DAB+ headend aXemble manual V2 - Broadcast Partners · DAB+ chain overview with aXemble hardware...
Transcript of DAB+ headend aXemble manual V2 - Broadcast Partners · DAB+ chain overview with aXemble hardware...
DAB+ headend aXemble
manual V2.0
Broadcast Partners
June 2018
Broadcast Partners1 Axelsestraat 58 NL - 4537 AL Terneuzen T. +31 115 683555 www.broadcastpartners.nl
Auteurs: Davy van Delft / Rene van de Kolk
Nummer: Tnz 185070
Alle rechten voorbehouden. Niets uit dit rapport mag vermenigvuldigd en/of openbaar gemaakt worden door middel van druk,
fotokopie, microfilm of op welke andere wijze dan ook, zonder voorafgaande schriftelijke toestemming van Broadcast Part-
ners.
© 2018 Broadcast Partners
1 Broadcast Partners is de handelsnaam van Broadcast Digital Networks B.V. De onderneming is ingeschreven in het handels-
register van de Kamer van Koophandel onder nummer 54982979.
Content
Introduction
Inlog aXemble
1. Audio sources ........................................................................................... 4
2. Services ................................................................................................... 7
3. Multiplexes ............................................................................................. 13
4. Dashboard.............................................................................................. 18
5. Connecting ............................................................................................. 20
Introduction
DAB+ chain overview with aXemble hardware
The aXemble DAB+ headend is a multiplexer that gathers different DAB+ program
streams and their audio sources and produces the necessary signalling and EDI output
required for DAB+ transmission.
The aXemble headend uses a user-friendly web interface to configure audio sources,
program services and the multiplex.
Besides the headend, a standalone aXemble Audio encoder is separate available.
In this document we describe the aXemble DAB+ headend V2.0 released June 2018.
Inlog
To configure the aXemble DAB+ headend from factory preset, connect your device to
the aXemble, open an internet browser and open the following url:
http://10.0.10.15
Username : admin
Password : password
In Settings page, on top an option for future build firmware releases is available.
Backup allows you to make a local backup or restore a upload to the aXemble.
In the license code field, an overview of available services is in overview. Modifications
can be done to activate more services.
Timezone options can be modified as of customers wishes. An overview of live NTP set-
tings is available in the dashboard below the settings.
In the administration field you can modify inlog on aXemble with a personal password.
The control interface and datainterface can be modified manual on preffered IP ranges.
In the network configuration an overview of live network performance is available.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
1. Audio Sources
Main page aXemble audio sources:
The audio sources overview can be shown by selecting audio sources from the main
menu on the left.
Press to add a new audio source or press to edit an existing audio source.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
General settings:
NAME: Provide a name for the audio
source for easy selection when adding an audio source to a service. (required) COMMENT: Provide a more detailed de-
scription of the audio source if needed. (optional)
TYPE: Select the type of audio source
used:
- Stream (Icecast of SHOUTcast
stream)
- Stream - PCM (PCM stream from de-
vice)
- AES/EBU (Digital input XLR)
- Analog (Analog input left and right
XLR) This option only in aXemble en-
coder
- Livewire host connection
- aXemble encoder connection
- SDP file configuration for Ravenna /
Dante available
GAIN: gain that can be applied by the
encoder
Audio source types:
1 – Stream
Provide a streaming url (i.e. icecast, shoutcast or other streaming servers)
2 – Stream – PCM
Provide a streaming url from an AoIP encoder which provides a PCM stream.
Select the needed fourcc codec (most common is s16l) and the PCM stream sample rate
(only 48 and 32 kHz supported)
Broadcast Partners
Tnz 185070 DAB+manual aXemble
3 – AES/EBU
Select AES/EBU to use the digital XLR input (currently 1 input available)
4 – Analog
Select Analog to use the 2 analog XLR inputs (currently 1 input available)
5 – Livewire
Select Livewire host to use this AoIP protocol
6- aXemble encoder
Select this option to connect the aXemble separate encoder
unit
7- Ravenna / Dante protocol
Select this option to use this function and define your SDP-
file content parameters
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Note:
Currently only 1 digital or 1 analog input can be used. This option is only for aXemble
encoder.
Although both source types can be selected and used in multiple services, only the last
service and last selected source type will be active.
Save / Delete settings
Remember to save all settings by pressing Save in the right bottom corner.
Optionally you can delete an audio source by pressing Delete
Broadcast Partners
Tnz 185070 DAB+manual aXemble
2. Services
Main page aXemble services:
The services overview can be shown by selecting Services from the main menu on the left.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Main page edit services:
NAME: Provide a name for the service for
easy selection when adding a service to a multiplex.
(required)
COMMENT: Provide a more detailed descrip-
tion of the service if needed. (optional)
LABEL: Provide a label which describes the
service. The label will be displayed in the services selection list on the display of the DAB+ receiver. Max. 16 characters allowed (required)
SHORT LABEL: Provide a short label of max. 8
characters containing no other than the characters used in LABEL. (case sensitive)
to add a new service or press to edit an existing service. Use to duplicate.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
REGION: Select the region where the DAB
transmitters will operate.
PROGRAM TYPE: Select the desired program
type to identify the programme content for their intended audience.
COUNTRY: Select the country where the
DAB transmitters will operate.
SERVICE ID: Provide a unique ID that identi-
fies the service within a multiplex
LANGUAGE ID: Select the desired language
to identify the programme for the re-ceiver. PROTECTION: Select a desired Equal Error
Protection (*1). EEP-3A is the most com-mon used protection.
BITRATE: Select a desired bitrate. >= 96
kbps is recommended for music. aXemble sets the sample rate, audio mode and SBR to recommended settings.
SAMPLE RATE: Select a desired sample rate.
The DAB+ encoder resamples the input. When using AES input, the chosen sample rate must match the sample rate of the AES input signal.
AUDIO MODE: Select a desired audio mode.
Parametric Stereo is disabled and cannot be used in combination with bitrates above 64 kbps.
See table 1. for recommended settings.
SBR: Spectral Band Replication is an option
to enhance audio or speech codecs, es-pecially at low bit rates. SBR cannot be
used for bitrates above 128 kbps.
CAPACITY: Capacity shows the CU’s
(Capacity Units) that the service occu-
pies in the whole service. 864 CU’s
max.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Audio Source: Select an audio source needed for the
service. (required) Backup audio source provides the possibility to add a secondary feed. In case of interruption automatisch switchover is availa-ble. Time settings for switchover adjustable from 10 till 60 seconds before watchdog activates backup source switched on air. Manual reset to main feed is the preffered way to manage. (re-ferring to latency times in STL)
PAD: Select the preferred PAD size for the associ-
ated data file
DLS: Provide a text string to run alongside the
DAB+ programme. Dynamic Label Segment is similar to RDS on FM Radio. Slideshow: Select one or more images to be dis-
played on SLS capable DAB+ receivers. Multiple
images will be displayed as a slideshow, chang-
ing at a 10 sec. interval. Images larger than
320x240px or with a file size exceeding 50kb will
be automatically resized
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Table 1: Recommended Audio mode settings
Bitrate
Sam-
ple
rate
Audio
mode
PS
recommen-
ded
PS
availa-
ble
SBR recom-
mended
SBR
availa-
ble
24 32 ste-
reo
√ √ √ √
32 32 ste-
reo
√ √ √ √
40 32 ste-
reo
√ √ √ √
48 32 ste-
reo
√ √ √ √
56 48 ste-
reo
√ √ √ √
64 48 ste-
reo
√ √ √ √
72 32 ste-
reo
√ √
80 32 ste-
reo
√ √
88 32 ste-
reo
√ √
96 48 ste-
reo
√
104 48 ste-
reo
√
112 48 ste-
reo
√
120 48 ste-
reo
√
128 48 ste-
reo
√
136 48 ste-
reo
144 48 ste-
reo
152 48 ste-
reo
160 48 ste-
reo
168 48 ste-
reo
Broadcast Partners
Tnz 185070 DAB+manual aXemble
176 48 ste-
reo
184 48 ste-
reo
192 48 ste-
reo
Save / Delete settings
Remember to save all settings by pressing Save in the right bottom corner.
Optionally you can delete a service by pressing Delete
Broadcast Partners
Tnz 185070 DAB+manual aXemble
3. Multiplexes
Main page aXemble multiplexes:
The multiplexes overview can be shown by selecting Multiplexes from the main menu on
the left.
If a multiplex is configured, press to activate the multiplex and start the EDI
transport stream or press to stop a multiplex.
Press to add a new multiplex or press to edit an existing multiplex.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Main page aXemble edit multiplexes:
Broadcast Partners
Tnz 185070 DAB+manual aXemble
NAME: Provide a name for the multi-
plex.
COMMENT: Provide a more detailed
description of the multiplex if needed. (optional)
DABMODE: Currently only DAB transmis-
sion mode I is supported. Choose to operate the transmitter in MFN mode (Multi Frequency Network) or SFN mode (Single Frequency Network). MFN is chosen for a single transmitter and SFN is needed if more than 1 transmitter will operate in a network. COUNTRY: Select the country where the
DAB transmitters will operate.
ENSEMBLE ID: Provide a 4 digit ID to
identify the multiplex. For test pur-poses this ID can be anything but when used on-air this ID must be unique among other multiplexes.
LOCAL TIME OFFSET: Choose a system
time offset if needed. Auto is the pre-ferred selection. LANGUAGE ID: Choose
the language used for services in the
multiplex
LABEL: Provide a label which describes
the multiplex. The label will be dis-played in advanced information
menu’s of the DAB+ receiver. Max. 16
characters allowed (required)
SHORT LABEL: Provide a short label of
max. 8 characters containing none other than the characters used in LABEL. (case sensitive)
Services:
To add services to the multiplex, select a configured service and click
The horizontal bar will show how many capacity units are used and how many are avail-
able
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Multiplex destinations
The generated multiplex (EDI transport stream) can be sent to multiple transmitters.
Both unicast and multicast streams can be used.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
DESTINATION PORT: Provide a destination port on which the transmitter will listen. The
destination port is used for all destinations
REED SOLOMON EDI-FEC: FEC is a Forward Error Correction mechanism to detect and correct
multiple symbol errors in the transport stream. FEC 0 can be used on LAN networks,
for other networks FEC 5 is recommended.
Destinations
Select type (unicast/multicast) and add a description and a destination IP-address and
press to add the destination to the multiplex.
Press to remove a destination entry.
Save / Delete settings
Remember to save all settings by pressing Save in the right bottom corner.
Optionally you can delete a multiplex by pressing Delete
Broadcast Partners
Tnz 185070 DAB+manual aXemble
4. Dashboard
Finally at the main dashboard overview, general performance of the aXemble multiplexer
with the channels on air in the multiplex is available. At this main page also the logout
is available for the user interface. At dashboard in one overview of all services including
audio indication, live DLS and SLS monitoring. Also live refresh of all SLS pictures is
shown at this page. On the top of the dashboard live viewing of logs regarding aXemble
performance is available.
All the necessary IP network settings can be changed in the network
preferences. For security password reset can be done in the administration tool.
In the maintenance section, the availability of updating firmware is one option.
aXemble functionality will be updated and it is possible to update aXemble
remote webbased, in cooperation.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
5. Connecting
The aXemble headend is configured with the following IP-addresses:
Control interface (CTRL) : IP 192.168.12.34
Data interface (DATAT) : IP 10.0.0.10
When assigning a static IP address on the laptop or PC in the range of one of
the above IP-addresses, i.e. 10.0.0.15, the web interface can be opened
To logon, the username and password are admin and password
Then from the settings menu in the top right corner, the network settings can
be changed.
Reboot after changes to the ip-adress(es) have been made.
Broadcast Partners
Tnz 185070 DAB+manual aXemble
The aXemble headend is configured with a Multiplex which can be found when
selecting Multiplex from the left-side menu
Broadcast Partners
Tnz 185070 DAB+manual aXemble
Choose Edit to change the output destination of the Multiplex EDI stream
(transmitter EDI input IP and port)
Step 1 : add a unicast or multicast destination
Step 2 : add destination to the list.
Step 3 : change Port number to the listening port of the EDI device
Step 4 : Save
Step 5: In the Multiplex overview: choose Deactivate to stop the active mul-
tiplex, and after that press Activate to start the multiplex with the new set-
tings.
Broadcast Partners
Tnz 185070 DAB+manual aXemble