wall area (doors, windows, otheropenings, etc.). Special rules apply for areas that have a low headroom.The exact definition and calculation rules depend on the method ofmeasurement used.

IfcQuantityArea

GrossVolume Calculated gross volume of all areas enclosed by the space (normallyincluding the volume of construction elements inside the space). The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityVolume

NetVolume Calculated net volume of all areas enclosed by the space (normallyexcluding the volume of construction elements inside the space). The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityVolume

Page 94: de werkwijze en open standaarden

IfcSpacePset_SpaceCommon

Name Definition Data Type

Reference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierCategory Category of space usage or utilization of the area. It is defined according to

the presiding national building code.IfcLabel

FloorCovering Label to indicate the material or finish of the space flooring. The label isused for room book information and often displayed in room stamp.

IfcLabel

WallCovering Label to indicate the material or finish of the space flooring. The label isused for room book information and often displayed in room stamp.

IfcLabel

CeilingCovering Label to indicate the material or finish of the space flooring. The label isused for room book information and often displayed in room stamp.

IfcLabel

SkirtingBoard Label to indicate the material or construction of the skirting board aroundthe space flooring. The label is used for room book information and oftendisplayed in room stamp.

IfcLabel

GrossPlannedArea Total planned area for the space. Used for programming the space. IfcAreaMeasure /AREAUNIT

NetPlannedArea IfcAreaMeasure /AREAUNIT

PubliclyAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas a publicly accessible space, e.g., for a public toilet (TRUE) or not(FALSE).

IfcBoolean

HandicapAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas an accessible space for handicapped people, e.g., for a public toilet(TRUE) or not (FALSE). This information is often used to declare the needfor access for the disabled and for special design requirements of thisspace.

IfcBoolean

ConcealedFlooring Indication whether this space is declared to be a concealed flooring (TRUE)or not (FALSE). A concealed flooring is normally meant to be the spacebeneath a raised floor.

IfcBoolean

ConcealedCeiling Indication whether this space is declared to be a concealed ceiling (TRUE)or not (FALSE). A concealed ceiling is normally meant to be the spacebetween a slab and a suspended ceiling.

IfcBoolean

Pset_SpaceCommon

Page 95: de werkwijze en open standaarden

IfcSpacePset_SpaceFireSafetyRequirements, Pset_SpaceLightingRequirements,Pset_SpaceOccupancyRequirements

MainFireUse Main fire use for the space which is assigned from the fire use classificationtable as given by the relevant national building code.

IfcLabel

AncillaryFireUse Ancillary fire use for the space which is assigned from the fire useclassification table as given by the relevant national building code.

IfcLabel

FireRiskFactor Fire Risk factor assigned to the space according to local buildingregulations.

IfcLabel

FireHazardFactor Fire hazard code of the space. The coding depends on the national firesafety regulations.

IfcLabel

FlammableStorage Indication whether the space is intended to serve as a storage of flammablematerial (which is regarded as such by the presiding building code. (TRUE)indicates yes, (FALSE) otherwise.

IfcBoolean

FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here whether the space (in case of e.g., acorridor) is designed to serve as an exit space, e.g., for fire escapepurposes.

IfcBoolean

SprinklerProtection Indication whether the space is sprinkler protected (TRUE) or not (FALSE). IfcBooleanSprinklerProtectionAutomatic Indication whether the space has an automatic sprinkler protection (TRUE)

or not (FALSE). It should only be given, if the property "SprinklerProtection"is set to TRUE.

IfcBoolean

AirPressurization Indication whether the space is required to have pressurized air (TRUE) ornot (FALSE).

IfcBoolean

ArtificialLighting Indication whether this space requires artificial lighting (as natural lightingwould be not sufficient). (TRUE) indicates yes (FALSE) otherwise.

IfcBoolean

Illuminance Required average illuminance value for this space. IfcIlluminanceMeasure / ILLUMINANCEUNIT

OccupancyType Occupancy type for this object. It is defined according to the presidingnational building code.

IfcLabel

OccupancyNumber Number of people required for the activity assigned to this space. IfcCountMeasureOccupancyNumberPeak Maximal number of people required for the activity assigned to this space in

peak time.IfcCountMeasure

OccupancyTimePerDay The amount of time during the day that the activity is required within thisspace.

IfcTimeMeasure /TIMEUNIT

AreaPerOccupant Design occupancy loading for this type of usage assigned to this space. IfcAreaMeasure /AREAUNIT

MinimumHeadroom Headroom required for the activity assigned to this space. IfcLengthMeasure /LENGTHUNIT

IsOutlookDesirable An indication of whether the outlook is desirable (set TRUE) or not (setFALSE)

IfcBoolean

Pset_SpaceFireSafetyRequirements

Pset_SpaceLightingRequirements

Pset_SpaceOccupancyRequirements

Page 96: de werkwijze en open standaarden

IfcSpacePset_SpaceThermalRequirements

SpaceTemperatureMax Temperature of the space or zone, that is required from user/designer viewpoint. If no summer or winter space temperature requirements are given, itapplies all year, otherwise for the intermediate period.

IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

SpaceTemperatureMin Minimal temperature of the space or zone, that is required fromuser/designer view point. If no summer or winter space temperaturerequirements are given, it applies all year, otherwise for the intermediateperiod.

IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

SpaceTemperatureSummerMax Maximal temperature of the space or zone for the hot (summer) period, thatis required from user/designer view point.

IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

SpaceTemperatureSummerMin Minimal temperature of the space or zone for the hot (summer) period, thatis required from user/designer view point.

IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

SpaceTemperatureWinterMax Maximal temperature of the space or zone for the cold (winter) period, thatis required from user/designer view point.

IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

SpaceTemperatureWinterMin Minimal temperature of the space or zone for the cold (winter) period, thatis required from user/designer view point.

IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

SpaceHumidity Humidity of the space or zone that is required from user/designer viewpoint. If no summer or winter space humidity requirements are given, itapplies all year, otherwise for the intermediate period.

IfcRatioMeasure

SpaceHumiditySummer Humidity of the space or zone for the hot (summer) period, that is requiredfrom user/designer view point.

IfcRatioMeasure

SpaceHumidityWinter Humidity of the space or zone for the cold (winter) period that is requiredfrom user/designer view point.

IfcRatioMeasure

DiscontinuedHeating Indication whether discontinued heating is required/desirable fromuser/designer view point. (TRUE) if yes, (FALSE) otherwise.

IfcBoolean

NaturalVentilation Indication whether the space is required to have natural ventilation (TRUE)or mechanical ventilation (FALSE).

IfcBoolean

NaturalVentilationRate Indication of the requirement of a particular natural air ventilation rate,given in air changes per hour.

IfcCountMeasure

MechanicalVentilationRate Indication of the requirement of a particular mechanical air ventilation rate,given in air changes per hour.

IfcCountMeasure

AirConditioning Indication whether this space requires air conditioning provided (TRUE) ornot (FALSE).

IfcBoolean

AirConditioningCentral Indication whether the space requires a central air conditioning provided(TRUE) or not (FALSE). It should only be given, if the property"AirConditioning" is set to TRUE.

IfcBoolean

Pset_SpaceThermalRequirements

Page 97: de werkwijze en open standaarden

IfcSpacePset_SpaceThermalDesign

CoolingDesignAirflow The air flowrate required during the peak cooling conditions. IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT

HeatingDesignAirflow The air flowrate required during the peak heating conditions, but could alsobe determined by minimum ventilation requirement or minimum air changerequirements.

IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT

TotalSensibleHeatGain The total sensible heat or energy gained by the space during the peakcooling conditions.

IfcPowerMeasure /POWERUNIT

TotalHeatGain The total amount of heat or energy gained by the space at the time of thespace's peak cooling conditions.

IfcPowerMeasure /POWERUNIT

TotalHeatLoss The total amount of heat or energy lost by the space at the time of thespace's peak heating conditions.

IfcPowerMeasure /POWERUNIT

CoolingDryBulb Inside dry bulb temperature for cooling design IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

CoolingRelativeHumidity Inside relative humidity for cooling design. IfcPositiveRatioMeasure

HeatingDryBulb Inside dry bulb temperature for heating design IfcThermodynamicTemperatureMeasure /THERMODYNAMICTEMPERATUREUNIT

HeatingRelativeHumidity Inside relative humidity for heating design. IfcPositiveRatioMeasure

VentilationAirFlowrate Ventilation outside air requirement for the space. IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT

ExhaustAirFlowrate Design exhaust air flow rate for the space. IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT

CeilingRAPlenum Ceiling plenum used for return air or not. TRUE = Yes, FALSE = No. IfcBooleanBoundaryAreaHeatLoss Heat loss per unit area for the boundary object. This is a design input value

for use in the absence of calculated load data.IfcHeatFluxDensityMeasure /HEATFLUXDENSITYUNIT

Pset_SpaceThermalDesign

Page 98: de werkwijze en open standaarden

Base Quantities

IfcStairQuantities

Name Description Value TypeBottom Area Total area of the cross section (or profile) of the stair. The exact definition

and calculation rules depend on the method of measurement used.Solibri analysis

Volume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value Type

Page 99: de werkwijze en open standaarden

IfcStairPset_StairCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierNumberOfRiser Total number of the risers included in the stair IfcCountMeasureNumberOfTreads Total number of treads included in the stair IfcCountMeasureRiserHeight Vertical distance from tread to tread. The riser height is supposed to be

equal for all steps of a stair or stair flight.IfcPositiveLengthMeasure / LENGTHUNIT

TreadLength Horizontal distance from the front of the thread to the front of the nexttread. The tread length is supposed to be equal for all steps of the stair orstair flight at the walking line.

IfcPositiveLengthMeasure / LENGTHUNIT

RequiredHeadroom Required headroom clearance for the passageway according to theapplicable building code or additional requirements

IfcPositiveLengthMeasure / LENGTHUNIT

HandicapAccessible Indication that this object is designed to be accessible by the handicapped.Set to (TRUE) if this stair is rated as handicap accessible according thelocal building codes, otherwise (FALSE). Accessibility maybe provided byadditional means.

IfcBoolean

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

FireRating Fire rating for this object. It is given according to the national fire safetyclassification.

IfcLabel

FireExit Indication whether this object is designed to serve as an exit in the case offire (TRUE) or not (FALSE). Here it defines an exit stair in accordance to thenational building code.

IfcBoolean

HasNonSkidSurface Indication whether the surface finish is designed to prevent slippery (TRUE)or not (FALSE).

IfcBoolean

Page 100: de werkwijze en open standaarden

Base Quantities

IfcSuspendedCeilingQuantities

Name Description Value TypeArea Total area of the covering in the elevation view taking into account

possible openings. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Thickness The thickness measure is the value of a distance Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value TypeGrossArea Total area of the covering in the elevation view. The exact definition and

calculation rules depend on the method of measurement used.IfcQuantityArea

NetArea Total area of the covering in the elevation view taking into accountpossible openings. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityArea

Page 101: de werkwijze en open standaarden

IfcSuspendedCeilingPset_CoveringCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety

classification.IfcLabel

AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

FlammabilityRating Flammability Rating for this object. It is given according to the nationalbuilding code that governs the rating of flammability for materials.

IfcLabel

FragilityRating Indication on the fragility of the covering (e.g., under fire conditions). It isgiven according to the national building code that might provide aclassification for fragility.

IfcLabel

SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.

IfcLabel

Material Main material of the covering, it should only be given, if no IfcMaterialclass is assigned to the IfcCovering instance.

IfcLabel

Combustible Indication whether the object is made from combustible material (TRUE) ornot (FALSE).

IfcBoolean

TotalThickness Thickness of the covering, The thickness information is provided in additionto the shape representation and the geometric parameters used within. Incases of inconsistency between the geometric parameters and the shapeproperties, provided in the attached property, the geometric parameterstake precedence.

IfcPositiveLengthMeasure / LENGTHUNIT

Finish Finish selection for this object. Here specification of the surface finish forinformational purposes

IfcText

Page 102: de werkwijze en open standaarden

IfcWallQuantities

Name Description Value TypeArea Area of the wall as viewed by an elevation view of the middle plane. It does

take into account all wall modifications (such as openings). The exactdefinition and calculation rules depend on the method of measurementused.

Solibri analysis

Area (minimum) Other side of the same wall (see Area, often the same value) Solibri analysisGross Area Area of the wall as viewed by an elevation view of the middle plane of the

wall. It does not take into account any wall modifications (such asopenings). The exact definition and calculation rules depend on the methodof measurement used.

Solibri analysis

Gross Area (minimum) Other side of the same wall (see Gross Area, often the same value) Solibri analysisArea of Doors Area of the doors in the wall as viewed by an elevation view of the middle

plane. The exact definition and calculation rules depend on the method ofmeasurement used.

Solibri analysis

Area of Windows Area of the windows in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Area of Openings Area of the openings in the wall as viewed by an elevation view of themiddle plane. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Bottom Area Total area of the cross section (or profile) of the wall. The exact definitionand calculation rules depend on the method of measurement used.

Solibri analysis

Height The height measure is the value of a distance Solibri analysisHeight (minimum) Other side of the same wall (see Height, often the same value) Solibri analysisLength A length measure is the value of a distance Solibri analysisLength (minimum) Other side of the same wall (see Length, often the same value) Solibri analysisThickness The thickness measure is the value of a distance Solibri analysisThickness (minimum) Other side of the same wall (see Thickness, often the same value) Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Page 103: de werkwijze en open standaarden

IfcWall

Base QuantitiesName Description Value TypeNominalLength Total nominal (or average) length of the wall along the wall path. The exact

definition and calculation rules depend on the method of measurementused.

IfcQuantityLength

NominalWidth Total nominal (or average) width (or thickness) of the wall perpendicular tothe wall path. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityLength

NominalHeight Total nominal (or average) height of the wall along the wall path. The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityLength

GrossFootprintArea Area of the wall as viewed by a ground floor view, not taking any wallmodifications (like recesses) into account. It is also referred to as the footprint of the wall. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityArea

NetFootprintArea Area of the wall as viewed by a ground floor view, taking all wallmodifications (like recesses) into account. It is also referred to as the footprint of the wall. The exact definition and calculation rules depend on themethod of measurement used.

IfcQuantityArea

GrossSideArea Area of the wall as viewed by an elevation view of the middle plane of thewall. It does not take into account any wall modifications (such asopenings). The exact definition and calculation rules depend on the methodof measurement used.

IfcQuantityArea

NetSideArea Area of the wall as viewed by an elevation view of the middle plane. It doestake into account all wall modifications (such as openings). The exactdefinition and calculation rules depend on the method of measurementused.

IfcQuantityArea

GrossSideAreaLeft Area of the wall as viewed by an elevation view of the left side (whenviewed along the wall path orientation). It does not take into account anywall modifications (such as openings). The exact definition and calculationrules depend on the method of measurement used.

IfcQuantityArea

NetSideAreaLeft Area of the wall as viewed by an elevation view of the left side (whenviewed along the wall path orientation). It does take into account all wallmodifications (such as openings). The exact definition and calculation rulesdepend on the method of measurement used.

IfcQuantityArea

GrossSideAreaRight Area of the wall as viewed by an elevation view of the right side (whenviewed along the wall path orientation). It does not take into account anywall modifications (such as openings). The exact definition and calculationrules depend on the method of measurement used.

IfcQuantityArea

NetSideAreaRight Area of the wall as viewed by an elevation view of the right side (whenviewed along the wall path orientation). It does take into account all wallmodifications (such as openings). The exact definition and calculation rulesdepend on the method of measurement used.

IfcQuantityArea

GrossVolume Volume of the wall, without taking into account the openings and theconnection geometry. The exact definition and calculation rules depend onthe method of measurement used.

IfcQuantityVolume

NetVolume Volume of the wall, after subtracting the openings and after considering theconnection geometry. The exact definition and calculation rules depend onthe method of measurement used.

IfcQuantityVolume

Page 104: de werkwijze en open standaarden

IfcWall

Pset_WallCommonName Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierAcousticRating Acoustic rating for this object. It is giving according to the national building

code. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

FireRating Fire rating given according to the national fire safety classification. IfcLabelCombustible Indication whether the object is made from combustible material (TRUE) or

not (FALSE).IfcBoolean

SurfaceSpreadOfFlame Indication on how the flames spread around the surface, It is givenaccording to the national building code that governs the fire behaviour formaterials.

IfcLabel

ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. Here the totalthermal transmittance coefficient through the wall (including all materials).

IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

ExtendToStructure Indicates whether the object extend to the structure above (TRUE) or not(FALSE).

IfcBoolean

LoadBearing Indicates whether the object is intended to carry loads (TRUE) or not(FALSE).

IfcBoolean

Compartmentation Indication whether the object is designed to serve as a firecompartmentation (TRUE) or not (FALSE).

IfcBoolean

Page 105: de werkwijze en open standaarden

Base Quantities

IfcWindowQuantities

Name Description Value TypeArea Total area of the window in the elevation view. The exact definition and

calculation rules depend on the method of measurement used.Solibri analysis

Height The height measure is the value of a distance Solibri analysisWidth The width measure is the value of a distance Solibri analysisFrame Length A length measure is the value of a distance Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

Name Description Value Type

Page 106: de werkwijze en open standaarden

IfcWindowPset_WindowCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierFireRating Fire rating for this object. It is given according to the national fire safety

classification.IfcLabel

AcousticRating Acoustic rating for this object. It is giving according to the national buildingcode. It indicates the sound transmission resistance of this object by anindex ration (instead of providing full sound absorbtion values).

IfcLabel

SecurityRating Index based rating system indicating security level. It is giving according tothe national building code.

IfcLabel

IsExternal Indication whether the element is designed for use in the exterior (TRUE)or not (FALSE). If (TRUE) it is an external element and faces the outside ofthe building.

IfcBoolean

Infiltration Infiltration flowrate of outside air for the filler object based on the area ofthe filler object at a pressure level of 50 Pascals. It shall be used, if thelength of all joints is unknown.

IfcVolumetricFlowRateMeasure /VOLUMETRICFLOWRATEUNIT

ThermalTransmittance Thermal transmittance coefficient (U-Value) of a material. It applies to thetotal door construction.

IfcThermalTransmittanceMeasure /THERMALTRANSMITTANCEUNIT

GlazingAreaFraction Fraction of the glazing area relative to the total area of the filling element.It shall be used, if the glazing area is not given separately for all panelswithin the filling element.

IfcPositiveRatioMeasure

SmokeStop Indication whether the object is designed to provide a smoke stop (TRUE)or not (FALSE).

IfcBoolean

Page 107: de werkwijze en open standaarden

Base Quantities

Quantities

IfcZone

Name Description Value Type

Name Description Value TypeArea Total area of the extruded area of the zone, taking into account possible

zone openings. The exact definition and calculation rules depend on themethod of measurement used.

Solibri analysis

Height The height measure is the value of a distance Solibri analysisPerimeter The perimeter measure of the space is the value of a distance Solibri analysisArea of Doors Total area of doors Solibri analysisArea of Windows Total area of windows Solibri analysisVolume A volume measure is the value of the solid content of a body Solibri analysisBounding Box Height The IfcBoundingBox is defined with an own location which can be used to

place the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Height attribute (measured along the edge parallel to theZ Axis)

Solibri analysis

Bounding Box Length The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Length attribute (measured along the edge parallel to theX Axis)

Solibri analysis

Bounding Box Width The IfcBoundingBox is defined with an own location which can be used toplace the IfcBoundingBox relative to the geometric coordinate system.The IfcBoundingBox is defined by the lower left corner (Corner) and theupper right corner (XDim, YDim, ZDim measured within the parent co-ordinate system). Width attribute (measured along the edge parallel to theY Axis)

Solibri analysis

IfcZone

IfcSpace 1 IfcSpace 2

Page 108: de werkwijze en open standaarden

*Also Pset_Space.... parameters can be used

IfcZonePset_ZoneCommon

Name Definition Data TypeReference Reference ID for this specified type in this project (e.g. type 'A-1') IfcIdentifierCategory Category of space usage or utilization of the area. It is defined according to

the presiding national building code.IfcLabel

GrossAreaPlanned Total planned gross area for the space. Used for programming the space. IfcAreaMeasure /AREAUNIT

NetAreaPlanned Total planned net area for the space. Used for programming the space. IfcAreaMeasure /AREAUNIT

PubliclyAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas a publicly accessible space, e.g., for a public toilet (TRUE) or not(FALSE).

IfcBoolean

HandicapAccessible Indication whether this space (in case of e.g., a toilet) is designed to serveas an accessible space for handicapped people, e.g., for a public toilet(TRUE) or not (FALSE). This information is often used to declare the needfor access for the disabled and for special design requirements of thisspace.

IfcBoolean

IfcZone

IfcSpace 1 IfcSpace 2

Page 109: de werkwijze en open standaarden

IJpelaar - Breda

4

Page 110: de werkwijze en open standaarden

Pontsteiger - Amsterdam

4

Page 111: de werkwijze en open standaarden

BIMvan structuur naar

de gewenste output

versie20150623

INFORMATIEIDENTIFICATION

PLATTEGROND

GEVELAANZICHTDOORSNEDE

SCHEDULE

DETAIL 1:5

3D + tags 3D + tags + 2D opmaak

LOCATION QUANTITYPSET_**COMMON

SPECIFIEK PER ENTITEIT

MANUFACTURER WARRANTY

IFC PARAMETERS - COMMON PROPERTYSET

NL-SFBBOUWLAAG

NAAM GEBOUW

RUIMTE NAAM ZONENAME2 - BOUWNUMMERZONENAME - WONINGTYPE

GROEPERING VAN RUIMTEN

SITE

PROJECTNAAM

30

§2.1.2Lokale positie en orientatie

RVB BIM NORM V1.1

§2.2.7.2Terrein

§2.2.4Bestandsformaat- en naam

§2.2.7.1Project

§2.1.2Lokale positie en orientatie

§2.2.6.4ObjectGUID

§2.1.4Entiteiten

§2.2.7.7Groepering van ruimten

§2.2.7.3Bouwwerk

§2.2.6.2Informatie- indeling

§2.2.7.8Elementen

§2.1.9Bouwlaagindeling

§2.2.6.3Objectrelaties

§2.1.5Nauwkeurigheid

§2.2.7.6Ruimte

§2.1.2Lokale positie en orientatie

<bouwlaagnummer><verdiepingsoort>

<spatie><tekstuele beschrijving>

IFC 2X3 NL-SfB codering NEN 2574

Page 112: de werkwijze en open standaarden

www.duravermeer.nl

DURA VERMEER DIVISIE BOUW EN VASTGOED BV

De Bouw 793991 SX HoutenT (030) 288 16 [email protected]